H901A Bluetooth Headset
1 , What s in the box The headset contains the follo wing parts: 1. 2. 3. 4. 5. 6. 7. 8. Speaker Multi-function Button Indicator Light Microphone Volume Up Button Volume Down Button Charging Socket Ear Hook Package contents list: 1 H901A B luetooth Headset 2. Travel Charger 3. USB Charging Cable 4.
2 Pair to your Bluetooth phone Before you use your headset the firs t tim e, you must pair the unit with a Bluetooth device e.g. Bluetooth mobile phone. This operatio n guide based on the Bluetooth phone as the host's device. Please refer to the follo wing step to set up the pairin g: 1 2 Ensure the headset is off. 4 3 Press and hold the MFB for 4 seconds until you see the Blue and Red LED light flash alternately to enterthe pairing mode.
NOTE: l If the pairing is successful, the headset will connect to your phone automatically, you may need to confirm the enquiry. l While the headset is paired with the phone and connected, the indication light will flash 2 times every 5 seconds. If failed or didn't connect to the phone, the blue indicator light will flash 1 time every 3 seconds.
3 Charging the battery This headset has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. Please refer to the following step to charge the battery: 1. Connect the charger to the correct outlet. 2. When the charger is connected to headset, the red indicator light will turn on during charging. Charging the battery fully may take up to 2 hours. 3. When the battery is fully charged, the red indicator light will turn off.
4 Battery informatio n Your device is powered by a chargeable battery. The full performance of a new battery 's an achieved only afte r two or three complete charge and disc harge cycle. The battery can be charged and disc harged hundreds of tim es, but it will eventually wear out. Unplug the charger from the electric al plug and the device when not in use. Do not leave a fully charged battery connected to a charger, since overcharging may shorte n its life tim e.
*Turn off the headset At any working state after the headset turns on, press and hold MFB for 4 seconds, you will hear a melody from high to low, and the Red indicator light will flash 3 times at the same time, the headset turns off. Note l For saving the power, while the headset didn't connect to any device over 1 hour, the headset will turn off automatically. 6 Wearing your headset The headset can be worn on either the Left or Right ear.
7 Making a call * By phone's keypad At the stand-by state, dial the number on your phone dire ctly to make a call. * Use Voice- Dialin g At the stand-by state, press the MFB shortly , you will hear a short tone from the headset, and the phone will prompt you say the voice tag lik e your frie nd's name. If the voice tag is identifie d by the phone, the related number will be dial-o ut later.
8 Ending a call When in the callin g, press the MFB shortly will end the call, also you can end call on your mobile . 9 Reject an incoming call When you receive an incoming call, press and hold MFB for 2 seconds will reject the incoming call. 10 Answering a call When you receive an incoming call, press the MFB shortly can pick up the incoming call; also you can pick up the call on your mobile.
* While you are in the calling and another call was holding on, press MFB shortly can end current call and resume the holding on calling. * While you are in the calling and another call was holding on, press and hold MFB for 2 seconds can shift the current calling to the holding on calling. * While you are in the calling and another call was holding on, press Volume Up button shortly can add the holding on call to the current conversation to make a multiparty call.
15 Warranty The conditio n of this warranty and our responsibilitie s under this warranty are as follo ws: Warranty is non-transferable and is lim ite d to the orig inal purchaser only. * You must be able to prove the date of orig inal purchase of the unit with a dated receipt. * The warranty is not applic able if the product has been subject to physical abuse, improper installa tio n, modific atio n or repair by unauthoriz ed third party .
FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
