©1999 ATEN Technology, Inc. All Rights Reserved. Microsoft and Windows 98 are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines, Inc. Macintosh, G3/G4 and iMac are registered trademarks of Apple Computer, Inc. ATEN is a registered trademark of ATEN Technology, Inc. IOGEAR is a registered trademark of ATEN Technology, Inc. ATEN Technology makes no warranty of any kind with regards to the information presented in this document.
Packing List The complete IOGEAR MiniView package consists of: TM • • • • One MiniView KVM switch Two or four sets of custom cables, depending on the model. G-CS12 comes with two cables while G-CS14 comes with four. One User Manual One Quick-Start Setup Guide TM Note: If your computers use AT keyboard connectors, please contact us for a free set of PS/2-AT adapters. Please check to make sure that all components are included and nothing is damaged.
Contents Introduction ……...…………...……... 01 Features ………………………………... 02 Hardware Requirements …………… 03 Installation …………………..………… 04 Operation ………………………….……. 06 Manual Port Selection HotKey Port Selection …………….………. 07 Auto Scan Mode ………………………….... 08 Next/Last Mode ……………………….……. 09 Appendix A ……………………………… 10 Specifications Appendix B ……………………………… 11 Troubleshooting Appendix C ………………………………. 12 Contacting IOGEAR Appendix D ……………………………….
Introduction Thank you for purchasing one of the smallest and most feature-rich KVM switches on the market. IOGEAR’s KVM switches are first-rate connectivity accessories designed to help reduce the frustration of managing multiple computer systems. With the MiniView series by IOGEAR, you can access multiple computers from a single console (keyboard, mouse and monitor). The MiniView provides two convenient methods to access connected computers.
Features Supports Microsoft IntelliMouse, Logitech MouseMan+, FirstMouse+, IBM Scroll Point Mouse and many others Keyboard and mouse emulation for error free PC booting Hot pluggable – add or remove connected PCs without powering off the MiniView TM Full Plug-n-Play monitor support Caps Lock, Num Lock and Scroll Lock status is saved and restored when switching ports Supports video resolutions up to 1920 x 1440 Easy installation - no software required Built-in Auto Scan Mode Uses standard connectors to c
Hardware Requirements Console One VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any PC in the installation One PS/2 mouse One PS/2 keyboard or One AT keyboard w/ a PS/2 keyboard adapter PC The following equipment must be installed on each PC that is to be connected to the system: One VGA, SVGA or Multisync video card One PS/2 mouse port One PS/2 or AT keyboard port * See the note under Cables in the next section.
Installation Installation Before you begin, make sure that the computers you’re going to connect to the MiniViewTM are turned off. 4 1 Plug the monitor, keyboard, and mouse into the console port connectors of the MiniViewTM unit. 2 Use the extender cables (as described in the Hardware Requirements and Unpacking sections) to connect the monitor, keyboard and mouse ports of the PCs to the MiniViewTM CPU ports, as shown in the diagram to the right.
Installation Installation... Installation...
Operation Controlling the PCs in your MiniViewTM configuration from a single console couldn’t be easier. Two port selection methods provide instant access to any attached PC: Manual Port Selection Hot Key Port Selection Note: When powering-on, the MiniViewTM switches to port 1 by default. If the PC attached to port 1 is inactive, the monitor will be blank so it may appear as if the unit is not functioning. This is not the case.
Operation... Operation... Hot Key Port Selection Hot Key navigation allows you to select the active PC directly from the keyboard, instead of having to manually select it by pressing the Port Selection button.
Operation... Auto Scan Mode: The Auto Scan feature automatically switches between the connected PCs at regular intervals so that you can monitor their activity without having to take the trouble of switching yourself. To invoke Auto Scan Mode, key in the following Hot Key combination: 2-Port MiniViewTM: Press and release the Left Shift key, then press and release the Right Shift key (Left Shift + Right Shift). Once scanning begins, it continues until you press the [Spacebar] to exit Auto Scan Mode.
Operation... Operation... Next/Last Mode: The Last/Next feature is provided to enable you to quickly switch back and forth between computers in order to monitor them manually, instead of using Auto Scan Mode. This method lets you monitor a particular computer for as long or as little as you like - as opposed to Auto Scan Mode, which switches after a fixed interval. To invoke Last/Next Mode, key in the following Hot Key combination: 1. Press and release Ctrl + Alt + Shift 2. Press and release 9 3.
Appendix A Specifications: Port Selection Hot Keys /Port Selection Button Keyboard: PS/2 & AT Mouse: PS/2 Keyboard: 6-pin mini-DIN (F) Emulation LEDs Console Connectors PC Connectors Port-Selected Mouse: 6-pin mini-DIN (F) Monitor: HDB-15 VGA (F) Keyboard: 6-pin mini-DIN (F) Mouse: 6-pin mini-DIN (F) Monitor: HDB-15 VGA (F) Video Resolution Max: 1920 x 1440, DDC2B AutoScan Interval L E D A c tiv ity Power Consumption O ff Housing 3 seconds O n ( s t eTemperature ady) Operating M
Appendix B Troubleshooting: Note: If you are experiencing any erratic behavior from your MiniViewTM, first make sure there are no problems with the cables and that they are all properly connecetd. Problem The keyboard is not responding. Possible Cause Action The keyboard needs to be reset. Disconnect the keyboard from the MiniViewTM, wait a few seconds and plug it back in. The MiniViewTM needs to be reset. Shut down the computers and disconnect the keyboard from the MiniViewTM.
Appendix C Contacting IOGEAR In the event that your MiniViewTM fails to function properly, or you wish to contact us for any other reason, here are a few ways to contact us. IOGEAR 16560 Aston Street Irvine, CA 92606 Phone: (949) 250-1260 Toll Free: (888) 999-2836 Fax: (949) 250-1262 Appendix C www.iogear.com info@iogear.
Appendix D Radio & TV Interference Statement This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IOGEAR 16560 Aston Street Irvine, CA 92606 Phone: (949) 250-1260 Toll Free: (888) 999-2836 Fax: (949) 250-1262 www.iogear.com info@iogear.
IOGEAR 16560 Aston Street Irvine, CA 92606 Phone: (949) 250-1260 Toll Free: (888) 999-2836 Fax: (949) 250-1262 www.iogear.com info@iogear.
©1999 ATEN Technology, Inc. All Rights Reserved. Microsoft and Windows 98 are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines, Inc. Macintosh, G3/G4 and iMac are registered trademarks of Apple Computer, Inc. ATEN is a registered trademark of ATEN Technology, Inc. IOGEAR is a registered trademark of ATEN Technology, Inc. ATEN Technology makes no warranty of any kind with regards to the information presented in this document.
Package Contents This IOGEAR package contains: G-CV160 Mac – PS/2 Adapter ADB Patch Cable Mac Video Patch Cable User Manual & Setup Guide Product Registration / Warranty Card Please check to make sure that all components are included and nothing is damaged. If you discover a problem, please contact your dealer.
Contents Introduction ……...…………...……... 01 Features / Sys. Requirements …… 02 Installation ……………………..……… 03 KVM Setup ………………………………….. Non-KVM Setup ………...………….………. 04 Connection Diagrams …………………….... 05 Dip Switches ….………………………… 06 Video Keyboard & Mouse 07 Mac Key Assignments …………….… 08 Specifications …………………….….… 09 Radio Interference / Warranty ...… 10 Contacting IOGEAR ..………………….
Introduction Thank you for purchasing IOGEAR’s MiniViewTM Mac Adapter, a Macintosh-PS/2 converter that allows seamless integration of a Macintosh computer into your existing KVM configuration. Our Mac Adapter is fully compatible with older Macintosh systems, the new iMac, G3 and G4. Full Macintosh keyboard functionality is supported on any PS/2 keyboard, while a second ADB port allows your existing ADB devices to be used with the Mac.
Features / System Requirements Features Converts from ADB and DB-15 to PS/2 and HDB-15 Allows a Macintosh system to be incorporated into your KVM setup. Secondary ADB port provides support for additional Macintosh accessories. Full Mac functionality supported on a PS/2 keyboard No software required. Patented VSE technology supports ultra high quality video at resolutions up to 1920 x 1440. Save time, space and money. 3 Year Limited Warranty.
Installation Installation in a KVM setup: Before installing your G-CV160, please make sure your Macintosh is powered OFF. 1) Connect the PC keyboard and mouse ports on the G-CV160 to one of the PC ports on your KVM switch. Be sure the keyboard port on the KVM switch is connected to the keyboard port on the G-CV160, and the same is true for the mouse ports.
Installation Before installing your G-CV160, please make sure your Macintosh is powered OFF. Installation without a KVM switch: 1. Connect your PS/2 keyboard and mouse to the PC ports on the G-CV160. 2. If you have an older Macintosh with DB-15 (Mac video) connectors, connect your monitor to the PC video port on the GCV160.
Installation 5
Dip Switches Note: Do not modify the DIP Switches when your Macintosh is powered-ON. Switches 1-6 are used to set the appropriate video properties for your configuration. *1 – When SW5 and SW6 are both ON, the VGA and SVGA resolution settings are selected in the monitor portion of the control panel.
Dip Switches Switch 7 is used to toggle between a standard 101 and 104 key keyboard. Switch 8 toggles the mouse between high and normal speed settings.
Mac Key Assignments 8
Specifications 9
Radio Interference / Limited Warranty Radio & TV Interference Statement This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Contacting IOGEAR In the event that your MiniViewTM fails to function properly, or you wish to contact us for any other reason, here are a few ways to contact us. IOGEAR 16560 Aston Street Irvine, CA 92606 Phone: (949) 250-1260 Toll Free: (888) 999-2836 Fax: (949) 250-1262 www.iogear.com info@iogear.
