Specifications

70
Flat Screen Wall Mount | Full Motion
Installation Instructions
Component Checklist
Hardware
IMPORTANT INFORMATION
! IMPORTANT - Install Telehook Wall Mount as per Installation Instructions.
! Telehook Wall Mount supports Displays weighing up to 35kg (77lbs), with VESA hole configurations:
ÊÊÊÊUÊ
100x100mm (4”x4”) UÊ300x200mm (12”x8”)
UÊ200x100mm (8”x4”) UÊ300x300mm (12“x12”)
UÊ200x200mm (8”x8”) UÊ400x400mm (16”x16”) - using the extensions plates supplied.
! The Manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
TH-2050-VFM
Articulated Arm
VESA plate
Concrete
Anchor (x3)
4mm
Allen Key
M4 Washer (x4) Coach Washer
M8 (x3)
M5 Washer (x4)
M8x16mm / M8x45mm (x4 each)
M4x16mm / M4x25mm (x4 each)
M5x16mm / M5x25mm (x4 each)
M6x16mm / M6x30mm (x4 each)
Coach
Bolt M8 (x3)
Mounting Screws
M4/5 Spacer Bush (x4)
M6/8 Spacer Bush (x4)
Drilling
Guide
TOOLS REQUIRED:
ÊUÊ*ÜiÀÊÀ
ÊUÊ*«ÃÊi>`Ê-VÀiÜ`ÀÛiÀ
ÊUÊ-«ÀÌÊiÛi
ÊUÊxÊ
3
/
16
”) Drill Bit
ÊUÊ£äÊ
3
/
8
”) Masonry Drill Bit
ÊUÊ£ÎÊ
1
/
2
”) Socket Wrench or Shifter
ÊUÊ£{Ê
9
/
16
”) Socket Wrench or Shifter
Step 7. Cable Management
Connect cables to your Display and
route through Cable Clips.
Step 8. Tilt Adjustment
As TFT Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. *ÕLÃi`\ 11.11.09 ©
Installation Complete
,iÛiÊ>LiÊÛiÀÃÊÕÃ}Ê>Ê*«ÃÊi>`Ê-VÀiÜ`ÀÛiÀ]Ê>`ÊÀÕÌi
the cables along the length of the arms. Reattach the Cable Covers
to hold the Cables in place.
Cable Clips
TIP: Leave enough slack in the cables
to allow full movement at the joints.
Your Telehook Wall Mount Articulated Arm installation is complete and ready for use.
Cable Covers
Cable Covers
,ii>ÃiÊÌiÊ>«ÊiÛiÀÊ>`ÊÌÌÊÌi
Display up or down as desired.
Clamp
iÛiÀ
/}ÌiÊÌiÊ>«ÊiÛiÀÊÌÊV
the Display in desired position.
TILT DOWN
TILT UP
LOOSEN
TIGHTEN
PULL
M8 Dome Nut (x4)
Star Washer (x4)
ÝÌiÃÊ*>ÌiÊÊÝÓ® ÝÌiÃÊ*>ÌiÊÊÝÓ®
TIP: If the Clamp Lever is obstructed
pull it outwards to disengage the
rachet mechanism.