LIBRA-02 P PORTABLE COPY ROUTER USER’S MANUAL 1 Operating and Safety Instructions
CONTENTS Page 1. General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine’s Description and Purpose of Use 3 2.1. Machine’s description 3 2.2. Technical features 5 2.3. Overall dimensions 6 2.4. Part lists and technical drawings 7 2.5. Wiring diagram 9 3. Safety 10 3.1. Safety information 10 3.2. Accident prevention 10 3.3. General safety information 11 4. Transport of the machine 13 5. Installation of the machine 13 5.1. Preparation 13 5.2.
1. GENERAL INFORMATION 1.1. INTRODUCTION The user’s manual given by the manufacturer contains necessary information about the machine parts. Each machine operator should read these instructions carefully, and the machine should be operated after fully understanding them. Safe and efficient use of the machine for long term depends on understanding and following the instructions contained in this manual. The technical drawings and details contained in this manual constitute a guide for the operator. 1.2.
Please mention the below mentioned data in all your correspondence regarding the machine with the manufacturer and/or your ATECH dealer.
2.2.
2.3.
2.4. TECHNICAL DRAWINGS and PART LISTS NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 19 21 22 24 28 29 30 31 32 35 36 37 38 40 41 42 43 44 45 46 47 48 49 63 68 ORDER NO.
3 13 14 15 16 17 23 24 25 26 27 33 34 39 51 52 53 54 55 57 65 66 67 69 71 73 Figure-3 8 Operating and Safety Instructions ORDER 550-010 177-03 172-012 223-004 141-071 141-068 141-072 172-013 172-017 111-074 550-014 111-059 192-006 144-003 111-054 144-004 111-068 145-017 141-175 141-136 141-062 141-063 550-011 176-014 191-001 141-061 PART NAME HANDLE 3 DIA 6 mm WASHER M6x20 HEXAG. SCREW BAKALITE LEVER A5-12 SWITCH HANDLE BOLT UPPER LIMITING PIN SNAP HOUSING SHEET M6x10 HEXAG. SCREW M6x30 HEXAG.
2.6.
3. SAFETY 3.1. SAFETY INFORMATION The symbols shown hereunder are necessary to be read with special attention. Not reading or observing of them may cause damage to the equipment or personal injury IMPORTANT The IMPORTANT symbol above is one telling to apply special care and to be careful at carrying out the specified operation. CAUTION ! The CAUTION! Symbol above warns you against specific dangers, and requires to read the text. Not observing may cause damage to the equipment.
3.2.3 Before starting to work with the machine, the operator should check the features of the machine, learn all details of the machine's operation. 3.2.4 The machine should be operated only by staff members, who have read and understood the contents of this manual. 3.2.5 All directives, recommendations and general safety rules contained in this manual have to be observed fully. The machine cannot be operated in any way for purposes other than those described herein.
3.3.7. Use correct illumination for the safety of the operator. (ISO 8995-89 The Lighting of Indoor Work Systems) 3.3.8. Don't leave anything on the machine. 3.3.9. Don’t use any materials other than those recommended by the manufacturer for cutting operations on the machine. 3.3.10. Ensure that the work piece is clamped appropriately by the machine's clamp or vice. 3.3.11. Ensure safe working position, always keep your balance. 3.3.12. Keep your machine always clean for safe operation.
4. TRANSPORT OF THE MACHINE IMPORTANT 4.1.1. The transport should be done by qualified personnel only. 4.1.2. The machine should be transported by lifting with proper equipment (not touching the ground during the transport). 4.1.3. Movable parts on the machine should be fixed before carrying out the transport through the support shaft fixing bushing (Figure-5, No. 36). 4.1.4. Please keep the original packing of the machine for use at future transports. 5. INSTALLATION OF THE MACHINE 5.1. PREPARATION 5.1.
5.2. ELECTRIC CONNECTION 5.2.1The electric cable socket has to be in accordance with the socket on the machine. 5.2.2 Your machine has to be used with 230V 50Hz voltage. 5.2.3 Use the machine’s plug with a grounded socket. CAUTION ! 5.2.4. Check the supply voltage. The source voltage must be in accordance with the data on the machine’s label. 6. MACHINE’S SAFETY INFORMATION 6.1.1. The machine should not be used without the transparent protection shield in front of the router bit. 6.1.2.
7. OPERATION 7.1. BEGINNING OF THE WORK 7.1.1. Ensure that the machine table and all kind of parts are clean and dry. Degrease and dry the machine table. Especially ensure that the holding grips and handles are clean and dry. 7.1.2. Clean all surfaces of the machine from chip and foreign particles. Use eye glasses for protection. 7.1.3. Check with the appropriate keys that the router bit is tightened properly. 7.1.4. Check the router bit for wear, bending and breaking. Replace them if damaged. 7.1.5.
8. CHANGING THE ROUTER BIT 8.1.1 If it becomes necessary to replace the router bit for any reason, follow the following order for replacement: 8.1.2. Unplug the machine 8.1.3. Loosen the nut shown in Figure 4, No. 52 and 51, using 2 wrench keys 14 and 17 mm, turning it in counter clockwise direction. Take out the router bit from its holder. Insert the new router bit into the router bit holder, and tighten the nut. NOTE: Ensure that the router bit is fixed properly. CAUTION ! 8.1.4.
9. MAINTENANCE 9.1. PERIODIC CHECKS AND MAINTENANCE AT THE END OF THE WORKING DAY 9.1.1. Unplug the machine first. 9.1.2. Remove all burr, foreign materials from the machine’s surface. Use protective eye glasses. 9.1.3. Clean and dry the machine table. 9.1.4. When cleaning the machine, don’t use any materials which could cause damage to the machine’s paint. 10. INFORMATION ABOUT FAULTY USE 10.1.1. Check the plug for power supply. 10.1.2.