%L0WURQLFV#$XWR 6ZLWFK 50LQ#402XW 40LQ#50RXW 8VHU¶V#0DQXDO $)0475 $)0574
Introduction Features Installation 2 to 1 mode 1 to 2 mode (AF-142 Only) Specifications Operation 2 to 1 mode (AF-241 and AF-142) Auto mode Manual mode File Transfer mode 1 to 2 mode (AF-142 ONLY) Selecting the printer manually Selecting the printer through software controls Products in the Bi-tronics Auto Switch Series Troubleshooting LED locks on the PORT when a cable is connected The Printer status window shows “Printer not Responding” “Printer not Connected” Error messages show up while, or immediately
,QWURGXFWLRQ The AF-142 is a Bi-tronics Auto Switch that will operate in either, one computer to two printers mode, or two computers to one printer mode, called respectively 1 to 2 mode and 2 to 1 mode. The AF-241 Bi-tronics Auto Switch is only capable of operating only in 2 to 1 mode. These switches operate in 2 to 1 mode without software drivers and deliver print jobs to the printer on a first come, first served basis.
,QVWDOODWLRQ 2→ 1 mode (For AF-241 and AF-142) 1. 2. 3. 4. 5. 6. Turn the power to all devices to be attached to the Auto Switch. Connect the Bi-tronics Auto Switch to your computer by using a straight through DB-25 male to male cable. Connect the Bi-tronics Auto Switch to the parallel devices by cables with one DB-25 to C-36 male to male cable.
6SHFLILFDWLRQV UNIT TYPE → ↓Function Mode → AF-142 1→2 Power Consumption AF-241 2→1 2→1 9V DC 50 mA(max.) Cable Length 6m or 20 ft.
File Transfer Mode: When you are using the AF-241 or the AF-142 in 2 to 1 mode you are able to activate the File transfer mode of these devices. You select file transfer mode by pressing the button on top of the unit until both LED’s are constantly on. By activating the file transfer mode you will be able to not only share files, but peripherals as well. However, you will need some additional software assistance such as Interlnk/Intersrv of DOS, or FastLynx of Rupp Corp.
URXEOHVKRRWLQJ IMPORTANT: Before beginning any of the following troubleshooting proceedures please check for properly connected cables, if the cables appear to be connected correctly then remove the Auto Switch from the system and connect the printer directly to the computer with both cables if possible (one cable at a time). LED locks on the PORT when a cable is connected: • The Bi-tronics Auto Switch may receive some errant signals that begin a “timeout” count.
Error messages show up while, or immediately after you install new printer drivers. • Uninstall other bi-directional printer status windows before installing a new one. 1. In Windows 95 push the Start button, select settings, select printers. 2. Find the correct printer Icon and double left-click on the Icon. 3. Activate the Printer pull-down menu and select Properties. 4. Across the top of the Printer Properties window there are several tabs select the Details tab. 5.
3UHYHQWLQJ#5DGLR#)#79#,QWHUIHUHQFH WARNING!!! This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. This equipment has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
)&RWLFH This device complies with Part 15 of FCC rules. Operation of this device is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation.
