User's Manual C K6 Bluetooth Speakerphone
1 About CK6 Bluetooth Speakerphone This versatile Bluetooth speakerphone is portable and specially designed for the user to enjoy convenience and freedom of wireless communication. Dual capacity of use on desk-top like a conference Speakerphone and in-car like a Hands-Free car kit. CK6 built advanced DSP technology for Echo Cancellation & Noise Suppression, provides you excellent full duplex sound quality. 2 About Bluetooth Technology Bluetooth is a short-range wireless communication technology.
Getting Started To use your Bluetooth speakerphone, please follow these simple steps: a) Charge your speakerphone. Before using the speakerphone, it is recommended to charge the battery fully for the first time. Normally charge the battery fully need take approx 3 hours. b) Put the speakerphone close to a Bluetooth-enabled mobile phone less than1 meter distance for pairing operation. c) Ensure your speakerphone and handset is within 10 meters Bluetooth connection distance. 7 6 1 5 4 3 2 1.
Installation - Sun Visor 3
4 Charging the battery This device has an replaceable, rechargeable battery, it is compatible with Nokia BL-5B battery. But you are recommand to use the original accessary or approved battery by supplier. 1. For first time use, please fully charge the speakerphone. 2. Plug the car charger into the car lighter socket and put the MINI USB plug into the socket of the speakerphone. 3. While the charger is connected, the red indicator light is displayed during charging.
Important: It is recommended that you fully charge the speakerphone before leaving it unused for along time. To prevent overdischarge endangers the battery, you are recommended to fully charge the speakerphone each 2 months. 6 Turning On/Off the CK6 Turning On When the CK6 is turned off, press and hold the MFB for 3 seconds until you hear a short beep, the LED indicator will be solid blue for 3 seconds. The CK6 is now turned on.
(b) Ensure the CK6 is turned OFF . (c) Press and hold the MFB for 6 seconds until you see the LED flashes Red and Blue alternately and you will hear a long beep, it is now ready for pairing. (E) Select "CK6" from the list. (f ) Enter the PIN code "0000" and confirm to complete pairing. When pairing is completed the CK6 will connecte to your phone automatically, you may hear a long beep and LED indicator will flash blue 3 times. In standby state, the LED indicator will flash blue 1 time every 3 seconds.
Make Connectio n/Link to Mobile phone: After pairing is completed, if the CK6 is not connected to mobile phone, please follow the simple steps to activate the Bluetooth connection/link: 1.If your CK6 has finished the pairing operation successfully, when the CK6 is turned on, it will connect to the phone(s) you last connected automatically, but make sure your phone's Bluetooth function is active. 2.The CK6 supports multi-point and connects to 2 phones at the same time.
10 Using the CK6 After the pairing is completed and battery is fully charged, please follow the bellow instruction to use the CK6. (a) Answering a Call: When you receive an incoming call, press MFB shortly to answer the call or answer the call via your mobile phone by the normal way. (b) Ending a Call: Shortly press MFB to end your call or end the call via your mobile phone by the normal way.
(e)Last Number Re-Dialing: In the stand-by mode, Press and hold Volume Down button for 2 seconds, you will hear 2 short tones, the last number you dialed will be re-dial out. If the CK6 has connected to 2 phones, press and hold Volume Up button for 2 seconds will start last number re-dialing of phone 2.
Reset the paired device(s) lis t and the last/default user You may want to reset the CK6 to its original settings and clear the previous pairing. Please follow these simple steps. (a)Ensure the CK6 is under standby mode. (b)Press and hold the "V+"& "V-" buttons for 10 sec. until LED flashes blue & red at the same time. Release the buttons, the paired list of CK6 has been clear.
LED Indication Red LED Status Blue LED Solid on for 3 seconds Power On Power Off Solid on for 3 seconds Middle low beep Long low beep Flashes 1 time every 3 seconds Standby after Pairing Standby Low Voltage Sound Flashes 1 time every 3 seconds 3 beeps every one minute Flashes 1 time every 15 seconds In Talking Progress Pairing in Progress Flashes Red and Blue alternately Flashes on every 3 seconds Pairing Completed Mute Solid on Charging in Progress Solid on Charging Completed Off Long
Safety and general informatio n 1.Please read this User's Manual carefully and follow all instructions. 2.To avoid any damage or malfunction of the device do not drop the device from high places. 3.Keep device away form humidity, water and any other liquid. If the device is exposed to water, moisture and other liquids do not operate it to avoid any electrical shock, explosion and damage to the device or yourself. 4.
Trouble Shooting If you are unable to connect your CK6 and mobile phone, please try the following: (a) Ensure the CK6 is paired with your mobile phone. (b) Ensure your mobile phone's Bluetooth feature is activated. Please refer to your mobile phone user guide for specific instruction. (c) Ensure the CK6 is within a maximum of 10 meters of your mobile phone(s) and there are no obstructions, such as wall or other electronic devices in between as it may cause shorter or interference transmission.
Product Specifications Bluetooth Specifications Version 2.1, Class 2, 10 Meters Bluetooth Profile Supported Headset & Hands-Free Profiles Operating Frequency Band 2.402 to 2.480GHz unlicensed ISM band Dimension 120(L)x60(W)x16.5(H) mm Weight 61g Normal Charge Time 3 hrs.(approx.) Talk Time Up to 6 hrs. Standby Time Up to 300 hrs Rechargeable Li-ion Battery 3.
FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
