Before Use ● This user manual contains proprietary information that is protected by copyright. All rights are reserved. No part of this user manual may be reproduced, photocopied, transcribed, translated or transmitted in whatsoever from without the prior permission of the manufacturer. ● The size and appearance of this monitor may be changed for improvement without notice.
English CE Conformity Notice The Product herewith complies with requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and carries the ‘CE’ mark accordingly.
Unpacking After opening the box, make sure the following items are provided with the monitor. If you find that any of these items is missing or appears damaged, contact your dealer immediately.
Instructions for Safety English ▶ Matters that demand special attention are divided into ‘Warning’ and ‘Caution’, and are detailed a follows. In case of the possibility that a serious injury or death may occur during a violation of the instructions. In case of the possibility that a slight injury or product damage may occur during a violation of the instructions. ● Don’t plug the power adapter into a non-grounding power outlet. ● Never touch the power plug with wet hands.
English ● Keep the power cord from proximity to a heating instrument. The covering material of the cord may melt, causing a fire or electric shock. ● Grasp the power plug at the base to remove it from the wall, and pull firmly but gently. If you yank at the cord, the wire may be broken, causing ignition or heat generation. ● Pull the power cord out when the monitor is not used for a long time, or while you are away.
English ● Don’t block or obstruct the air-flow holes of the monitor. A fire or damage of the monitor may be caused due to an increase in internal temperature. ● Don’t spill liquids such as chemicals, water on the monitor. A fire or electric shock accident may be caused. ● Never disassemble and repair the monitor but trained repair engineers. A fire or electric shock accident may be caused.
English ● Place the monitor on a stable and secure surface. Fall or displacement of the monitor may cause an injury. ● Turn off the monitor and disconnect all cables from the monitor before moving the monitor. ● Be careful with the shock when moving the monitor. ● Don’t scratch or jolt the monitor surface. Damage or failure of the panel may be caused. ● Take hold of the monitor with both hands setting the panel forward.
CONTENTS English Installing the Monitor 1.1 Features …………………………………………………………… 1 1.2 Installing and Removing the Support ……………………………… 2 Installing the Support ……………………………………………………… 2 Removing the Support …………………………………………………… 2 1.3 Monitor Overview ………………………………………………… 3 Front Side …………………………………………………………… 3 Rear Side …………………………………………………………… 4 1.4 Connecting the Peripheral Devices …………………………… 5 Installing the Monitor Driver 2.
1.1 Features Adopt the 15.0 LCD(Liquid Crystal Display) narrow bezel panel which allows you efficient use in a small space due to the slim design with wide screen. AUDIO It gives user an amplified stereo sound through internally installed speakers (2 W).
1.2 Installing and Removing the Support Installing the Support 1 Lay a soft cloth and place the monitor on it with the screen facing downwards. (Take caution not to cause scratches to the LCD display.) Latch 2 Push in the support in the direction of the arrow. (Make sure that the ‘latches’ are fixed to the LCD.) Support Removing the Support 3 While pressing the ‘latches’ on both sides, push the support in the direction of the arrow and remove it.
1.3 Monitor Overview Installing the Monitor This section identifies the name of each component of the monitor and briefly describes the function of each component. Front Side LEFT Button Decreases the value of the selected item. (Decreases the volume without pressing the MENU Button.) TFT LCD Display Displays the current contents of the display.
Rear Side AUDIO IN Connects the audio cable to the LINE OUT jack on the computer or the stereo jack on the camcorder/VTR. AUDIO OUT Connects a set of headphones or external speakers. ANALOG Connector Connects the VGA signal cable to the ANALOG connector on the computer. DC-IN Connects the DC adapter to input the power.
1.4 Connecting the Peripheral Devices 1 Connecting the power Plug into the power outlet at 220V or 110V. (The voltage is set automatically.) DC-IN Jack DC Adapter Power Cord 2 Connecting the computer Connect the ANALOG connector on the computer. ANALOG Connector ANALOG Connector VGA Cable 5 Installing the Monitor Turn off the monitor, computer and other peripheral devices before connecting the monitor and peripheral devices.
3 Connecting Audio Devices Connect the audio cable to the AUDIO IN on the monitor and the LINE OUT on the computer or connect the audio cable (RCA) cable to the AUDIO IN on the monitor and the stereo on the camcorder/TV and connect a set of headphones or external speakers to the AUDIO OUT.
2.1 Installing the Monitor Driver Under Windows This section shows how to install the monitor driver under Windows or Linux by using the monitor driver diskette provided. To install the monitor driver, please refer to your OS in this section. Windows 98/Me 1 2 3 4 5 6 7 Turn on the computer and the monitor. 8 What do you want Windows to do? Insert the monitor driver diskette into the FDD on the computer. Click the Start button on the Windows display and select Control Panel.
Windows 2000 1 2 3 4 5 6 7 8 Turn on the computer and the monitor. Insert the monitor driver diskette into the FDD on the computer. Click the Start button on the Windows display and select Control Panel. Double click the Display icon in the Control Panel window. In the Display Properties window, click the Setting tab and then select Advanced. Select the Monitor tab and click Properties. Click the Driver tab, select the Driver Update button, and then click the Next button.
Windows XP Turn on the computer and the monitor. Insert the monitor driver diskette into the FDD on the computer. Click the Start button on the Windows display and select Control Panel. Double click the Display icon in the Control Panel window. In the Display Properties window, click the Setting tab and then select Advanced. Select the Monitor tab and click Properties. Select the Driver tab, click Update Driver and then click Next.
2.2 Installing the Monitor Driver Under Linux Linux 1 You’d make xf86config file to run X-Window. Your monitor is surely and easily configured with this file. This file will be made as running xf86config. 2 Press Enter in the first and second window after running xf86config file. 3 In third window, we come up with the mouse setting window. 4 Configure it as opt for user system. 5 Next will be the screen for selecting Keyboard. 6 Configure it as opt for user system.
3.1 Selecting and Adjusting the OSD(On Screen Display) Menu You can select the OSD menu in the OSD window by using all the control buttons under the display. To change the current settings or adjust it to what you prefer, please follow these steps. Selecting and Adjusting the OSD Menu MENU UP/DOWN SELECT UP/DOWN (Select the main menu item) MENU SELECT LEFT/RIGHT (Exit the OSD menu window) (Save the modified value) (Select the submenu item) Press the MENU button to open the OSD menu window.
3.2 Exclusive ANALOG Monitor OSD Menus The exclusive ANALOG monitor can use only ANALOG signals as input signals. Main Menu Software Version Screen Resolution Screen Frequency BRIGHTNESS/CONTRAST Controls the brightness and contrast of the display. BRIGHTNESS : Controls the brightness of the display. CONTRAST : Adjusts the level of difference between light and dark areas of the display. EXIT : Exits BRIGHTNESS/CONTRAST menu. COLOR Controls the color(Red, Green, Blue) of the display.
POSITION Adjusts the position of the display. HORIZONTAL : Adjusts the horizontal position of the display. VERTICAL : Adjusts the vertical position of the display. CLOCK : Increases or decreases the number of pixel to adjust the horizontal size. PHASE : Adjusts the focus and clarity of the display. EXIT : Exits POSITION menu. SETUP Controls and selects the OSD position, OSD time and OSD language of the display. OSD POSITION : Adjusts the position of the OSD window.
A.1 Troubleshooting Please check the below particulars before you contact the service center to notify an abnormality of the monitor. The window doesn’t show anything Is the monitor power cord inserted? Please connect the power cord correctly to the concent. Is the power turned off? Please press the power button. Is the power turned on and the power pilot lamp blinking amber? The monitor is in the power saving mode. Please therefore move the mouse or press any key on the keyboard.
A.2 Specification The details of product specification can be changed without notice to improve the product.