Owner's manual
MODEL FREQUENCY VSWR MAXIMUM INPUT FEED SHIELDING
RANGE TYPICAL CW INPUT IMPEDANCE CONNECTOR EFFECTIVENESS
POWER TYPE
RE TESTS
11
11
1
CHARACTERISTIC FREQ
3
250 W
CW CW
CW CW
CW FROM
5405 5405
5405 5405
5405 9 kHz – 5 GHz
≤≤
≤≤
≤ 1.75:1 50
Ω 7/16
DIN PLUG INTERNAL E-FIELDS
RI TESTS
22
22
2
ALL OTHER FREQ 400 W TO N JACK 80 dB MINIMUM
DC – 20 GHz
≤≤
≤≤
≤ 1.3:1 W/ OPT. BLOWER ADAPTER 10 kHz – 1 GHz
GTEM! Models 5405/5407
22
22
2
RF Emissions/Immunity Test Cell
Electrical Specifications
Physical Specifications
MODEL OUTER DOOR HIGHEST ACCURACY APPROX MAXIMUM DISTRIB
CELL DIMENSION TRANSVERSE TEST SURFACE CELL SEPTUM LOAD
DIMENSION IN CENTER OF CELL
4
WEIGHT HEIGHT
5
RATING
6
Options
Custom Electrical Filters
Custom Feedthrough Panels
EUT XYZ Axis Positioning Device
EUT Illumination
Forced Ventilation
High Power Configuration
TM
Note:
The 5405 is shipped fully assembled. Please note dimensions
in the Physical Specifications table to ensure the unit will fit
through your doorways. As standard, the 5407 is shipped partially
assembled with instructions for installation. Doorways that are
218.5 cm (86 in) wide and 203.2 cm (80 in) high are needed for
subassembly passage. If space limitations exist, the unit can be
shipped unassembled. Contact EMCO sales department regarding
requests to ship the unit unassembled and for supervision of
installation.
(L) 3.0 m (9.8 ft) 250 kg 550.0 mm 250 kg
5405 (W) 1.6 m (5.2 ft) (W) 460 mm (18.1 in) (W) 300 mm (11.8 in) (551 lb) (21.7 in) (551 lb)
(H) 1.7 m (5.6 ft) W BASE (H) 385 mm (15.2 in) (H) 300 mm (11.8 in)
(H) 1.1 m (3.7 ft) W/O BASE
(L) 4.0 m (13.10 ft) 500 kg 900.0 mm 430 kg
5407 (W) 2.2 m (7.1 ft) (W) 686 mm (27.0 in) (W) 400 mm (15.8 in) (1100 lb) (35.4 in) (950 lb)
(H) 2.1 m (6.8 ft) W BASE (H) 747 mm (29.4 in) (H) 400 mm (15.8 in)
(H) 1.4 m (4.6 ft) W/O BASE
Model 5407
1
Frequency range where OATS correlation demonstrated:
3-position algorithm 30 MHz - 5 GHz, 9-position
algorithm 9kHz - 5 GHz
2
Low VSWR to f ≥ 20 GHz; subject to field uniformity
tolerance
3
Characteristic frequency: resistor board/RF absorber
crossover frequency
4
≤ 8 dB Uniformity
5
At resistor board junction
6
Total EUT and personnel load distributed at maximum
loading of 450 kg/m
2
. Point loads less than 7 cm
2
should
not exceed 20 kg/cm
2
.
RE TESTS
11
11
1
CHARACTERISTIC FREQ
3
200 W
CW CW
CW CW
CW FROM
5407 5407
5407 5407
5407 9 kHz – 5 GHz
≤≤
≤≤
≤ 1.75:1 50
Ω 7/16
DIN PLUG INTERNAL E-FIELDS
RI TESTS
22
22
2
ALL OTHER FREQ 500 W TO N JACK 80 dB MINIMUM
DC – 20 GHz
≤≤
≤≤
≤ 1.3:1 W/ OPT. BLOWER ADAPTER 10 kHz – 1 GHz
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
2/00 - 1k S © 2000 ETS-EMCO REV-A2/00 - 1k S © 2000 ETS-EMCO REV-A
2/00 - 1k S © 2000 ETS-EMCO REV-A2/00 - 1k S © 2000 ETS-EMCO REV-A
2/00 - 1k S © 2000 ETS-EMCO REV-A
USA:
Tel +1.512.835.4684
Fax +1.512.835.4729
FINLAND:
Tel +358.2.8383.300
Fax +358.2.8651.233
ONLINE:
info@emctest.com
http://www.emctest.com