Quick Start Guide J Series by ATEL About your J-Series CPE The J-Series ODU (Outdoor Unit) is specially designed to be installed outside (like on a roof) over the pole or a wall. That helps ODU to receive better 4G-LTE signals and feed them into the home or internal living space via an Ethernet cable using the POE feature. 4 5 6 7 4G LTE Outdoor CPE 3 Model: AOL-J912 4G LTE Bands 2/4/5/12/13/14/25/26/66 2 1 Figure 1. LEDs & Ports Location Version 2.
Device Ports & LED Interface PWR (Power) Ethernet RJ45 Port 1 Receive Power & connect with your computer over Ethernet via PoE. Package Contents 5 Power LED. LED On indicates the device is turned on. LED Off indicates that the device is powered off. • J-Series ODU Unit • Installation Kit Mounting Bracket #2 Phillips Head Screws x4 Reset Button 2 Pressing this button helps device configurations convert to factory defaults. Regular (2FF) SIM card needs to be inserted as directed. Ethernet LED.
Installation Kit • Mounting Bracket • U-bolt Clamp Set Helps to affix the ODU with the mounting bracket to a pole. Towards Pole/Wall Towards ODU rear panel NOTE: Tools not included in the installation kit. • #2 Phillips Head Screw x4 PoE Injector + Power Cord Input 100-240V AC • M6 Nut x4 Output 48-56V DC Helps to attach mounting bracket to ODU rear panel.
Setting up your J-Series ODU Power ON your J-Series ODU Install the SIM Card & Connect the Ethernet Cable • 1. Unscrew the covers from the SIM card slot and Ethernet LAN port on the bottom panel. 2. This ODU device is designed to connect to a 4G LTE network. Kindly ensure that you have an active LTE SIM card from your service provider. • • To turn on your device, you need to connect the Ethernet cable coming from the ODU to the PoE injector‘s P+D/OUT Port.
Installation of your J-Series ODU 1. 2. Place the ODU outside and facing an open area towards an eNodeB/ Cell Tower. Obstructions such as concrete walls, glass partitions or wooden walls affect the transmission and reception of network signals. Keep the ODU away from household electrical appliances that produce strong electric or magnetic fields such as dish satellite antennas. 2. Attach the U-shaped side of the bracket to the pole using the provided U bolt clamps.
Affix/Align Mounting Brackets To Mount on a Wall Note: Wall Mount tools and installation kit items are not included. Use four screws to attach the mounting bracket to the rear panel of the ODU. If required, use screws used to stack two mounting brackets together, allowing the ODU CPE’s angle to be adjusted horizontally or vertically. Fix Mounting Bracket to the Wall Place the U-shaped mounting bracket against the wall in the desired position and mark the location for holes. 2.
Online Device Management Portal Installation Completion Once the installation is complete and the ODU CPE is connected to your Computer/PC using the PoE injector. You can now access data services on that Computer/PC. Make sure all LEDs are lit up on the ODU. Your installation should resemble the images below.
Optional Add-On’s: Indoor WiFi AP Unable to Access Internet? To bring LTE High Speed data connection to share with multiple devices over LAN or WiFi, simply connect the JSeries ODU with our indoor WiFi AP (built-in POE). You can contact us to learn more about the ATEL Indoor WiFi AP on our website, https://www.atel-usa.com/. 1. If you are using other cables or devices that are compatible with our AOL-J ODU, please refer to their user manual to connect with our ODU for data services over the LTE Network.
Disclaimer: Certain variations may be present between the device and user manual description depending on software release or specific network services. ATEL shall not be held legally responsible for such deviations, if any, nor for their potential consequences. Data plan may be required. Coverage subject to network availability. Limited Warranty: The full ATEL USA Warranty Policy can be found at www.atelusa.com/warranty.
