BTSP044 Bluetooth Speaker User’s Manual 1
1. Notice Before Using Thank you for purchasing the Bluetooth® speaker BTSP044 . Please read this User's Manual completely before use. BTSP044 designed for enjoy the high quality music wirelessly with a carriable size that based on the latest Bluetooth® wireless technology. BTSP044 can be easily connected to a mobile phone for call conversation and music listening, it is also capable to connect to the other Bluetooth®‐enabled devices like Notebook, iPod etc. BTSP044 is compliant with Bluetooth V2.
. BTSP044 Bluetooth speaker overview ① Microphone ② Answer ③ Indicator LED ④ Charging Port ⑤ AUX IN port ⑥ ON/OFF Switch 4.
5. Battery information The device is equipped with an integrated lithium‐polymer battery. The battery cannot be replaced. Do not attempt to remove the battery from the device since it would damage the device. The full performance of a new battery is not achieved until after two or three complete charging‐discharging cycles. The battery can be charged and discharged several hundred times, but it looses its capacity over time.
3) When the charger is connected to the speaker, the red indicator light will turn on. Charging the battery fully may take up to 3 hours. ① ② ③ 4) Micro Connector USB A Connector Micro USB Charge Port When the battery is fully charged, the red indicator light will turn off. Disconnect the charger from the speaker and the outlet. The speaker is ready to use. NOTE: ‐ Give your speaker a full charge before using for the first time.
1) 2) 3) 4) 5) Keep the BTSP044 within 1 meter range of a Bluetooth®‐ready Mobile phone. Slide the Power Switch to On positon, the indicator flashes red and blue intermittently, the device is now in pairing mode. Find the Bluetooth® setting of your Mobile phone and start the search for Bluetooth® devices. (For further details, please read the operating instructions of your Mobile phone). From the list of devices found, select the " BTSP044". If required, enter the PIN code "0000" and confirm the entry.
are turned on, it will connect to the phone you last connected to automatically. Please ensure your phone's Bluetooth® function is active. Turn off the speaker Slide the switch to OFF position to power down your device. Note: 1) To conserve power, if the speaker is not connected to any mobile phone, it will enter paring mode, and turn off automatically 10 minutes later . You should toggle the power switch again to turn on the speaker.
The BTSP044 supports A2DP profile that allows stereo music to stream from a Bluetooth phone. The music will pause automatically while a call is dialed incoming, and resume when the call has ended. 10. Using for phone call Last number re‐dialing Press and hold ANSWER button for 2 seconds, the last number you dialed will be re‐dialed. Answering a call Press Answer button to answer the incoming call. Ending a call Press the Answer button to end a call. 11.
5) 6) 7) 8) 9) Do not modify, repair or disassemble device (Especially the battery). Doing this will void the warranty. Do not place heavy objects on the device. Use only the supplied and approved chargers. Unplug this device when unused for long periods of time or during lightening storms. The battery used in this device may present a risk of fire or chemical burn if mistreated. 12.
Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. This product is CE certified according to the provision of the R&TTE Directive (99/5/EC). This declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
‐ Specifically exempt from any warranty are limited‐life consumable components subject to normal wear and tear such as batteries, decorates and other accessories. ‐ Supplier is not responsible, for failure resulting from accident, abuse, misuse, or any unauthorized repair, or modification. ‐ Modification and repair of the unit should be done by an authorized and qualified service center or returned to the manufacturer.