USB 2.0 DVI KVM Extender CE610 User Manual www.aten.
CE610 User Manual FCC Information This is an FCC Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE610 User Manual User Information Online Registration Be sure to register your product at our online support center: International http://eservice.aten.
CE610 User Manual Package Contents The CE610 package consists of: 1 CE610L USB 2.0 DVI KVM Extender (Local Unit) 1 CE610R USB 2.0 DVI KVM Extender (Remote Unit) 1 Custom DVI 1.8 m Cable 1 1.8 m USB Cable 2 Power Adapters 1 Mounting Kit 1 User Instructions* Check to make sure that all the components are present and that nothing got damaged in shipping. If you encounter a problem, contact your dealer.
CE610 User Manual Contents FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Online Registration . . . . . . . . . . .
CE610 User Manual About this Manual This User Manual is provided to help you get the most from your system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below. Chapter 1, Introduction, introduces you to the CE610 system. Its purpose, features and benefits are presented, and its front and back panel components are described.
CE610 User Manual Conventions This manual uses the following conventions: Monospaced Indicates text that you should key in. [] Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. 1. Numbered lists represent procedures with sequential steps. ♦ Bullet lists provide information, but do not involve sequential steps.
Chapter 1 Introduction Overview The CE610 USB 2.0 DVI KVM Extender supports HDBaseT technology and uses only one Cat 5e cable to extend DVI and USB signals up to 100 m. The CE610 is equipped with USB connectors which allow you to extend any USB device between the units. The USB functionality provides not only peripheral sharing but also provides support for touch panel control and file transfer.
Chapter 1.
CE610 User Manual Requirements Consoles A DVI-D monitor capable of the highest resolution you will be using on any monitor in the installation.
Chapter 1. Introduction Operating Systems Supported operating systems are shown in the table, below: OS Windows Linux Version 2000 and higher RedHat 9.0 and higher SuSE 10 / 11.1 and higher Debian 3.1 / 4.0 Ubuntu 7.04 / 7.10 UNIX FreeBSD 5.5 / 6.1 / 6.2 Novell Netware 6.0 and higher Mac OS 10.1 and higher Note: The CE610 does not support OS that do not support USB.
CE610 User Manual Components CE610L (Local Unit) Front and Rear View Front View 1 Rear View 2 No. 5 3 Component 4 5 6 Description 1 LEDs The CE610L has four LEDs to indicate operating status – Power, Link, USB, and Video. 2 Firmware Upgrade Port The Firmware Upgrade Port is reserved for technical support. If you would like to upgrade the unit’s firmware yourself, please contact your ATEN dealer. 3 Unit to Unit Port The Cat 5e cable that connects the Local and Remote Units plugs in here.
Chapter 1. Introduction CE610R (Remote Unit) Front and Rear View Front View 1 Rear View 2 No. 3 4 Component 5 6 Description 1 LEDs The CE610R has four LEDs to indicate operating status – Power, Link, USB, and Video. 2 Firmware Upgrade Port The Firmware Upgrade Port is reserved for technical support. If you would like to upgrade the unit’s firmware yourself, please contact your ATEN dealer. 3 Unit to Unit Port The Cat 5e cable that connects the Local and Remote Units plugs in here.
Chapter 2 Hardware Setup 1. Important safety information regarding the placement of this device is provided on page 14. Please review it before proceeding. 2. Make sure that the power to all devices connected to the installation are turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. Rack Mounting For convenience and flexibility, the CE610 can be mounted on system racks. To rack mount a unit do the following: 1.
Chapter 2. Hardware Setup 2. Screw the bracket into any convenient location on the rack. Note: These screws are not provided. We recommend that you use M5 x 12 Phillips Type I cross, recessed type screws.
CE610 User Manual Installation Grounding To prevent damage to your installation it is important that all devices are properly grounded. 1. Use a grounding wire to ground both units by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object. 2. Make sure that the computer that the Local Unit connects to and the monitor that the Remote Unit connects to are properly grounded.
Chapter 2. Hardware Setup 3. For increased grounding protection, use STP (shielded twisted pair) cable to connect the Local and Remote Units. There are two methods that can be used: a) In addition to the eight paired wires, STP cable also contains a grounding wire. Solder this wire to the RJ-45 connector as shown in the diagram below: b) The second method is to use the STP cable shielding for grounding.
CE610 User Manual Setting Up Setting up the CE610 DVI KVM Extender system is simply a matter of plugging in the cables. Make sure that all the equipment to be connected up is powered off. Refer to the installation diagram on the following page and do the following: 1. Connect the USB cable supplied with the package to the USB Type B on the Local Unit (CE610L). Plug the other end of the cable into a USB Type A port on the local computer. 2.
Chapter 2.
Chapter 3 Operation LED Display The CE610 Local and Remote Units have front panel LEDs to indicate their operating status, as shown in the tables, following: CE610L (Local Unit) and CE610R (Remote Unit) LED Indication Power (Green) Lights steadily to indicate that the system is receiving power. Link (Green) Lights steadily to indicate that the connection to the Local and Remote units is ok. OFF when there is a problem with the connection.
Appendix Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation.
CE610 User Manual If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or un-interruptible power supply (UPS).
Appendix Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack. Always load the rack from the bottom up, and load the heaviest item in the rack first. Make sure that the rack is level and stable before extending a device from the rack.
CE610 User Manual Technical Support International For online technical support – including troubleshooting, documentation, and software updates: http://eservice.aten.com For telephone support, Telephone Support, page iii North America Email Support Online Technical Support support@aten-usa.com Troubleshooting Documentation Software Updates Telephone Support http://www.aten-usa.
Appendix Specifications Connectors Function CE610L CE610R DVI In 1 x DVI-D Female (White) N/A N/A 1 x DVI-D Female (White) 1 x USB Type B Female (White) 3 x USB Type A Female (White) DVI Out USB Power F/W Upgrade Unit to Unit LEDs Emulation 1 x RJ-45 Female (Black) Power 1 (Green) 1 (Green) Link 1 (Green) 1 (Green) USB 1 (Green) 1 (Green) Video 1 (Green) Keyboard / Mouse Video DC 5V 15 W Operating Temp.
CE610 User Manual Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.