Power Over the NET™ PN7212 / PN7320 Power Distribution Unit User Manual www.aten.
PN7212 / PN7320 User Manual FCC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PN7212 / PN7320 User Manual User Information Online Registration Be sure to register your product at our online support center: International http://eservice.aten.
PN7212 / PN7320 User Manual PN Device Safety Notice Set the maximum permissible breaker protection in the building circuitry to the current rating specified on the rating plate. Observe all national regulations and safety codes as well as deviations for breakers. Only connect the PN Device to a grounded power outlet or a grounded system! Make sure that the total current input of the connected systems does not exceed the current rating specified on the rating plate of the PN Device.
PN7212 / PN7320 User Manual Package Contents The PN7212 / PN7320 package consists of: 1 PN7212 or PN7320 Power Distribution Unit 4 Serial Adapters: 1 SA0142 (RJ45F to DB9M) 1 SA0149 (RJ45F to DB9F) 1 SA0150 (RJ45F to DB9M) 1 SA0151 (RJ45F to DB9F) 2 Mounting Kits 1 User Instructions* 1 Software CD Check to make sure that all of the components are present and in good order. If anything is missing, or was damaged in shipping, contact your dealer.
PN7212 / PN7320 User Manual Contents FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Telephone Support . . . . . . . . . . . . .
PN7212 / PN7320 User Manual Chapter 5. Outlet Access Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 The Outlet Selection Sidebar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Manual Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Station Level . . . . . . . . . . . . . . .
PN7212 / PN7320 User Manual IPv4 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 IPv6 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ANMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Event Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Authentication & Authorization . . . . . . . . . . . . . . . . . .
PN7212 / PN7320 User Manual Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 The Log Server Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PN7212 / PN7320 User Manual Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Importing the Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Administrator Login Failure. . . . . . . . . . . . . . . . . . . . .
PN7212 / PN7320 User Manual About This Manual This User Manual is provided to help you get the most from your PN7212 / PN7320 system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below. Chapters 1, 4, and 5 are for all users. The remaining chapters are for administrators and users with administrator privileges. Chapter 1, Introduction, introduces you to the PN7212 / PN7320 system.
PN7212 / PN7320 User Manual Chapter 11, Out of Band Operation, explains alternative methods to access the PN7212 / PN7320 in case the LAN that it resides on goes down, or it cannot be accessed with the usual browser based method for some reason. Chapter 12, Remote Terminal Operation, describes how the PN7212 / PN7320 can be accessed via remote terminal sessions such as Telnet, SSH, and PuTTY. An Appendix, provides specifications and other technical information regarding the PN7212 / PN7320.
PN7212 / PN7320 User Manual Product Information For information about all ALTUSEN products and how they can help you connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN Authorized Reseller. Visit ALTUSEN on the Web for a list of locations and telephone numbers International http://www.aten.com North America http://www.aten-usa.
PN7212 / PN7320 User Manual This Page Intentionally Left Blank xiv
Chapter 1 Introduction Overview The PN7212 and PN7320 are power distribution units (PDUs) that contain 12 and 20 AC outlets, respectively, and are available in IEC or NEMA socket configurations. They provide secure, centralized, intelligent, power management (power on, off, cycle) of remote data center equipment (servers, KVM switches, network devices, serial data devices, etc.), as well as the ability to monitor the center's health environment.
PN7212 / PN7320 User Manual Features Power Distribution Maximum Amps/Outlet: NEMA: 20A / 12 outlets (PN7212); 30A / 20 outlets (PN7320) IEC: 16A / 12 outlets (PN7212); 32A / 20 outlets (PN7320) Space saving 0U rack mount design IEC or NEMA outlet models Daisy chain up to 15 additional stations for up to 192 (PN7212) or 320 (PN7320) outlets A 2 x 7 segment front panel LED to indicate the currently selected Station or Outlet.
Chapter 1. Introduction Operation Local and Remote power outlet control (On, Off, Power Cycle) by individual outlets and outlet groups Outlet group support at the PDU and Daisy-chain levels – the same action can be performed on a specified group of outlets at the same time Supports redundant power management via daisy chaining and outlet groups On/Off scheduling for individual outlets and outlet groups.
PN7212 / PN7320 User Manual Management Power status measurement at both the PDU, Bank, and Outlet levels LED indicators for current, voltage and active power at the PDU level Real-time current, voltage, active power, and power dissipation displayed in a browsed-based UI for monitoring at the PDU and daisy-chained PDU levels Environment monitoring – supports external temperature and humidity sensors for rack temperature and humidity monitoring Current, voltage, active power, and power dissipation
Chapter 1. Introduction Security Three-level password security IP/MAC filtering Strong security features include strong password protection and advanced encryption technologies – 128 bit SSL Remote authentication support: RADIUS, TACACS+, LDAP, LDAPS and Active Directory Requirements Browsers accessing the PN7212 / PN7320 must support SSL 128 bit encryption. For cold booting of attached computers, the computer's BIOS must support Wake on LAN or System after AC Back.
PN7212 / PN7320 User Manual Components Front View 1 3 2 3 1 4 5 6 PN7320 - NEMA 6 PN7320 - IEC
Chapter 1. Introduction No. Item Description 1 Power Sockets NEMA 5-15R – or – IEC320 C13 2 Port and LED Panel Details of this section are provided below and on the following page. 3 Power Sockets NEMA 5-20R – or – IEC320 C19 4 Circuit Breakers (PN7320 Only) As a safety measure, if there is an overcurrent situation regarding the device’s power, the circuit breakers will trip. Press the button to recover normal operation. Note: Circuit breakers are not provided on the PN7212.
PN7212 / PN7320 User Manual 3 4 5 10 11 No. 1 Item Station / Outlet Selection 6 7 8 SENSOR 2 2 STATION 1 SENSOR 1 Port and Led Panel 9 Description The Station / Outlet number appears in the display window. The two small LEDs indicate whether it is Station number or Outlet number that is displayed. The default is for the Station number to be displayed In a single stage installation, if Station is the selected mode, pressing the Left or Right button changes to Outlet mode.
Chapter 1. Introduction No. 2 Item Readout Section Description The readouts for Current, Voltage, Active Power, Sensor 1, and Sensor 2 appear in the display window. The LEDs above the items indicate which one the readout relates to. Press the button above the display window to cycle the selection among the items. The Sensor 1 and Sensor 2 LEDs correspond to the sensors plugged into the Sensor 1 and Sensor 2 ports.
PN7212 / PN7320 User Manual No. Item 6 RS-232/RS-485 Switch Description Selects which protocol the PON In / Console port uses. For PON In use, select RS-232 (for PN0108) or RS-485 For Console use, select RS-232 For KVM switches, select either RS-232 (can be used for shorter distances), or RS-485 (for longer distances). When daisy chaining PN7212 / PN7320 devices, set the switch to RS-232 on all child devices. 7 Sensor 1 A temperature or humidity sensor can plug in here.
Chapter 2 Hardware Setup Before You Begin 1. Important safety information regarding the placement of this device is provided on page 129. Please review it before proceeding. 2. The PN7212 requires a dedicated circuit. See PN Device Safety Notice, page iv, for important details. 3. Make sure that power to all the devices you will be connecting up have been turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. 1.
PN7212 / PN7320 User Manual The PN7212 / PN7320 comes supplied with top and bottom screws already inserted, as shown below: If you want to mount to brackets at the top and bottom ends of the device, you must first remove the screws from each end of the unit before attaching the mounting brackets: 12
Chapter 2. Hardware Setup Single Stage Installation In a Single Stage installation, there are no additional PN7212 / PN7320 Stations daisy chained down from the first unit. To set up a single stage installation, refer to the installation diagram on the next page (the numbers in the diagram correspond to the numbered steps), and do the following: 1.
PN7212 / PN7320 User Manual 9. Connect the PN7212 / PN7320's power cord to an AC power source. Note: 1. We strongly advise that you do not plug the PN7212 / PN7320 into a multi socket extension cord, since it may not receive enough amperage to operate correctly. 2. Circuit breakers are not provided on the PN7212. Therefore, we strongly recommend that you do no plug the unit directly into any unprotected power source (such as a wall outlet). See PN Device Safety Notice, page iv.
Chapter 2. Hardware Setup Daisy Chaining To manage even more outlets from the same single session as a standalone PN7212 / PN7320, additional Power Over the NET™ devices can be daisy chained, as described in the following three configurations. Note: The maximum distance between any two Power Over the NET™ devices must not exceed 15 m; the total distance from the first station to the last must not exceed 100 m.
PN7212 / PN7320 User Manual 16
Chapter 2. Hardware Setup PN7212 / PN7320 to PN0108 To daisy chain a child PN0108 from a parent PN7212 / PN7320, do the following: 1. Use Cat 5e cable to connect the PN7212 / PN7320’s PON OUT port to the SA0150 Adapter supplied with your package. 2. Connect the SA0150 to the PN0108’s PON IN port.
PN7212 / PN7320 User Manual This Page Intentionally Left Blank 18
Chapter 3 Super Administrator Setup First Time Setup Once the PN7212 / PN7320 installation has been cabled up, the next tasks the Administrator needs to perform involve configuring the network parameters, changing the default Super Administrator login settings, and adding users. The easiest way to accomplish this is to log in over the Net with a browser (see Logging In, page 23). Note: 1.
PN7212 / PN7320 User Manual Network Configuration To set up the network, do the following: 1. Click the Device Management tab. 2. Select Network on the menu bar. A screen similar to the one below appears: 3. Fill in the fields according to the information provided under Network, page 65.
Chapter 3. Super Administrator Setup Changing the Administrator Login To change the default Super Administrator username and password, do the following: 1. Click the User Management tab. The User Management page has a list of Users and Groups in the Sidebar at the left, and a more detailed list of users – with more information about them – in the large central panel. Since this is the first time the page is being accessed, only the Super Administrator appears: 2.
PN7212 / PN7320 User Manual (Continued from previous page.) The User General page appears: 3. Change the Username and Password to something unique. 4. Re-enter the password to confirm it is correct. 5. Click Save. 6. When the dialog box informing you that the change completed successfully appears, Click OK. Moving On After setting up the network and changing the default Administrator username and password, you can proceed to other administration activities – including adding users.
Chapter 4 Browser Login Logging In The PN7212 / PN7320 can be accessed via a supported Internet browser from any platform. Note: Browsers must support SSL 128 bit encryption. To access the PN7212 / PN7320 do the following: 1. Open your browser and specify the IP address of the PN7212 / PN7320 you want to access in the browser's URL location bar. Note: 1. Get the IP address from the PN7212 / PN7320 administrator 2.
PN7212 / PN7320 User Manual The PN7212 / PN7320 Main Page After you have successfully logged in, the PN7212 / PN7320 Main Page comes up with the Outlet Access Connections page displayed: Note: 1. The screen depicts a Super Administrator’s page. Depending on a user’s type and permissions, not all of these elements appear. 2. Clicking the ALTUSEN logo (at the top-right of the page), takes you to the ATEN website.
Chapter 4. Browser Login Page Components The web page screen components are described in the table, below: No. Item Description 1 Tab Bar The tab bar contains the Power Over the NET™’s main operation categories. The items that appear in the tab bar are determined by the user’s type, and the authorization options that were selected when the user’s account was created. 2 Menu Bar The menu bar contains operational sub-categories that pertain to the item selected in the tab bar.
PN7212 / PN7320 User Manual This Page Intentionally Left Blank 26
Chapter 5 Outlet Access Overview When you log in to the PN7212 / PN7320 UI opens with its default selection of the Outlet Access tab; the Connections menu; and the Outlets submenu. The contents of the Outlets submenu are displayed in the main panel. The main panel Outlets display provides a detailed listing of each outlet a user is permitted to access, as well as a means of accessing the outlets. All the outlets that a user is permitted to access are also listed in the Sidebar at the left of the page.
PN7212 / PN7320 User Manual The Outlet Selection Sidebar All stations and their outlets – including cascaded stations and their outlets – are listed in a tree structure in the Sidebar at the left of the screen. Outlet groups are listed at the bottom of the tree: Users are only allowed to see the stations and outlets that they have access permission for. Outlets and child stations may be nested under their parent stations. Click the + in front of a station to expand the tree and see the nested outlets.
Chapter 5. Outlet Access The outlet’s icon color indicates its status as explained in the table, below: Icon Status Steady Amber Power to the outlet is On. Flashing Amber A change in the outlet's power status is pending. (See Shutdown Method, page 46) Steady Gray Power to the outlet is Off. Flashing Gray Power to the outlet is Off, but Wake On LAN has been specified as the remote power option. (See Shutdown Method, page 46.) Flashing Lightbulb Indicates an outlet status error.
PN7212 / PN7320 User Manual Group General Page With the exception of the power outlet icon, the pages are view only and provide power status and usage information. To configure the settings, select Configuration at the far right of the menu bar. See Configuration, page 40 for details. The color of the power outlet icon indicates its status (as explained in the table on page 29). The power status of the outlet can be changed by clicking the icon. Note: 1.
Chapter 5. Outlet Access Connections The Connections pages provide status and settings information for stations, outlets, and outlet groups. The pages that come up in the main panel differ depending on which item is selected in the Sidebar.
PN7212 / PN7320 User Manual General The station’s General page shows the station’s settings configuration: This page only displays information. Settings changes cannot be made here. To configure the settings, select Configuration at the far right of the menu bar. See Configuration, page 40 for details. Groups The station’s Groups page lists the names of the outlet groups that have been created with its outlets in the left column.
Chapter 5. Outlet Access Outlet Level When an outlet is selected in the Sidebar, the main panel tabs change to General, Configuration, and Schedule. Each of the tabs is described below. General The outlet’s General page provides information regarding the outlet’s name, power status, amps, watts, volts and power dissipation status: You can manually turn the outlet On and Off from this page by clicking the power outlet icon (see Manual Power Management, page 29 for details).
PN7212 / PN7320 User Manual Configuration The outlet’s Configuration page summarizes the various configuration settings that have been made for the outlet: This page only displays information. Settings changes cannot be made here. To configure the settings, select Configuration at the far right of the menu bar. See Configuration, page 40 for details.
Chapter 5. Outlet Access Server Diagnosis The outlet’s Server Diagnosis page allows you to use an ICMP ping command to check if the outlet is functioning properly. This function is detailed in the following table: Enable Put a check in the checkbox to enable this function. Ping Address Enter the IP address of the outlet to be pinged in this field. Interval This field sets how often the specified outlet is pinged, in second intervals. Enter a value between 1 and 255.
PN7212 / PN7320 User Manual Outlet Group Level When an outlet group is selected in the Sidebar, the main panel tabs change to General, and Schedule. Each of the tabs is described below. General The outlet group’s General page provides information regarding the group’s name, the outlets that belong to the group, and the power status of the outlets: You can manually turn the outlets On and Off from this page by clicking the power outlet icon (see Manual Power Management, page 29 for details).
Chapter 5. Outlet Access User Preferences The User Preferences page allows users to set up their own, individual, working environments. The PN7212 / PN7320 stores a separate configuration record for each user profile, and sets up the working configuration according to the Username that was keyed into the Login dialog box. Make your settings changes according to the information given in the following table: Setting Language Function Selects the language that the interface displays in.
PN7212 / PN7320 User Manual Sessions The Session page shows all of the users currently logged into the PN7212 / PN7320, and provides information about each of their sessions. The information under the IP heading indicates the IP address that the user is logged in from. The information under the Client heading indicates whether the user has logged in via a browser connection (HTTPS), or from a local console.
Chapter 5. Outlet Access Outlet Level When an outlet is selected in the Sidebar, a page similar to the one below, comes up in the main panel: Users and groups are listed alphabetically in the left column. A check mark under the Access column, indicates the user or group is authorized to access and power control the selected outlet. A check mark under the Outlet Configuration column, indicates the user or group is authorized to configure the selected outlet’s settings (see Configuration, page 40).
PN7212 / PN7320 User Manual Configuration The Configuration page is used to configure the operation of the PN7212 / PN7320 at both the station level and the individual power outlet level. The items available differ depending on whether a station or an outlet is selected in the Sidebar. Station Level Configuration When a station is selected in the Sidebar, a page similar to the one below, displays in the main panel.
Chapter 5. Outlet Access General When the Configuration page opens, the station’s General page is selected. This page allows you to set up a power management configuration for the device as a whole. The meanings of the field headings are given in the following table: Heading Meaning Device Name To make things more convenient on a multi-station installation, each station can be given a distinctive name. To name a station key in the name of your choice - up to 32 letters and numbers.
PN7212 / PN7320 User Manual Groups Outlet groups enable power configuration and control actions to be carried out on a selected group of outlets at the same time, rather than repeatedly performing the same action on each individual one. The Groups page lists the outlet groups that have already been configured, and shows which outlets are included in the group. Note: In the Outlet column the outlets are displayed as [Station ID-Outlet Number].
Chapter 5. Outlet Access 3. Click to put a checkmark in the checkbox of the outlets you want to add to the group, then click Save. When you return to the Group page, your new group is included in the list: Note: The group also shows up as a device in the Sidebar, and this page can be accessed by clicking on its icon in the Sidebar. To Modify an outlet group, select it in the list, then click Modify. The screen that comes up is the same one that appears when you click Add.
PN7212 / PN7320 User Manual Outlet Level Configuration The configuration settings for a PN7212 / PN7320 can be specified on an outlet by outlet basis. When an outlet is selected in the Configuration page Sidebar, the main panel displays a page with two tabs: Configuration, and Schedule, as described in the sections that follow. Configuration The Configuration tab page, similar to the one below, is the default that appears in the main panel.
Chapter 5. Outlet Access This page lets you set up the power management configuration for the selected outlet. The meanings of the field headings are given in the following table: Heading Meaning Outlet Name Each outlet can be given a distinctive name. The maximum number of characters is 15. Alarm A checkmark in the check box disables an alarm from being triggered when any of the threshold settings fall outside of their specified ranges.
PN7212 / PN7320 User Manual Heading Shutdown Method Meaning There are three choices for the Shutdown method. Drop down the list to select a choice. The meaning of each choice is described, below: Wake on LAN: This is a Safe Shutdown and Restart option.
Chapter 5. Outlet Access Schedule Clicking the Schedule tab brings up a page that lets you set up a scheduled power On/Off configuration for the selected outlet: The meanings of the field headings are given in the table, below: Heading Meaning Routine Type Drop down the list to select whether the scheduled power configuration should take place just Once, or on a Daily, Weekly, or Monthly basis. Week Day This field only becomes active if you choose Weekly as the routine type.
PN7212 / PN7320 User Manual Heading Shutdown Time Meaning Key in the time of day you want the shutdown to take place using the HH:MM format. If you want to temporarily suspend this function without deleting the entry, click to put a check in the Disable checkbox at the right of this field. You can reinstate the function by unchecking the checkbox. Restart Time Key in the time of day you want the restart to take place using the HH:MM format.
Chapter 6 User Management Overview When you select the User Management tab the screen comes up with Accounts selected in the Menu bar, and the User List displayed in the main panel: 49
PN7212 / PN7320 User Manual The Accounts page has two menu items: Accounts, for managing individual users; and Groups, for managing user groups. Note: There is a pre-installed super administrator account. It can be used to set up the device and to begin creating users and groups. The Username for this account is administrator; the password is password. For security purposes, we strongly recommend changing these to something unique. See Modifying User Accounts, page 53 for details.
Chapter 6. User Management 3. Enter the required information in the appropriate fields. A description of each of the fields is given in the table below: Field Description Username From 1 to16 characters are allowed depending on the Account Policy settings. See Account Policy, page 89. Password From 1 to16 characters are allowed depending on the Account Policy settings. See Account Policy, page 89. Confirm Password To be sure there is no mistake in the password, you are asked to enter it again.
PN7212 / PN7320 User Manual Field Status Description Status allows you to control the user’s account and access to the installation, as follows: Disable Account lets you suspend a user’s account without actually deleting it, so that it can be easily reinstated in the future. If you don’t want to limit the time scope of the account, select Account never expires; if you want to limit the amount of time that the account remains in effect, select Account expires on, and key in the expiration date.
Chapter 6. User Management Modifying User Accounts To modify a user account, do the following: 1. In the Sidebar User tree, click the user’s name – or – In the main panel, select the user’s name, then click Modify. 2. In the User page that comes up is the same as the one for adding users (see page 50). Make your changes, then click Save. Deleting User Accounts To delete a user account do the following: 1. In the main panel, select the user’s name, then click Delete. 2. Click OK.
PN7212 / PN7320 User Manual Groups Groups allow administrators to easily and efficiently manage users and devices. Since device access rights apply to anyone who is a member of the group, administrators need only set them once for the group, instead of having to set them for each user individually. Multiple groups can be defined to allow some users access to specific devices, while restricting other users from accessing them. Note: This section refers to the Groups menu.
Chapter 6. User Management 4. Enter the required information in the appropriate fields. A description of each of the fields is given in the table below: Field Description Group Name A maximum of 16 characters is allowed.
PN7212 / PN7320 User Manual Modifying Groups To modify a group, do the following: 1. In the Sidebar Group tree, click the group’s name – or – In the main panel, select the group’s name, then click Modify. 2. The Groups page that comes up is the same as the one for adding groups (see page 54). Make your changes, then click Save. Deleting Groups To delete a group do the following: 1. In the main panel, select the group’s name, then click Delete. 2. Click OK.
Chapter 6. User Management Users and Groups There are two ways to assign users to – and remove users from – groups: from the Accounts menu; and from the Groups menu. Note: 1. Before you can assign users to groups, you must first create them. See Adding Users, page 50 for details. 2. If a user has permissions in addition to the ones assigned to the group, the user keeps those permissions in addition to the group ones.
PN7212 / PN7320 User Manual Removing Users From a Group From the Accounts Page To remove a user from a group from the Accounts page, do the following: 1. In the Sidebar Users tree, click the user’s name – or – In the main panel, select the user’s name, then click Modify. 2. In the page that comes up, select the Groups tab. A screen, similar to the one below, appears: 3. In the Selected column, select the group that you want to remove the user from. 4.
Chapter 6. User Management Assigning Users to a Group From the Groups Page To assign a user to a group from the Groups page, do the following: 1. In the Sidebar User Groups tree, click the group’s name – or – In the main panel, select the group’s name, then click Modify. 2. In the page that comes up, select the Members tab. A screen, similar to the one below, appears: 3. In the Available column, select the user that you want to be a member of the group. 4.
PN7212 / PN7320 User Manual Removing Users From a Group From the Groups Page To remove a user from a group from the Groups page, do the following: 1. In the Sidebar User Groups tree, click the group’s name – or – In the main panel, select the group’s name, then click Modify. 2. In the page that comes up, select the Members tab. A screen, similar to the one below, appears: 3. In the Selected column, select the user that you want to remove from the group. 4.
Chapter 6. User Management Device Assignment When a user logs in to the Power Over the NET™ device, the interface comes up with the Outlet Access page displayed. All the outlets that the user is permitted to access are listed in the Sidebar at the left of the page. Access permissions for those outlets can be assigned on an outlet-by-outlet basis from the Accounts menu for individual users, or the Groups menu for user groups.
PN7212 / PN7320 User Manual 3. Under the Access column, click to permit or restrict the user’s access to an outlet. A check mark ( √ ) indicates that the user has permission to access the outlet; a blank checkbox means that the user is denied permission to access the outlet. 4. Under the Configuration column, click to permit or restrict the user’s ability to change the outlet’s configuration settings.
Chapter 7 Device Management Overview The Device Management page allows super administrators, administrators, and users with device management permission to configure and control overall Power Over the NET™ device operations.
PN7212 / PN7320 User Manual The page presents information about the selected device, as described in the following table. Item Meaning Device Name This field lets you give the device a unique name. This can be convenient when you need to differentiate among several devices in multi station installations. Simply delete whatever is in the text box and key in the name of your choice. Click Save to save the new name. MAC Address This item displays the Power Over the NET™ device’s MAC address.
Chapter 7. Device Management Network The Network page is used to specify the Power Over the NET™ device’s network environment. The main section is divided into 5 panels. Select the device you want to configure in the Sidebar, then fill in the information in the panels according to the information given in the sections that follow. When you have finished making all of your configuration settings, click Save (at the bottom of the page).
PN7212 / PN7320 User Manual Settings This field specifies the time interval for the browser page to automatically refresh and display the latest power information. IP Installer The IP Installer is an external Windows-based utility for assigning IP addresses to the Power Over the NET™ device. Click one of the radio buttons to select Enable, View Only, or Disable for the IP Installer utility. See Method 1:, page 138, for IP Installer details. Note: 1.
Chapter 7. Device Management IPv4 Configuration The device’s IPv4 IP and DNS addresses (the traditional method of specifying IP addresses) can either be assigned dynamically (DHCP), or a fixed IP address can be specified. For dynamic IP address assignment, select the Obtain IP address automatically radio button. (This is the default setting.) To specify a fixed IP address, select the Set IP address manually radio button and fill in the IP address with values appropriate for your network.
PN7212 / PN7320 User Manual IPv6 Configuration The device’s IPv6 IP and DNS addresses (the new method of specifying IP addresses) can either be assigned dynamically, or a fixed IP address can be specified. For dynamic IP address assignment, select the Enable Autoconfiguration radio button. (This is the default setting.
Chapter 7. Device Management ANMS The ANMS (Advanced Network Management Settings) page is used to set up event notifications, login authentication and authorization management from external sources, and CC Management. It is organized in three tabbed pages: Event Notification; Authentication & Authorization; CC Management; and SNMP Agent. These pages are explained in the sections that follow Event Notification When you select ANMS on the menu bar, the GUI displays the Event Notification tab’s page.
PN7212 / PN7320 User Manual 4. Key in the email address (addresses) of where you want the event reports sent to in the To field. Note: If you are sending the report to more than one email address, separate the addresses with a semicolon. The total cannot exceed 256 Bytes. Log Server Important transactions that occur on the Power Over the NET™ device, such as logins and internal status messages, are automatically generated and kept by an ATEN Log Server program.
Chapter 7. Device Management SNMP Trap Receivers Up to four SNMP management stations can be specified. If you want to use SNMP trap notifications, do the following: 1. Check Enable SNMP Trap. 2. Select the SNMP protocol from the three options provided. 3. Key in the IP address(es) and the service port number(s) of the computer(s) to be notified of SNMP trap events. The valid port range is 1–65535. The default port number is 192.
PN7212 / PN7320 User Manual Syslog Server To record all the events that take place on Power Over the NET™ devicees and write them to the PN7212 / PN7320 Syslog server, do the following: 1. Check Enable. 2. Key in the IP address and the port number of the Syslog server. The valid port range is 1-65535. The default port number is 514. Finishing Up When you have finished making your settings on this page, click Save.
Chapter 7. Device Management Authentication & Authorization The Authentication & Authorization page is used to set up login authentication and authorization management from external sources. Disable Local Authentication Selecting this option will disable login authentication locally on the Power Over the NET™ device. The device can only be accessed using LDAP, LDAPS, MS Active Directory, RADIUS, TACACS+, or CC Management authentication.
PN7212 / PN7320 User Manual 4. In the Retries field, set the number of allowed retries for attempting to connect to the RADIUS server. 5. In the Shared Secret field, key in the character string that you want to use for authentication between the Power Over the NET™ device and the RADIUS Server. 6. On the RADIUS server, set the entry for each user as follows: su/xxxx Where xxxx represents the Username given to the user when the account was created on the Power Over the NET™ device.
Chapter 7. Device Management To allow authentication and authorization for the Power Over the NET™ device through an LDAP/AD server, refer to the information in the table, below: Item Action Enable Put a check in the Enable checkbox to allow LDAP authentication and authorization. Enable SSL Put a check in the Enable SSL checkbox to specify an SSL connection. Preferred/Alternate LDAP Server IP Fill in the IP address for the preferred/alternate LDAP server.
PN7212 / PN7320 User Manual TACACS+ To allow authentication and authorization for the Power Over the NET™ device through a TACACS+ server, do the following: 1. Check Enable. 2. Fill in the IP addresses and port numbers for the Preferred and Alternate TACACS+ servers. The default port number is 49. Note: Make sure that the port numbers you specify here match the port numbers used by the TACACS+ servers. 3.
Chapter 7. Device Management CC Management This page allows you to manage authentication and authorization for the Power Over the NET™ device through a CC (Control Center) server. If this is enabled, users will be able to access the device via their CC session. To allow authentication and authorization for the Power Over the NET™ device through a CC (Control Center) server, check Enable and fill in the CC Server’s IP address and the port that it listens on in the appropriate fields.
PN7212 / PN7320 User Manual SNMP Agent If you want to use SNMP to help with your installation management: 1. Check Enable. 2. Once SNMP Agent has been enabled, the SNMP Agent Service Port field becomes active. Enter the port number here. 3. Key in passwords for the Community Name fields. We recommend replacing the defaults (public, private) with an alphanumeric string of at least 8 characters. 4. When you have finished making all your entries, click Save, to save them.
Chapter 7. Device Management OOBC In case the LAN that the Power Over the NET™ device resides on goes down, or the it cannot be accessed with the usual browser based method for some other reason, the device can be accessed via Out of Band methods utilizing the its Console or Modem port. The OOBC page is used to set up the serial configuration parameters for serial terminal and modem Out of Band access to the Power Over the NET™ device, as described in the sections that follow.
PN7212 / PN7320 User Manual Note: The Console port’s serial parameters and the parameters of the device it connects to must both be the same.
Chapter 7. Device Management Modem Settings This section is used to enable support for modem dial in / dial back operations. For this function, you must establish an account with an ISP (Internet Service Provider), and then use a modem to dial to your ISP account. See Modem Session, page 119 for details Protocol Settings These parameters specify the way your ISP has its modem connection and authentication protocols set up.
PN7212 / PN7320 User Manual Dial In allows you to establish a connection to the PN7212 / PN7320 via a dial up modem connection. Dial Back is provided as an added security feature. If this option is enabled, the PN7212 / PN7320 disconnects the original dial in connection and dials back to a specified modem, as explained in the table, below: Item Action Dial Back Timeout Specifies amount of time to wait for the dial back modem to answer before hanging up.
Chapter 7. Device Management Dial Out Settings If you want the Power Over the NET™ device to be able to dial out, activate the dial out function by putting a checkmark in the Enable Dial Out checkbox. Note: Unless this function is enabled, you will only be able to dial in. None of the dial out functions (described below) will occur.
PN7212 / PN7320 User Manual Complete the Dial Out configuration as follows: 1. Under Modem Settings, specify your modem's configuration: If your modem isn't in the Modem Type listbox, specify Generic Modem for the type. Specify your modem's initialization string in the Initialization String field. Consult your modem's User Manual, if necessary. 2. Under ISP Settings, specify the telephone number, Username, and Password that you use to connect to your ISP. 3.
Chapter 7. Device Management 5. The SMTP Server settings are used to send an email notifying you of the IP address that was dynamically assigned to the device by the ISP when a dial out occurs. Key in the name or IP address of the ISP's SMTP mail server in the SMTP Server: field. If the server requires authentication, check the SMTP server requires authentication checkbox and key in your account name and password in the fields provided.
PN7212 / PN7320 User Manual Security The Security page controls access to the Power Over the NET™ device.
Chapter 7. Device Management Login String The Login String entry field is used to specify a login string (in addition to the IP address) that users must include when accessing the Power Over the NET™ device with a browser. For example: 192.168.0.126/abcdefg The following characters are allowed: 0–9 a–z A–Z ~ ! @ $ & * ( ) _ + - = [ ] ; ' , . The following characters are not allowed: ^ { } ‘ ’ < > | " % ” : / ? # \ [Space] Compound characters (É Ç ñ ... etc.) Note: 1.
PN7212 / PN7320 User Manual Adding Filters To add an IP filter, do the following: 1. Click Add. A dialog box similar to the one below appears: 2. Specify the filter address in the dialog box (for example, 192.168.0.200), then click OK. A second dialog box, similar to the one below, appears: 3. To filter a single IP address, key in the same address as the start IP. To filter a continuous range of addresses, key in the end number of the range (for example, 192.168.0.225). 4.
Chapter 7. Device Management 2. Specify the MAC address in the dialog box (for example, 001074670000), then click OK. Repeat these steps for any additional MAC addresses you want to filter. IP Filter / MAC Filter Conflict If there is a conflict between an IP filter and a MAC filter – for example, where a computer’s IP address is allowed by the IP filter but it’s MAC address is excluded by the MAC filter – then that computer’s access is blocked.
PN7212 / PN7320 User Manual Private Certificate When logging in over a secure (SSL) connection, a signed certificate is used to verify that the user is logging in to the intended site. For enhanced security, the Private Certificate section allows you to use your own private encryption key and signed certificate, rather than the default ATEN certificate.
Chapter 7. Device Management Customization The Customization page is used to set Login Failure and Working Mode parameters. Login Failures Allowed sets the number of consecutive failed login attempts that are permitted from a remote user. Timeout sets the amount of time a remote user must wait before attempting to login again after exceeding the number of allowed failures. Working Mode If ICMP is enabled, the Power Over the NET™ device can be pinged.
PN7212 / PN7320 User Manual Date/Time The Date/Time dialog page sets the Power Over the NET™ device time parameters: Set the parameters according to the information described below. Time Zone To establish the time zone that the Power Over the NET™ device is located in, drop down the Time Zone list and choose the city that most closely corresponds to where it is at. If your country or region employs Daylight Saving Time (Summer Time), check the corresponding checkbox.
Chapter 7. Device Management Manual Input Use this section to specify the Power Over the NET™ device’s date and time manually. Click the calendar icon and click the calendar entry for the date. Key the time into the Time field, using the HH:MM:SS (hours, minutes, seconds) format. Note: This section is only enabled when auto adjustment (in the Network Time section) is disabled (the checkbox is unchecked).
PN7212 / PN7320 User Manual This Page Intentionally Left Blank 94
Chapter 8 Log Overview The PN7212 / PN7320 keeps an extensive record of all the transactions that take place on its installation. The Log page provides a powerful array of filters and functions that allow you to view and export the log file data, as well as be informed by email of specified events as they occur.
PN7212 / PN7320 User Manual The Log Event List Clicking on a device in the Sidebar displays its log events in the main panel’s log event list. Clicking the Refresh button brings the log list up to date with the latest events. The entry box to the right of the Refresh button lets you set the number of events to display per page. Simply key in the number of your choice. The top right of the main panel shows the total number of pages in the log file, and what page you are currently viewing.
Chapter 8. Log Search Search allows you to search for events according to selected criteria, such as: specific words, users, date, time, severity, and category. You can also search on any combination of criteria to refine the search even further. When you click the Search icon, a Search panel, similar to the one below, appears: To search on a keyword, key it into the Keyword text box.
PN7212 / PN7320 User Manual Save Save allows you to save the contents of the event log list (or the results of a Search), to a file. When you click the Save icon, similar to the one below appears: To save specified logged events to a file, do the following: 1. Click one of the radio buttons to specify the file format you want to save the file in (csv files can be read by a spreadsheet program). 2. Click Save. After a moment, a dialog box similar to the one below comes up: 3.
Chapter 8. Log Notification Settings The Notification Settings page is used to specify which of the PN7212 / PN7320’s components will receive notification of a log event. When you click the Notification Settings menu item, a page similar to the one below appears: The event categories are listed in the left column. When you first open the page, only the main category items appear. (Main category item rows have a gray background.) Sub-category items are nested under the main category headings.
PN7212 / PN7320 User Manual This Page Intentionally Left Blank 100
Chapter 9 Maintenance and Download Overview The Maintenance function is used to upgrade the PN7212 / PN7320’s firmware, and to backup and restore the device’s configuration settings. Download is used to download a stand-alone Java Client AP program to access the PN7212 / PN7320.
PN7212 / PN7320 User Manual The Main Panel A description of the items shown in this panel are given in the table, below: Item Description Check Main Firmware Version If you enable Check Main Firmware Version, the PN7212 / PN7320’s current firmware level is compared with that of the upgrade file. If the current version is equal to or higher than the upgrade version, a popup message appears, to inform you of the situation and stops the upgrade procedure. Name Lists all of the PN7212 / PN7320 devices.
Chapter 9. Maintenance and Download Firmware Upgrade Recovery Should the PN7212 / PN7320’s firmware upgrade procedure fail, and the device becomes unusable, the following firmware upgrade recovery procedure will resolve the problem: 1. Power off the device. 2. Press and hold the Reset Switch in (see page 9). 3. While holding the Reset Switch in, power the switch back on. This causes the switch to use the original factory installed main firmware version.
PN7212 / PN7320 User Manual Backup To backup the device’s settings do the following: 1. In the Password field, key in a password for the file. Note: Entering a password is optional. If you do enter a password, make a note of it, since you will need it to be able to restore the file. 2. Click Save. 3. When the browser asks what you want to do with the file, select Save to disk; then save it in a convenient location. Restore To restore a previous backup, do the following: 1.
Chapter 9. Maintenance and Download Download Download is used to download a stand-alone Java Client AP version of the PN7212 / PN7320 software. When you click the Download tab, the browser brings up a dialog box asking what you want to do with the program file: The Java Client AP can be run via a console terminal connection from your computer’s COM port to the PN7212 / PN7320’s Console Port.
PN7212 / PN7320 User Manual This Page Intentionally Left Blank 106
Chapter 10 The Log Server The Windows-based Log Server is an administrative utility that records all the events that take place on selected Power Over the NET™ devices and writes them to a searchable database. This chapter describes how to install and configure the Log Server. Installation The Log Server AP Installer is provided on the CD that came with your Power Over the NET™ device. To install the Log Server, do the following: 1.
PN7212 / PN7320 User Manual Starting Up To start the Log Server, either double click the program icon, or key in the full path to the program on the command line. The first time your run it, a screen similar to the one below appears: Note: 1. The MAC address of the Log Server computer must be specified under the ANMS settings – see Log Server, page 70 for details. 2. The Log Server requires the Microsoft Jet OLEDB 4.0 driver. See The Log Server program does not run., page 148 if the program doesn’t start.
Chapter 10. The Log Server The Menu Bar The Menu bar consists of four items: Configure Events Options Help These are discussed in the sections that follow. Note: If the Menu Bar appears to be disabled, click in the List window to enable it. Configure The Configure menu contains three items: Add; Edit; and Delete. They are used to add new units to the List; edit the information for units already on the list; or delete units from the list. To add a unit to the list, click Add.
PN7212 / PN7320 User Manual A description of the fields is given in the table, below: Field Explanation Address This can either be the IP address of the unit or its DNS name (if the network administrator has assigned it a DNS name). Port The port number that was assigned to the Log Server (see Log Server, page 70). Description This field is provided so that you can put in a descriptive reference for the unit to help identify it.
Chapter 10. The Log Server A description of the items is given in the table, below: Item Description New search This is one of three radio buttons that define the scope of the search. If it is selected, the search is performed on all the events in the database for the selected unit. Search last results This is a secondary search performed on the events that resulted from the previous search.
PN7212 / PN7320 User Manual Options Network Retry allows you to set the number of seconds that the Log Server should wait before attempting to connect if its previous attempt to connect failed. When you click this item, a dialog box, similar to the one below, appears: Key in the number of seconds, then click OK to finish. Help From the Help menu, click Contents to access the online Windows Help file. The help file contains instructions about how to setup, operation and troubleshoot the Log Server.
Chapter 10. The Log Server The Log Server Main Screen Overview The Log Server Main Screen is divided into two main panels. The upper (List) panel lists all of the units that have been selected for the Log Server to track (see Configure, page 109). The lower (Event) panel displays the tick information for the currently selected unit. (If there are more than one unit, the selected unit is the one that is highlighted). To select a unit in the list, simply click on it.
PN7212 / PN7320 User Manual The List Panel The List panel contains six fields: Field Recording Explanation Determines whether the Log Server records the ticks for this unit, or not. If the Recording checkbox is checked, the field displays Recording, and the ticks are recorded. If the Recording checkbox is not checked, the field displays Paused, and the ticks are not recorded.
Chapter 11 Out of Band Operation Overview In case the LAN that the PN7212 / PN7320 resides on goes down, or the PN7212 / PN7320 cannot be accessed with the usual browser based method for some other reason, the PN7212 / PN7320 can be accessed via Out of Band methods utilizing the PN7212 / PN7320's Console and Modem ports in the following ways: For a console terminal session, connect the PN7212 / PN7320’s Console port (see PON In / Console Port, page 10), to the COM port of a local computer.
PN7212 / PN7320 User Manual 2. On your local computer, run the HyperTerminal program: 3. When a dialog box, similar to the one below appears, key in a name to describe the connection in the Name field, select an icon to represent the connection; then click OK. Note: In the examples we used Com1Test for the Name, and COM1 for the computer’s COM port. If you use a different COM port, change the settings accordingly.
Chapter 11. Out of Band Operation 4. For the Connect using: field, select Direct to COM1 (assuming you are using COM1 on your computer), then click OK. A Port Setting dialog box similar to the one below comes up: 5. Fill in the settings so that the match the ones you specified for the PN7212 / PN7320's console port settings on the OOBC page (see Console Port Settings, page 79), then click OK. 6. When the HyperTerminal screen appears, open its File menu and select: Properties → Settings.
PN7212 / PN7320 User Manual 7. Change your settings (if necessary), so that they match the settings shown in the diagram, then click ASCII Setup... 8. In the ASCII Setup dialog box that comes up, change the settings (if necessary), so that they match the settings shown in the diagram below, then click OK. 9. Close the HyperTerminal window. When Windows asks if you want to disconnect, click Yes. When Windows asks if you want to save the session, click Yes. This completes the HyperTerminal setup.
Chapter 11. Out of Band Operation Modem Session The PN7212 / PN7320’s modem port makes it possible to access the PN7212 / PN7320 from a remote location with a dial in/dial back session. Connection Setup 1. Set up your hardware configuration to match the diagram, below: Cat 5e Cable Serial Cable Phone Line SA0142 (DCE) Remote Operator Modem Modem Note: The PN7212 / PN7320’s modem must be set to Auto Answer incoming calls. 2.
PN7212 / PN7320 User Manual The following dialog box appears: Note: In the examples that follow we use COM1. If you use a different COM port, change the settings accordingly. 3. Key a name of your choice in the top text box; select Standard 28800 bps Modem for the device; then click Configure.
Chapter 11. Out of Band Operation Change your settings (if necessary), so that they match the settings shown in the figure above (assuming you are using COM1 - if not choose a port setting that matches the COM port you are using). Note: If you change the baud rate (speed), you must turn your modem Off and On for the change to take effect. 4. Click the Connection tab to see the connection setup page: 5.
PN7212 / PN7320 User Manual 6. If there is a check mark in the Use flow control checkbox, uncheck it, then click OK. 7. Click OK; then click Next. The following dialog box appears: 8. Key in the telephone number of the PN7212 / PN7320’s modem in the Telephone number field, then click Next. 9. Click Finish. A new icon that you can use to connect to the PN7212 / PN7320 is created in the Dial-up Network folder.
Chapter 11. Out of Band Operation Finishing Up 1. Right click on the icon you just created, and select Properties. In the dialog box that appears, select the Server Types tab: 2. Match the checkboxes in the dialog box to the ones in the diagram, then click TCP/IP Settings.
PN7212 / PN7320 User Manual 3. Change the dialog box settings so that your radio buttons and check boxes match the ones in the diagram. 4. Click OK to leave the dialog box; then click OK again. This completes the modem connection setup. Logging In 1. On the Device Management OOBC page, make sure that the Enable Dial In radio button is selected. (See Dial In / Dial Back Settings, page 81.) 2. Double click the icon you created in the Dial-up Network folder (see page 122). 3.
Chapter 12 Remote Terminal Operation Overview The PN7212 / PN7320 can be accessed via a remote terminal session using several methods, including Telnet, SSH, or PuTTY, as described in the sections that follow. Telnet Logging In To log in to the PN7212 / PN7320 by means of a Telnet session, do the following: 1. On your computer, open a terminal (command line) session. 2. At the prompt, key in the PN7212 / PN7320's IP Address in the following way: telnet [IP Address] 3. Press Enter.
PN7212 / PN7320 User Manual Once a Telnet connection to the device is established, the PN7212 / PN7320’s text-based Configuration Menu comes up: The text-based Configuration Menu provides text-based equivalents for the functions found under the web-based tabs and menus. You can reference the information provided for the browser version as you work your way through the submenus.
Chapter 12. Remote Terminal Operation SSH Terminal Session (Linux): To log in to the PN7212 / PN7320 by means of a secure SSH session, do the following: 1. Open a terminal (command line) on your computer. 2. At the prompt, key in your PN7212 / PN7320 Username and the PN7212 / PN7320's IP Address in the following way: ssh [username@IP Address] 3. Press Enter 4. When you are prompted for a password, use your PN7212 / PN7320 password.
PN7212 / PN7320 User Manual Third Party Utility (Windows): SSH sessions can be implemented under Windows with the use of third party utility software, such as PuTTY, a free implementation of Telnet and SSH for the Win32 and Unix platforms. To make an SSH connection with PuTTY, do the following: 1. In the Host Name box, enter the Internet host name or IP Address of the server you want to connect to. 2. Select SSH from the Protocol buttons. 3. Click Open (at the bottom of the dialog box) 4.
Appendix Safety Instructions General This product is for indoor use only. Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers.
PN7212 / PN7320 User Manual If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Appendix Consignes de sécurité Général Ce produit est destiné exclusivement à une utilisation à l’intérieur. Veuillez lire la totalité de ces instructions. Conservez-les afin de pouvoir vous y référer ultérieurement. Respectez l’ensemble des avertissements et instructions inscrits sur l’appareil. Ne placez jamais l’unité sur une surface instable (chariot, pied, table, etc.). Si l’unité venait à tomber, elle serait gravement endommagée. N’utilisez pas l’unité à proximité de l’eau.
PN7212 / PN7320 User Manual La prise murale doit être installée à proximité de l’équipement et doit être facile d’accès. Veillez à ce que rien ne repose sur le cordon d’alimentation ou les câbles. Acheminez le cordon d’alimentation et les câbles de sorte que personne ne puisse marcher ou trébucher dessus. En cas d’utilisation d’une rallonge avec cette unité, assurez-vous que le total des ampérages de tous les produits utilisés sur cette rallonge ne dépasse pas l’ampérage nominal de cette dernière.
Appendix Les performances de l’unité sont visiblement altérées, ce qui indique la nécessité d’une réparation. L’unité ne fonctionne pas normalement bien que les instructions d’utilisation soient respectées. N’utilisez que les commandes qui sont abordées dans le mode d’emploi. Le réglage incorrect d’autres commandes peut être à l’origine de dommages qui nécessiteront beaucoup de travail pour qu’un technicien qualifié puisse réparer l’unité.
PN7212 / PN7320 User Manual Rack Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack. Always load the rack from the bottom up, and load the heaviest item in the rack first. Make sure that the rack is level and stable before extending a device from the rack.
Appendix Montage sur bâti Avant de travailler sur le bâti, assurez-vous que les stabilisateurs sont bien fixées sur le bâti, qu’ils sont étendus au sol et que tout le poids du bâti repose sur le sol. Installez les stabilisateurs avant et latéraux sur un même bâti ou bien les stabilisateurs avant si plusieurs bâtis sont réunis, avant de travailler sur le bâti. Chargez toujours le bâti de bas en haut et chargez l’élément le plus lourd en premier.
PN7212 / PN7320 User Manual avec l’unité d’alimentation éco. L’utilisation de tout autre type système de fixation de câble pourrait s’avérer très dangereuse. Veuillez contacter votre revendeur ATEN pour plus d’informations sur le support de câble ATEN LokU-Plug.
Appendix Technical Support International For online technical support – including troubleshooting, documentation, and software updates: http://eservice.aten.com For telephone support, see Telephone Support, page iii North America Email Support Online Technical Support support@aten-usa.com Troubleshooting Documentation Software Updates Telephone Support http://www.aten-usa.
PN7212 / PN7320 User Manual IP Address Determination If you are an administrator logging in for the first time, you need to access the PN7212 / PN7320 in order to give it an IP address that users can connect to. There are two methods to choose from. In each case, your client computer must be on the same network segment as the PN7212 / PN7320. After you have connected and logged in you can give the device its fixed network address. (See Network, page 65.
Appendix 4. Select either Obtain an IP address automatically (DHCP), or Specify an IP address. If you chose the latter, fill the IP Address, Subnet Mask, and Gateway fields with the information appropriate to your network. 5. Click Set IP. 6. After the IP address shows up in the Device List, click Exit to end the program. Method 2: 1. Set your computer's IP address to 192.168.0.XXX Where XXX represents any number or numbers except 60. (192.168.0.60) is the default address of the PN7212 / PN7320.) 2.
PN7212 / PN7320 User Manual Trusted Certificates Overview When you try to log in to the device from your browser, a Security Alert message appears to inform you that the device’s certificate is not trusted, and asks if you want to proceed. The certificate can be trusted, but the alert is triggered because the certificate’s name is not found on Microsoft list of Trusted Authorities.
Appendix Installing the Certificate To install the certificate, do the following: 1. In the Security Alert dialog box, click View Certificate. The Certificate Information dialog box appears: Note: There is a red and white X logo over the certificate to indicate that it is not trusted. 2. Click Install Certificate. 3. Follow the Installation Wizard to complete the installation. Unless you have a specific reason to choose otherwise, accept the default options. 4.
PN7212 / PN7320 User Manual 5. Next, click Finish to complete the installation; then click OK to close the dialog box.
Appendix Mismatch Considerations If the site name or IP address used for generating the certificate no longer matches the current address of the switch a mismatch warning occurs: You can click Yes to go on, or you can disable mismatch checking. To disable mismatch checking, do the following: 1. After the page you are logging in to comes up open the browser’s Tools menu; Select Internet Options → Advanced. 2. Scroll to the bottom of the list and uncheck Warn about trusted certificates: 3. Click OK.
PN7212 / PN7320 User Manual Self-Signed Private Certificates If you wish to create your own self-signed encryption key and certificate, a free utility – openssl.exe – is available for download over the web at www.openssl.org. To create your private key and certificate do the following: 1. Go to the directory where you downloaded and extracted openssl.exe to. 2. Run openssl.exe with the following parameters: openssl req -new -newkey rsa:1024 -days 3653 -nodes -x509 -keyout CA.key -out CA.
Appendix Troubleshooting Overview Operation problems can be due to a variety of causes. The first step in solving them is to make sure that all cables are securely attached and seated completely in their sockets. In addition, updating the product’s firmware may solve problems that have been discovered and resolved since the prior version was released. If your product is not running the latest firmware version, we strongly recommend that you upgrade. See Firmware Upgrade, page 101, for upgrade details.
PN7212 / PN7320 User Manual Problem 2: The computer has an older mainboard that doesn't support APM in the BIOS. What can I do to get Safe Shutdown and Reboot working? Solution: If you are running Windows 2000, XP, or Server 2003, you can do the following: 1. Open Control Panel → Power Options. 2. Open Properties → APM. 3. Enable Advanced Power Management support.
Appendix Problem 4: Although my computers have been configured for a Safe Shutdown, some of them don't shut down. Solution: This may be due to the applications running on them putting up a dialog box asking if you want to save the information running on them before they close. Since you haven't provided an answer, the shutdown procedure doesn't continue to completion.
PN7212 / PN7320 User Manual Problem 8: The Log Server program does not run. Solution: The Log Server requires the Microsoft Jet OLEDB 4.0 driver in order to access the database. This driver is automatically installed with Windows ME, 2000, and XP. For Windows 98 and NT you will have to go to the Microsoft download site: http://www.microsoft.com/data/download.htm to retrieve the driver file: MDAC 2.7 RTM Refresh (2.70.9001.
Appendix Administrator Login Failure If you are unable to perform an Administrator login (because the Username and Password information has become corrupted, or you have forgotten it, for example), you can clear the login information with the following procedure: 1. Power off the PN7212 / PN7320 and remove its housing. 2. Short the jumper labeled J5. 3. Power on the switch. 4. When the Link and 10/100Mbps LEDs flash, power off the switch. 5. Remove the jumper cap from J6. 6.
PN7212 / PN7320 User Manual Specifications Function Power Outlets Connectors Direct Max Power Inlets NEMA (UL/PSE) Power Outlets IEC 320 (via Daisy Chain) 1 x NEMA L5-20P 1 x NEMA L5-30P 1 x IEC 60309 12 x NEMA 5-15R 3 x NEMA 5-20R 17 x NEMA 5-15R IEC 12 x IEC320 C13 3 x IEC320 C19 17 x IEC320 C13 PON In / Console 1 x RJ-45 (F) PON Out 1 x RJ-45 (F) Modem 1 x RJ-45 (F) LAN 1 x RJ-45 (F) ID 2 x RJ-11 (F) 1 x Terminal Block 1 x 2-digit 7-segment Station 1 x Green Outlet 1 x Green R
Appendix Function Measurement Voltage PN7212 Range PN7320 85VAC~250VAC Accuracy +/- 3% Range 85VAC~130VAC, 200VAC~250VAC Accuracy Power +/-3% Range (85V x 1A)85W ~ 5000W(250V x 20A) Accuracy Current +/- 5% @ Current >1A Irms Range 0.1A~1A Accuracy +/- 0.1A Range 1A~20A Accuracy Environment +/-3% Operating Temperature 0–50oC Storage Temperature -20–60oC Humidity Physical Properties 0–80% RH Noncondensing Housing Metal Weight 4.49 kg Dimensions (L x W x H) 5.68 kg 6.
PN7212 / PN7320 User Manual Null Modem Cable Diagrams 152
Appendix Limited Warranty ATEN warrants this product against defects in material or workmanship for a period of one (1) year from the date of purchase. If this product proves to be defective, contact ATEN's support department for repair or replacement of your unit. ATEN will not issue a refund. Return requests can not be processed without the original proof of purchase. When returning the product, you must ship the product in its original packaging or packaging that gives an equal degree of protection.
PN7212 / PN7320 User Manual This Page Intentionally Left Blank 154
Index A Access Outlet Level, 39 Station Level, 38 Access Ports, 65 Adding Users, 50 Administrator Login Failure, 149 ANMS, 69 E End Session, 38 Event Panel, 114 F Features, 2 Filtering IP, 87 MAC, 87 Firmware Upgrade, 101 Firmware upgrade recovery, 103 Forgotten Password, 149 B Backup, 104 Browser login, 23 C G Configuration, 40 Outlet Level, 44 Station Level, 40 Console Terminal Session, 115 Corrupt Password, 149 Creating Groups, 54 Customization, 91 D Daisy Chaining, 15 Date/Time, 92 Date/Time Sett
PN7212 / PN7320 User Manual L List Panel, 114 Log, 95 Log Event List, 96 Notification Settings, 99 Save, 98 Search, 97 System Log, 95 Log Server Configure, 109 Event Panel, 114 Events, 110 Installation, 107 List Panel, 114 Main Screen, 113 Menu Bar, 109 Options, 112 Starting Up, 108 Log server, 107 Logging in Browser, 23 Login Failures, 91 Login String, 87 M MAC Filtering, 87 Main Page, 24 Managing Groups, 54 Managing Users, 50 Manual Power Management, 29 Modem Session, 119 Modifying groups, 56 Modifying
Index Login string, 87 Self-signed certificates, 144 Sessions, 38 Settings Web refresh rate, 66 Setup network configuration, 20 Sidebar, 28 SJ/T 11364-2006, ii Specifications, 150 SSH terminal session (Linux), 127 third party utility (Windows), 128 System after AC Back, 147 System Log, 95 T Technical Support, 137 Telephone support, iii Telnet, 125 Time settings, 92 Troubleshooting, 145 Trusted Certificates, 140 U User interface Page components, 25 User Management, 49 User Notice, iii Users Adding, 50 as
