0x13 FT Item no. A Reference Image B X4 X2 B1 X2 C X2 C1 X2 Ea X4 E1 X6 G G1 Qty.
Item no. G2 ASSEMBLY INSTRUCTIONS Reference Image X2 G6 Qty. D1 X4 Eb F D2 E2 X4 H1 X4 X2 K1 X4 L H X6 K X6 F3 G3 Qty. X2 X4 F4 Item no. Reference Image G5 F1 F2 X4 X2 G4 Item no. Reference Image Qty.
Item no. Reference Image Qty. P X4 S X4 J T Q Q1 Q2 Q3 Q4 Q5 Q6 R1 R2 R3 ASSEMBLY INSTRUCTIONS Item no. Reference Image W2 W3 X4 M6X15mm 3 M5X12mm 4 X4 ST4.8X12mm 5 X4 6 X4 M6X25mm 8 X4 9 X4 10 X4 X4 3 X168 X16 X24 X24 X2 X1 7 X4 X2 M6X16mm 2 X4 X6 X4 1 X4 Qty.
ASSEMBLY INSTRUCTIONS 1 X4 A 4pcs J 4pcs 1 12pcs A 1 1 1 A J J 4
2 X2 ASSEMBLY INSTRUCTIONS B 2pcs B1 2pcs C 2pcs C1 2pcs P 4pcs 1 32pcs U 112pcs When connecting B and B1 via P,C and C1 via P, make sure that 1 holes on part P (as shown in the picture) should be facing upwards. Do not install it upside down.
ASSEMBLY INSTRUCTIONS 3 1 16pcs 2 16pcs B1 C C1 A C1 B A C B1 2 C B1 A 2 B A 2 C 2 A 1 6 A B1
ASSEMBLY INSTRUCTIONS 4 H 4pcs H14pcs 1 16pcs H H1 H H1 H1 H H H1 1 7 H A H1 1
ASSEMBLY INSTRUCTIONS 5 K K K1 4pcs 4pcs 4 24pcs K 3 4pcs K1 K1 K K1 K1 K 4 4 K K1 3 8 4
ASSEMBLY INSTRUCTIONS 6 L 1pc 6 6 1pc 1 L 6 L 6 2 9
7 X4 ASSEMBLY INSTRUCTIONS Ea4pcs Eb4pcs D1 4pcs 1 8pcs 10 8pcs W3 4pcs 3 8pcs 10 Ea Eb 1 Eb D1 Ea 3 W3 Ea
8 ASSEMBLY INSTRUCTIONS 1 12pcs Ea Ea Ea Ea Ea Eb 1 L 1 A Eb 10
9 X6 ASSEMBLY INSTRUCTIONS E1 6pcs E2 6pcs D2 6pcs 3 1 24pcs W36pcs 3 12pcs W3 E1 E1 E1 E2 1 E2 1 12 D2
ASSEMBLY INSTRUCTIONS 10 1 Ea 18pcs E1 E1 Ea E1 E2 L E2 E2 Ea Ea 1 E1 Ea E1 Ea E1 E1 1 13
11 ASSEMBLY INSTRUCTIONS M 1pc 5 M 2pcs 7 1pc L 7 5 14 5
12 ASSEMBLY INSTRUCTIONS G5 2pcs G6 2pcs N 4pcs 1 1 10pcs G5 E1 E1 Ea E1 G6 Ea G6 G5 15 Ea E1 G5 G6 Ea N E1 E1 E1 Ea
13 ASSEMBLY INSTRUCTIONS R1 4pcs R2 4pcs R3 2pcs Eb Eb R1 R2 R2 R1 R3 R3 R1 R2 R2 R1 16 E2 E2 Before installing Parts R1/R2/R3, remove protective films (with side marks) on both the front and back sides. After removal, there will be no mark and minimal difference between the sides. Therefore, pay close attention to directions before removal.
14 ASSEMBLY INSTRUCTIONS G3 2pcs G4 2pcs N 4pcs 1 10pcs Ea G3 G4 N E1 G4 1 G4 G3 1 G4 17 G3
15 ASSEMBLY INSTRUCTIONS F 2pcs F1 4pcs F2 4pcs Q 2pcs Q14pcs Q24pcs E1 Q1 Q2 Q Q1 Q1 Q2 Ea F1 E1 Q1 F1 F2 F1 F2 Q1 Q2 F1 F1 F Q2 Q1 Q Q F Q1 Q2 Ea F2 Q2 Q1 F1 F2 18 F1 Q1 E1 Before installing Parts Q/Q1/Q2, remove protective films (with side marks) on both the front and back sides. After removal, there will be no mark and minimal difference between the sides. Therefore, pay close attention to directions before removal.
ASSEMBLY INSTRUCTIONS 16 Q Q5 Q3 2pcs Q34pcs Q1 Q2 Q4 Q1 Q6 Q5 Q Q3 Q2 Q Q4 Q3 Q6 Q5 F4 F4 Q5 Q6 Q3 F3 F3 Q1 Q4 Q2 Q6 Q5 F4 Q4 Q2 R1 R2 R2 R1 Q1 Q3 Q Q R3 R3 Q Q F4 4pcs Q44pcs Q54pcs Q64pcs F3 4pcs Q3 Q1 R1 R2 R2 R1 Q2 Q4 F4 Q5 Q6 Q1 Q3 F4 F3 19 Q1 E1 Q3 Ea Q2 Q4 Q6 Ea Q5 F3 Q5 R1 Q3 Q1 R1 E1 Before installing Parts Q/Q3/Q4, Q5/Q6remove protective films (with side marks) on both the front and back sides.
17 ASSEMBLY INSTRUCTIONS G 2pcs G1 4pcs G2 4pcs N 4pcs N16pcs Ea G2 E1 N1 G2 N1 G 1 N1 G1 N G1 G2 G2 G1 N1 N1 1 10pcs G1 N N 1 N G1 N1 G N1 20 G2 N
18 ASSEMBLY INSTRUCTIONS T 4pcs T T T T U U Pay attention to the sidewall curtain's installation position.
19 ASSEMBLY INSTRUCTIONS S 4pcs S S 2 1 3 Note: Attach 1 to 2 to secure parts S (netting) and T (curtains) together. Attach 1 to 3 to secure the back curtain (T). Attach 1 to 3 to secure the front netting (S). U U Pay attention to the sidewall netting's installation position. 22 S Hang the hook attached to the netting on Part A.
20 ASSEMBLY INSTRUCTIONS 8 12pcs Installation Completed A 8 A J 8 J Cement surfaces To improve wind resistance, be sure to complete this installation step. If expansion screws or ground nails are not installed,strong winds may topple the gazebo. 23 Expansion screws are essential for stability on cement surfaces, All are included in the accessories package.
