Installation manual Owner manual

Installation Instructions
TH-PT8
Projector | Suspended Ceiling Tile 8"
Component Checklist
IMPORTANT INFORMATION:
! IMPORTANT - Install Telehook Projector - Suspended Ceiling Tile 8" as per Installation Instructions.
! This product supports 1.5” NPT Pole Mounts, Atdec Pole Mount (TH-WH-PJ-CM), and Atdec Flush Mount (TH-WH-PJ-FM).
! Maximum weight capacity 22.7kg (50lbs).
! The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Remove Existing Ceiling Tile
Remove existing ceiling tile from ceiling grid where the product
is going to be installed.
NOTE: Keep this ceiling tile for later in the installation.
TIP: Also temporarily remove an adjacent ceiling tile to allow easy
access to the product during installation.
Step 3. Fix Anchors to True Ceiling
Uncoil Support Wire and cut into 4 equal lengths. Select the anchoring method appropriate to your ceiling (see below).
NOTE: Each anchor point should be directly above each corner of the Suspended Ceiling Tile.
Wooden Joists
Drill 4x Ø6mm holes, at least 50mm deep
(4x ؼ
” holes, 2”deep).
Fully screw Lag Eye bolts into wooden joists.
Solid Concrete
Drill 4x Ø6mm holes, 36mm deep
(4x ؼ
” holes 1½ ” deep).
Tap anchors into hole to an embedded depth
of at least 25mm deep (1” deep).
Using a claw hammer, pull anchor out 6mm
(¼
” ) to activate anchor.
Truss Beams
Thread one end of Support Wires through the
trusses, and wrap 5 times to secure.
Hardware
M6 Wing
Nut (x4)
M6 Washer
(x8)
Lag Eye
Bolt (x4)
Concrete
Anchor
Bolt (x4)
Safety Clamp
(x2)
Thread one end of each support wires through
a Lag Eye Bolt, and wrap 5 times to secure.
Thread one end of each support wires through
a Lag Eye Bolt, and wrap 5 times to secure.
Support Wire (x4)
Lag Eye Bolt (x4)
Concrete Anchor
Bolt (x4)
Support Wire (x4)
Truss Beam
Support
Wire (x4)
Solid
Concrete
Wooden
Joist
M6 Set
Screw (x2)
Turnbuckle
(x4)
Support Wire
Safety Wire
M6x16mm
Screw (x4)
M5x16mm
Screw (x4)
Upper
Mounting Plate
Lower
Mounting Plate
Mounting
Collar
3mm
Allen Key
Turnbuckle
Hooks
Tools Required:
Phillips head screwdriver
Wire cutters
Power drill
6mm (
1
/
4
”) drill bit
6mm (
1
/
4
”) masonry drill bit
Claw hammer
Jigsaw/Hole cutter
Spirit level
Suspended
Ceiling Tile
Ceiling Covers
(x3)
OR
OR
Step 4. Attach Turnbuckles onto Support Wires
Loop each dangling Support Wire through a Turnbuckle, and wrap
5 times to secure.
Make sure that the position of the x4 Turnbuckles are approximately
at the same height.
TIP: When mounting 1.5” NPT pole mounts or flush mounts the
turnbuckle hooks should be level with the top of ceiling grid.
When mounting an Atdec pole mount (TH-WH-PJ-CM) the hooks
should be approximately 130mm (5”) above the top of the ceiling grid.
Turnbuckle
(x4)
Support
Wire (x4)