2/4-Port VGA Switch with Audio VS0201 / VS0401 User Manual www.aten.
VS0201 / VS0401 User Manual FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
VS0201 / VS0401 User Manual User Information Online Registration Be sure to register your product at our online support center: International http://support.aten.com North America http://www.aten-usa.
VS0201 / VS0401 User Manual Package Contents The VS0201 / VS0401 package consists of: 1 VS0201 / VS0401 2/4-Port VGA Switch with Audio 1 Power Adapter 1 User Instructions* Check to make sure that all the components are present and that nothing got damaged in shipping. If you encounter a problem, contact your dealer. Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit, and/or any of the devices connected to it.
VS0201 / VS0401 User Manual Contents FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Online Registration . . . . . .
VS0201 / VS0401 User Manual Dynamic DDC Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Pushbutton Lock Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Read Firmware Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Reset Device Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Appendix Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VS0201 / VS0401 User Manual About this Manual This User Manual is provided to help you get the most from your system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below. Chapter 1, Introduction, introduces you to the VS0201 / VS0401 system. Its purpose, features and benefits are presented, and its front and back panel components are described.
VS0201 / VS0401 User Manual Conventions This manual uses the following conventions: Monospaced Indicates text that you should key in. [] Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. 1. Numbered lists represent procedures with sequential steps. ♦ Bullet lists provide information, but do not involve sequential steps.
Chapter 1 Introduction Overview The VS0201 / VS0401 2/4-Port VGA Switch with Audio allows you to connect two/four source computers to a single monitor or projector with full audio and quickly switch between the devices for use. The convenient front panel pushbuttons and IR remote control allow you to easily toggle between VGA/Audio sources, while front panel LEDs indicate the connected source device at a glance.
VS0201 / VS0401 User Manual Features Displays the video output of two (VS0201) or four (VS0401) computers on a single monitor or projector Quick and easy switching between VGA/Audio sources via front panel pushbuttons, RS-232, or IR remote control Superior video quality – up to 1920 x 1440 Long-distance transmission – up to 65 m Supports– VGA, SVGA, UXGA, WUXGA, and multisync monitors Video DynaSync™ - Exclusive ATEN technology eliminates boot-up display problems and optimizes resolution when s
Chapter 1.
VS0201 / VS0401 User Manual Components VS0201 Front View 1 3 4 2 VS0401 Front View 1 3 4 2 No. Component Function 1 Port Selection Pushbuttons Pressing a port selection pushbutton routes the VGA/Audio source from the corresponding input port to the output port for display. 2 Port LEDs There is one port LED next to each port selection pushbutton. This lights green to indicate that the corresponding port has been selected.
Chapter 1. Introduction VS0201 Rear View 2 3 4 1 5 6 VS0401 Rear View 3 2 4 1 5 No. 6 Component Function 1 Grounding Terminal The grounding wire used to ground the unit attaches here. 2 RS-232 Serial Port This is the serial remote port for input source selection and high-end system control. 3 External IR Receiver Port Connect the IR Receiver to this port. 4 Video / Audio Input Each input section is comprised of a VGA connector and a mini stereo audio jack.
VS0201 / VS0401 User Manual This Page Intentionally Left Blank 6
Chapter 2 Hardware Setup 1. Important safety information regarding the placement of this device is provided on page 19. Please review it before proceeding. 2. Make sure that the power to all devices connected to the installation are turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. Installation Installation of the VS0201 / VS0401 is simply a matter of plugging in the appropriate cables.
VS0201 / VS0401 User Manual Note: The VS0201 and VS0401 installations are the same, with the only difference being that the VS0401 has two additional source ports. Installation Diagram 2 5 6 3 4 1 OR Installing the RS-232 Controller In order to use the RS-232 serial interface to attach a high-end controller (such as a PC) to the VS0201 / VS0401, use a RS-232 serial cable. The end connecting to the VS0201 / VS0401 should have a 9-pin male connector. Refer to step 5 on the diagram above.
Chapter 3 Operation Overview The VS0201 / VS0401 2/4-Port VGA Switch with Audio offers easy source device selection with either the front panel pushbuttons, IR remote control, or RS-232 serial interface. This chapter describes Source Selection, Power on Detection mode, Pushbutton Lock, Powering Off/Restarting, and the RS-232 serial port configuration and commands. Note: Whenever the VS0201 / VS0401 is powered on, it automatically remembers the last connected port being used and connects to it.
VS0201 / VS0401 User Manual Power On Detection The Power On Detection feature enables the VS0201 / VS0401 to do the following: Automatically switches to the next port with a powered on source device connected, when the current active port device is powered off. When the VS0201 / VS0401 is turned on, the port last connected when the device was turned off will be selected.
Chapter 3. Operation RS-232 Serial Interface The VS0201 / VS0401’s built-in bi-directional RS-232 serial interface allows system control through a high-end controller, PC, and/or home automation / home theater software package.
VS0201 / VS0401 User Manual Switch Port Commands The formulas for Switch Port commands are as follows: 1. Switch Command + Input Command + Port Number [Enter] For example, to switch the input port to port 02, type the following: sw i02 [Enter] 2.
Chapter 3. Operation Auto Switch Commands The Auto Switch command places priority on a port so that when a source is connected to that port the VS0201 / VS0401 automatically switches to it, and the port can not be changed until the source is unplugged or auto switching is disabled. The formulas for Auto Switch commands are as follows: 1. Switch Command + Input Command + Port Number + Control [Enter] For example, to enable auto switching on port 02, type the following: sw i02 auto [Enter] 2.
VS0201 / VS0401 User Manual Power On Detection Commands The Power On Detection feature switches ports when the connected device is powered off (See Power On Detection, page 10, for details).
Chapter 3. Operation Dynamic DDC Commands The Dynamic DDC feature is used to monitor the connected display and provide the correct updated EDID information to the source device so that the display is optimized. With Dynamic DDC off, source devices do not receive updated EDID data which can cause display issues. If there is a problem with your display quality, it is recommended that Dynamic DDC be turned off.
VS0201 / VS0401 User Manual Pushbutton Lock Commands The Pushbutton Lock feature allows you to secure your device by locking use of the front panel push-buttons.
Chapter 3. Operation Read Firmware Command The Read Firmware feature allows you to read the firmware information of the VS0201 / VS0401.
VS0201 / VS0401 User Manual Reset Device Command The Reset feature resets the VS0201 / VS0401 back to the factory default settings. The formula for the Rest commands is as follows: Command [Enter] For example, to reset back to the factory default settings, input the following: reset [Enter] The following tables show the possible values and formats for the command: Command reset Description Resets the device back to the factory default settings Note: Each command can be separated with a space.
Appendix Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation.
VS0201 / VS0401 User Manual If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or un-interruptible power supply (UPS).
Appendix Technical Support International For online technical support – including troubleshooting, documentation, and software updates: http://support.aten.com For telephone support, Telephone Support, page iii North America Email Support Online Technical Support support@aten-usa.com Troubleshooting Documentation Software Updates Telephone Support http://www.aten-usa.
VS0201 / VS0401 User Manual Specifications Function VS0201 VS0401 2 4 Video 2 x HDB-15 Male (Blue) 4 x HDB-15 Male (Blue) Audio 2 x Mini Stereo Jack Female (Green) 4 x Mini Stereo Jack Female (Green) Video 1 x HDB-15 Female (Blue) 1 x HDB-15 Female (Blue) Audio 1 x Mini Stereo Jack Female (Green) 1 x Mini Stereo Jack Female (Green) Display Connections Connectors Input Output RS-232 Port 1 x DB-9 Female (Black) IR Input port 1 x Mini Stereo Jack Female (Black) Power Switches Port Se
Appendix Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
