Manual

ManualsBrandsAtec ManualsPower suppliersAgilent-6570A Series

Agilent 6570A Series Single-Output,

2000 W DC Power Supplies

Data Sheet

Speed and accuracy for test optimization

This series of 2000 watt DC power

supplies has the exceptional, proven

reliability that test system engineers

look for. It also has the unusual

combination of high efficiency and

low noise operation.

These DC power supplies can be

controlled either from the front panel

or via an analog programming voltage.

When used in a test system, the fast

up and down programming helps

decrease test time. Quickly reacting

protection features, including CV/CC

mode crossover and over-voltage

protection help protect your valuable

assemblies from damage.

Lab-bench use is enhanced by the

fan-speed control, which minimizes

acoustic noise. The extremely low

ripple and noise helps the test engineer

make extremely accurate current and

voltage measurements.

• Front panel and analog control of output voltage and current

• Fast, low-noise outputs

• Fan-speed control to minimize acoustic noise

• Protection features to ensure DUT safety

Summary of content (6 pages)

PAGE 1
Agilent 6570A Series Single-Output, 2000 W DC Power Supplies Data Sheet Speed and accuracy for test optimization • • • • Front panel and analog control of output voltage and current Fast, low-noise outputs Fan-speed control to minimize acoustic noise Protection features to ensure DUT safety This series of 2000 watt DC power supplies has the exceptional, proven reliability that test system engineers look for. It also has the unusual combination of high efficiency and low noise operation.
PAGE 2
Speciﬁcations Specifications (at 0 ° to 55 °C unless otherwise specified) 6571A-J03 6571A 6572A 6573A 6574A 6575A Special order option Number of outputs 1 1 1 1 1 1 GPIB No No No No No No Output voltage 0 to 8 V 0 to 20 V 0 to 35 V 0 to 60 V 0 to 120 V 14 V Output current 0 to 220 A 0 to 100 A 0 to 60 A 0 to 35 A 0 to 18 A 150 A Output ratings Programming accuracy (at 25 °C ± 5 °C) Voltage 0.04% + Current 0.
PAGE 3
Speciﬁcations, continued Specifications (at 0 ° to 55 °C unless otherwise specified) 6571A-J04 6571A-J17 6573A-J03 6573A-J08 6574A-J03 6574A-J07 Special order option Special order option Special order option Special order option Special order option Special order option Number of outputs 1 1 1 1 1 1 GPIB No No No No No No Output ratings Output voltage 10 V 15 V 37.
PAGE 4
Speciﬁcations, continued Specifications (at 0 ° to 55 °C unless otherwise specified) 6575A-J04 6575A-J06 6575A-J07 6575A-J08 6575A-J09 6575A-J11 Special order option Special order option Special order option Special order option Special order option Special order option Number of outputs 1 1 1 1 1 1 GPIB No No No No No No Output ratings Output voltage 160 V 135 V 200 V 100 V 110 V 150 V Output current 13 A 16 A 11 A 22 A 20 A 15 A Programming accuracy (at 25 °C ± 5 °
PAGE 5
Supplemental characteristics for all model numbers Modulation: (Analog programming of output voltage and current) Input signal: 0 to –4 V for voltage, 0 to 7 V for current Input impedance: 30 kΩ or greater DC floating voltage: Output terminals can be floated up to ± 240 VDC from chassis ground Output common-mode noise current: (to signal ground binding post) 500 μA rms, 4 mA peak-to-peak Remote sensing: Up to half the rated output voltage can be dropped in each load lead.
PAGE 6
www.agilent.com www.agilent.com/find/6570 Ordering information The 6570 Series power supplies come with full documentation on CD-ROM. The CD-ROM includes user’s guide, service manual, quick start guide, and application notes Opt 200 174 to 220 VAC, 47 to 63 Hz (Japan only) Opt 230 191 to 250 VAC, 47 to 63 Hz Opt 0L1 Printed user’s guide Opt 0B3 Printed service manual Accessories 1CM003A* Rack mount flange kit 132.6 mm H (3U) – two flange brackets 1CP002A* Rack mount flange and handle kit 132.