User's Manual
24
ENGLISH
25
Activate the Bluetooth function of the cell phone and start the search
for Bluetooth devices. (For further details, please read the operating
instructions of your cell phone.).
Select "BT DF 211" from the displayed list.
If necessary, enter the PIN code "0000" and con rm the entry. After suc-
cessful pairing, you hear a long signal sound and the MF button ashes
blue 5 times. The BT Drive Free 211 automatically connects with the cell
phone and changes to standby mode a few seconds later. In standby
mode, the MF button ashes blue 2 times every 5 seconds. (Note: The
PIN code is preprogrammed and cannot be changed)
In standby mode, brie y press the MF button to re-establish the connec-
tion. The connection can be established only if the BT Drive Free 211 is
no further away from the cell phone than 10 metres.
Note: If the pairing is not completed within 2 minutes, the BT Drive Free 211
switches o again. In this case, restart the pairing to connect the BT Drive
Free 211 with the cell phone.
Using the BT Drive Free 211
If the headset is in the docking station, it works together with the docking
station as hands-free system. The headset can also be used separately for
phone calls.
After the pairing has been successfully completed and the battery has been
charged, the following functions can be performed:
Making a call
Using voice dial
The cell phone must support the voice dial function and the function
must be activated. The corresponding voice commands for the contacts
must be recorded in the cell phone. You nd the pertinent information
in the operating instructions of the cell phone.
If the BT Drive Free 211 is in standby mode, brie y press the MF button.
You will hear a short signal sound and the cell phone asks you to say the
voice command which you recorded in the cell phone for the correspond-
ing contact. If the voice command is recognised by your cell phone, the
number associated with it is dialled.
Redialling the last number
In the standby mode, press the MF button twice. You hear a signal sound
and the number dialled last is dialled again.
–
–
–
–
–
–
Answering a call
To answer an incoming call, brie y press the MF button or the call button
of the cell phone.
Ending a call
Brie y press the MF button or the end call button of the cell phone to end
a call.
Rejecting a call
To reject an incoming call, press the MF button until you hear a new signal
sound.
Transferring a call
To transfer a call from the cell phone to the headset, press the MF button
during the call until you hear a signal sound. Repeat the process to transfer
the call again from the headset to the cell phone.
Adjusting the volume
During a phone call, you can adjust the volume with the buttons "+" and "–".
You can also set the volume via the volume buttons of the cell phone.
Muting the microphone
During a phone call, press the "–" button until you hear 2 signal sounds.
The microphone of the headset is muted. At an interval of 20 seconds, the
MF button lights up red 2 times and you hear 2 long signal sounds that
indicate that the microphone is muted, but the phone call is still active.
Repeat the operating step to reactivate the microphone.
Troubleshooting
If a connection between BT Drive Free 211 Bluetooth car kit and a cell phone
cannot be established, try the following rst:
Check whether the Bluetooth car kit is connected with the cell phone.
Ensure that the Bluetooth function of the cell phone is activated. You
nd more detailed information in the operating instructions of the cell
phone.
Ensure that the distance between Bluetooth car kit and cell phone is
less than 10 metres. There may not be any obstacles in between, such as
walls or electronic devices which could interfere with the transmission
or reduce the range.
If these steps should not lead to a solution for the problem, remove the
battery from the docking station for a few minutes. If need be, contact
the Service Centre of your dealer.
–
–
–
–
02_BTDriveFree211_gb.indd 24-25
02_BTDriveFree211_gb.indd 24-25
01.04.2011 17:36:08 Uhr
01.04.2011 17:36:08 Uhr