User Manual CS-1732A CS-1734A 2005-12-21
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Subpart J of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CS-1732A / CS-1734A User Manual Packing List The complete Master View CS-1732A / CS-1734A package consists of: w 1 CS-1732A or CS-1734A KVM Switch w 2 CS Custom KVM Cables (CS-1732A) w 4 CS Custom KVM Cables (CS-1734A) w 1 Firmware Upgrade Cable w 1 User Manual w 1 Quick Start Guide Check to make sure that all the components are present and that nothing was damaged in shipping. If you encounter a problem, contact your dealer.
CS-1732A / CS-1734A User Manual iv 2005-12-21
CS-1732A / CS-1734A User Manual Contents 1. Features . . . . . . . . . Hardware Requirements . Console. . . . . . . Computer . . . . . . Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . 2 . . . . . . . . 3 . . . . . . . . 3 . . . . . . . . 3 . . . . . . . . 3 2. Hardware Setup CS-1732A / CS-1734A Front View . . . . . . . . . . . . . . . . .
CS-1732A / CS-1734A User Manual 4. The Firmware Upgrade Utility Before You Begin . . . . . . . Starting the Upgrade . . . . . . Upgrade Succeeded . . . . Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 24 27 27 Appendix Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1. Introduction Overview The Master View CS-1732A and CS-1734A represent a revolutionary new direction in KVM (Keyboard, Video, Mouse) Switches. The CS-1732A and CS-1734A are dual function two and four Port KVM Switches combined with 2 Port USB Hubs. As KVM switches, they allow users to access two and four computers from a single USB keyboard, USB mouse, and monitor console.
CS-1732A / CS-1734A User Manual Features w Dual function KVM-USB switch w One console controls 2 (CS-1732A ) or 4 (CS-1734A ) computers and two additional USB devices w Dual interface support - PS/2 or USB keyboard and mouse data transport* w Independent (asynchronous) switching of KVM and peripheral USB ports w Fully compliant with the USB 1.1 specification - supports transfer rates of 1.
Introduction Hardware Requirements Console w A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation. w A USB style mouse w A USB style keyboard Computer The following equipment must be installed on each computer: w A VGA, SVGA or Multisync card. w Type A USB port, or PS/2 keyboard and mouse ports. Cables Only CS Custom cable sets specifically designed to work with this switch may be used to link to the computers.
CS-1732A / CS-1734A User Manual Notes: 4 2005-12-21
Chapter 2.
CS-1732A / CS-1734A User Manual 1. Port Selection Switches w Press a switch for longer than two seconds to bring the KVM, USB hub, and audio focus to the computer attached to its corresponding port. w Press a switch for less than two seconds to bring only the KVM focus to the computer attached to its corresponding port. w Press switches 1 and 2 simultaneously for 2 seconds to start Auto Scan Mode. See p. 15 for details.
Hardware Setup CS-1732A / CS-1734A Rear View 1 4 1 4 2 2 5 3 6 6 3 5 6 6 7 2005-12-21
CS-1732A / CS-1734A User Manual 1. Console Audio Jacks The cables from your microphone and speakers plug in here. Each jack is marked with an appropriate icon to indicate itself. 2. USB Hub Section USB peripherals (printers, scanners, etc.) can plug into any available port. 3. Firmware Upgrade Section w Firmware Upgrade Switch During normal operation this switch should be in the NORMAL position.
Hardware Setup Before you Begin 1. Make sure that power to all the devices you will be connecting up have been turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. Otherwise, the switch will receive power from the computer. 2. To prevent damage to your installation make sure that all devices on the installation are properly grounded.
CS-1732A / CS-1734A User Manual 6. If you choose to use external power, plug the power adapter cable into the switch’s Power Jack, then plug the power adapter into an AC power source. Note: The power adapter should be DC5V 2.6A with the inside positive and the outside negative: 7. Turn on the power to the computers.
Hardware Setup USB Cable Connection: 5 PS/2 Cable Connection: 5 11 2005-12-21
CS-1732A / CS-1734A User Manual Hot Plugging The Master View CS-1732A / CS-1734A supports USB hot plugging - components can be removed and added back into the installation by unplugging their cables from the CPU ports without the need to shut the unit down. Powering Off and Restarting If it becomes necessary to Power Off the Master View unit, before starting it back up you must do the following: 1. Shut down all the computers that are attached to the switch.
Chapter 3. Hotkey Operation The CS-1732A / CS-1734A provides an extensive, easy-to-use, hotkey function that makes it convenient to control and configure your KVM installation from the keyboard. Hotkeys provide asynchronous (independent) switching of the KVM, USB hub and audio focus. If you wish, you can give one computer the KVM console focus, another the USB hub focus, while a third has the audio focus. Port Switching All port switches begin with tapping the Scroll Lock key twice.
CS-1732A / CS-1734A User Manual Going Directly to a Port Hotkey [Scroll Lock] [Scroll Lock] [n] [Enter] Action Brings the KVM, USB hub, and audio focus to the computer attached to the port corresponding to the specified Port ID. Note that the KVM, USB hub, and audio focus all go to this port even if they were on different ports to begin with. [Scroll Lock] [Scroll Lock] [n] [K] [Enter] Brings only the KVM focus to the computer attached to the specified port.
Hotkey Operation Auto Scanning The CS-1732A / CS-1734A‘s Auto Scan feature automatically cycles the KVM focus through the computer ports at regular intervals. This allows you to monitor the computer activity without having to take the trouble of switching from port to port manually. See the table below for details. Hotkey Action [Scroll Lock] [Scroll Lock] [A] [Enter] Starts Auto Scan. The KVM focus cycles from port to port at 5 second intervals.
CS-1732A / CS-1734A User Manual Hotkey Setting Mode Hotkey Setting Mode is used to set up your CS-1732A / CS-1734A switch configuration. All operations begin with invoking Hotkey Setting Mode (HSM). Invoking HSM To invoke HSM do the following: 1. Press and hold down the Num Lock key 2. Press and release the minus key 3. Release the Num Lock key Note: 1. There is an alternate key combination to invoke HSM. See below for details. 2.
Hotkey Operation Alternate Port Switching Keys The port switching activation keys can be changed from tapping the Scroll Lock key twice ([Scroll Lock] [Scroll Lock]) to tapping the Ctrl key twice. To change the port switching activation keys, do the following: 1. Invoke HSM (see p. 16) 2. Press and release the T key Note: This procedure is a toggle between the two methods. To revert back to the original [Scroll Lock] [Scroll Lock] method, invoke HSM, then press and release the T key again.
CS-1732A / CS-1734A User Manual List Hotkey Settings To see a listing of the current hotkey settings, do the following: 1. Invoke HSM (see p. 16). 2. Press and release the F4 function key. 3. Open a text editor or word processor and use its Paste function to display the settings. USB Reset If the USB loses focus and needs to be reset, do the following: 1. Invoke HSM (see p. 16). 2. Press and release the F5 function key. Hotkey Beeper Control The Beeper can be hotkey toggled On and Off.
Hotkey Operation Restore Default Settings To reset the CS-1732A / CS-1734A to its default hotkey settings, do the following: 1. Invoke HSM (see p. 16). 2. Press [R] [Enter]. All hotkey settings return to the factory default settings. HSM Summary Table After invoking HSM (see p. 16), key in one of the following keys to perform the corresponding function: Key Function H Toggles between the default and alternate HSM invocation keys. T Toggles between the default and alternate Port Switching keys.
CS-1732A / CS-1734A User Manual Keyboard Emulation Sun Keyboard The PC compatible (101/104 key) keyboard can emulate the functions of the Sun keyboard when the Control key [Ctrl] is used in conjunction with other keys. The corresponding functions are shown in the table below. Note: When using [Ctrl] combinatons, press and release the Ctrl key, then press and release the activation key.
Hotkey Operation Mac Keyboard The PC compatible (101/104 key) keyboard can emulate the functions of the Mac keyboard. The emulation mappings are listed in the table below. Note: When using key combinatons, press and release the first key, then press and release the second one.
CS-1732A / CS-1734A User Manual Notes: 22 2005-12-21
Chapter 4. The Firmware Upgrade Utility The Windows-based Firmware Upgrade Utility (FWUpgrade.exe) provides a smooth, automated process for upgrading the KVM switch’s firmware. The Utility comes as part of a Firmware Upgrade Package that is specific for each device. New firmware upgrade packages are posted on our web site as new firmware revisions become available. Check the web site regularly to find the latest packages and information relating to them: http://www.aten.com.tw Before You Begin 1.
CS-1732A / CS-1734A User Manual 6. Power the switch back on by plugging in one of the KVM cables. The switch’s front panel LEDs flash to indicate that it is in Firmware Upgrade Mode. Starting the Upgrade To upgrade your firmware: 1. Run the downloaded Firmware Upgrade Package file - either by double clicking the file icon, or by opening a command line and entering the full path to it. The Firmware Upgrade Utility Welcome screen appears: Note: The screenshots in this section are for example purposes.
The Firmware Upgrade Utility 1. Click Next to continue. The Firmware Upgrade Utility main screen appears: The Utility inspects your installation. All the devices capable of being upgraded by the package are listed in the Device List panel. 2. As you select a device in the list, its description appears in the Device Description panel.
CS-1732A / CS-1734A User Manual 3. After you have made your device selection(s), Click Next to perform the upgrade. If you enabled Check Firmware Version, the Utility compares the device’s firmware level with that of the upgrade files. If it finds that the device’s version is higher than the upgrade version, it brings up a dialog box informing you of the situation and gives you the option to Continue or Cancel.
The Firmware Upgrade Utility Upgrade Succeeded After the upgrade has completed, a screen appears to inform you that the procedure was successful. To complete the upgrade: 1. Click Finish to close the Firmware Upgrade Utility. 2. Power off the switch by unplugging the KVM cable that you connected in step 6 of Before You Begin (see p. 23), from the back of the switch. 3. Remove the Firmware Upgrade Cable. 4. Slide the Firmware Upgrade Switch to the Normal position. 5. Connect all the KVM cables. 6.
CS-1732A / CS-1734A User Manual Notes: 28 2005-12-21
Appendix Specifications Function CS-1732A CS-1734A Computer Connections 2 CPU Port Selection Front Panel Switches; Hotkey USB Port Selection Hotkey LEDs On Line 2 (Orange) 4 (Orange) USB Link 2 (Green) 4 (Green) Keyboard 1 x USB Type A Mouse 1 x USB Type A Video 1 x HDB -15 female Audio 1 x Stereo port 1 x Microphone port KVM data 2 x SPDB - 15 female 4 x SPDB - 15 female Audio 2 x Stereo ports 2 x Microphone ports 4 x Stereo ports 4 x Microphone ports Console Connectors CPU
CS-1732A / CS-1734A User Manual Troubleshooting Symptom Possible Cause Action Erratic behavior. Unit not receiving enough power. Use a DC 5V power adapter if you are not already using one. If you are already using a power adapter, check that it matches the system specifications (DC 5V), and that it is plugged in and functioning properly. Keyboard and/or Mouse not responding. Keyboard and/or mouse need to be reset. Press and hold port selection switches 1 and 2 for two seconds. (CS-1734A only.
The Firmware Upgrade Utility Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK OR ITS DOCUMENTATION.
