DVI KVM Extender CE600 / CE602 User Manual www.aten.
CE600 / CE602 User Manual EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE600 / CE602 User Manual User Information Online Registration Be sure to register your product at our online support center: International http://support.aten.com North America http://www.aten-usa.
CE600 / CE602 User Manual Package Contents The CE600 / CE602 package consists of: 1 CE600L / CE602L DVI KVM Extender (Local Unit) 1 CE600R / CE602R DVI KVM Extender (Remote Unit) 1 1.8 m USB DVI-D Single Link KVM Cable Set (CE600) 1 1.8 m USB DVI-D Dual Link KVM Cable Set (CE602) 2 Power Adapters 1 Mounting Kit 1 User Instructions* Check to make sure that all the components are present and that nothing got damaged in shipping. If you encounter a problem, contact your dealer.
CE600 / CE602 User Manual Contents FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Online Registration . . . . . . .
CE600 / CE602 User Manual Appendix Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 International . . . . . . . . . . . . . . . . . . . . .
CE600 / CE602 User Manual About this Manual This User Manual is provided to help you get the most from your system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below. Chapter 1, Introduction, introduces you to the CE600 / CE602 system. Its purpose, features and benefits are presented, and its front and back panel components are described.
CE600 / CE602 User Manual Conventions This manual uses the following conventions: Monospaced [] Indicates text that you should key in. Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. 1. Numbered lists represent procedures with sequential steps. ♦ Bullet lists provide information, but do not involve sequential steps.
Chapter 1 Introduction Overview The CE600 / CE602 is a DVI and USB based KVM Extender with RS-232 serial functionality. It allows access to a computer system from a remote console (USB keyboard, monitor, and mouse).
CE600 / CE602 User Manual Features Local and Remote Units connect at distances up to 60 m using Cat 5e cable Allows access to a computer or KVM installation from a remote console (up to 60m) Control your system from the remote console (USB keyboard, USB mouse and DVI interface monitor) Supports DVI-D interface and allows transmission of DVI dual-link signals (CE602) Features ATEN technology that allows A/V transmission over one Cat 5e cable Enable HDCP, RS-232, microphone and dual link signals
Chapter 1. Introduction Requirements Consoles A DVI single link or dual link monitor capable of the highest resolution you will be using on any monitor in the installation.
CE600 / CE602 User Manual Operating Systems Supported operating systems are shown in the table, below: OS Windows Linux 4 Version 2000, 2003, 2008, XP, Vista, 7 RedHat 9.0 and higher SuSE 10 / 11.1 and higher Debian 3.1 / 4.0 Ubuntu 7.04 / 7.10 UNIX FreeBSD 5.5 / 6.1 / 6.2 Novell Netware 6.
Chapter 1. Introduction Components CE600L / CE602L (Local Unit) Front View 1 2 3 4 1 No. Component 5 2 Description 1 DVI port Connect a DVI cable from a computer to this port. 2 USB Type B Input The USB cable from your computer or USB hub plugs in here. 3 Audio Ports These mini stereo ports are for the speakers (green) and microphone (pink). 4 RS-232 Serial Port Connect the RS-232 cable from your computer into this port.
CE600 / CE602 User Manual CE600R / CE602R (Remote Unit) Front View 1 2 3 1 No. 6 Component Description 1 EQ Switch Use this to adjust the video quality of the remote console. 2 RS-232 Serial Port RS-232 serial devices – such as touchscreens or barcode scanners – plug into this port. 3 LEDs The CE602R has two LEDs to indicate operating status. See page 18 for full details.
Chapter 1. Introduction CE600L / CE602L (Local Unit) Rear View No. 1 Component F/W Upgrade Switch Description Use this switch to turn on the firmware upgrade mode. Reset the power to proceed with the firmware upgrade. Switch it off and reset the power to return to normal mode. 2 Power Jack The cable from the DC Power adapter connects here. 3 Sub / Main The Cat 5e cable that connects the Remote and Local Units plugs in here.
CE600 / CE602 User Manual CE600R / CE602R (Remote Unit) Rear View 2 1 No. Component 3 5 4 Description 1 Power Jack The cable from the USB Power adapter connects here. 2 USB The USB cable for your keyboard / mouse plugs in here. 3 Audio Ports These mini stereo ports are for the speakers (green) and microphone (pink). 4 Sub / Main The Cat 5e cable that connects the Remote and Local Units plugs in here.
Chapter 2 Hardware Setup 1. Important safety information regarding the placement of this device is provided on page 25. Please review it before proceeding. 2. Make sure that the power to all devices connected to the installation are turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. Rack Mounting For convenience and flexibility, the CE600 / CE602 can be mounted on system racks. To rack mount a unit do the following: 1.
CE600 / CE602 User Manual 2. Screw the bracket into any convenient location on the rack. Note: These screws are not provided. We recommend that you use M5 x 12 Phillips Type I cross, recessed type screws.
Chapter 2. Hardware Setup Installation Grounding To prevent damage to your installation it is important that all devices are properly grounded. 1. Use a grounding wire to ground both units by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object. 2. Make sure that the computer that the Local Unit connects to and the monitor that the Remote Unit connects to are properly grounded.
CE600 / CE602 User Manual 3. For increased grounding protection, use STP (shielded twisted pair) cable to connect the Local and Remote Units. There are two methods that can be used: a) In addition to the eight paired wires, STP cable also contains a grounding wire. Solder this wire to the RJ-45 connector as shown in the diagram below: b) The second method is to use the STP cable shielding for grounding.
Chapter 2. Hardware Setup Setting Up Setting up the CE600 / CE602 DVI KVM Extender system is simply a matter of plugging in the cables. Make sure that all the equipment to be connected up is powered Off. Refer to the installation diagram on the following page and do the following: 1. Plug the appropriate connectors on the DVI KVM cable supplied with this unit into their ports on the front of the Local Unit (CE600L / CE602L). 2.
CE600 / CE602 User Manual Installation Diagrams Front View 3 1 DVI KVM cable 2 14 Local PC
Chapter 2. Hardware Setup Rear View 4 CE600L / CE602L 5 Cat 5e cables 4 CE600R / CE602R 7 6 Note: 1. The serial port on the CE600L / CE602L connects to the computer; the serial port on the CE600R / CE602R (not shown) connects to a serial device (optional). 2. The illustration above shows a Dual Link DVI installation where both Cat 5e cables are used (CE602 only).
CE600 / CE602 User Manual This Page Intentionally Left Blank 16
Chapter 3 Operation Picture Adjustment Use the EQ switch to adjust the equalization strength and improve a blinking image. The values range from 0-7 where: 7: strongest equalization 0: weakest equalization LED Display The CE600 / CE602 Local and Remote Units have front panel LEDs to indicate their operating status, as shown in the tables, following: CE600L / CE602L (Local Units) LED Link (Green) Indication Lights steadily to indicate that the connection to the Remote unit is ok.
CE600 / CE602 User Manual CE600R / CE602R (Remote Unit) LED Link (Green) Indication Lights steadily to indicate that the connection to the Local Unit is ok. Flashes when there is a problem with the connection to the Local Unit. Power (Green) 18 Lights steadily to indicate that the Remote unit is receiving power.
Chapter 4 The Firmware Upgrade Utility The Windows-based Firmware Upgrade Utility (using the file name CE600_602_ATEN_v1.x.xxx.exe) provides a smooth, automated process for upgrading the KVM switch's firmware. The Utility comes as part of a Firmware Upgrade Package that is specific for each device. New firmware upgrade packages are posted on our web site as new firmware revisions become available. Check the web site regularly to find the latest packages and information relating to them: http://www.aten.
CE600 / CE602 User Manual 5. In the Local Unit’s rear panel, turn the FW Upgrade switch On. This enables both the Local and Remote Units to operate in Firmware Upgrade Mode when the Local Unit is powered on again. CE600L / CE602L 4 5 Cat 5e cable Switch ON Firmware Upgrade CE600R / CE602R 4 6. Plug in the Local Unit’s power adapter to power it on.
Chapter 4. The Firmware Upgrade Utility Starting the Upgrade To upgrade your firmware: 1. Run the downloaded Firmware Upgrade Package file – either by double clicking the file icon, or by opening a command line and entering the full path to it. The Firmware Upgrade Utility Welcome screen appears: Note: The screens shown in this section are for reference only. The wording and layout of the actual screens put up by the Firmware Upgrade Utility may vary slightly from these examples. 2.
CE600 / CE602 User Manual 3. Click Next to continue. The Firmware Upgrade Utility main screen appears: The Utility inspects your installation. The Local and Remote Units are listed in the Device List panel and automatically selected for upgrade. 4. Click Next to perform the upgrade. If you enabled Check Firmware Version, the Utility compares the device's firmware level with that of the upgrade files.
Chapter 4. The Firmware Upgrade Utility Upgrade Succeeded After the upgrade has completed, a screen appears to inform you that the procedure was successful: 1. Click Finish to close the Firmware Upgrade Utility. 2. After successfully upgrading the firmware, unplug the Local unit’s power adapter. 3. Turn the FW Upgrade switch Off to exit the Firmware Upgrade Mode for both Local and Remote Units. 4. Plug in the Local unit’s power adapter to turn it on.
CE600 / CE602 User Manual This Page Intentionally Left Blank 24
Appendix Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation.
CE600R / CE602R User Manual If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or un-interruptible power supply (UPS).
Appendix Rack Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack. Always load the rack from the bottom up, and load the heaviest item in the rack first. Make sure that the rack is level and stable before extending a device from the rack.
CE600R / CE602R User Manual Technical Support International For online technical support – including troubleshooting, documentation, and software updates: http://support.aten.com For telephone support, Telephone Support, page iii North America Email Support Online Technical Support support@aten-usa.com Troubleshooting Documentation Software Updates Telephone Support http://www.aten-usa.
Appendix Specifications Function Connectors Console Ports KVM Ports CE600L / CE602L CE600R / CE602R Keyboard N/A 1 x USB Type A Female (White) Video N/A 1 x DVI-D Female (White) Mouse N/A 1 x USB Type A Female (White) Speakers N/A 1 x Mini Stereo Jack Female (Green) Mic. N/A 1 x Mini Stereo Jack Female (Pink) 1 x DVI-D Female (White) N/A Speakers 1 x Mini Stereo Jack Female (Green) N/A Mic.
CE600R / CE602R User Manual Troubleshooting Operation problems can be due to a variety of causes. The first step in solving them is to make sure that all cables are securely attached and seated completely in their sockets. Problem Action No video Make sure that all cables are securely plugged into their sockets. Poor quality video The video quality can be improved by adjusting the EQ switch on the CE600R / CE602R to increase or reduce the video signal compensation.
