Assembly Instructions

ManualsBrandsAtlantic Furniture ManualsBunk & Loft BedsColumbia Bunk Bed Full Over Full with 2 Urban Bed Drawers in Walnut

Size of Mattress and Foundation

The length and width of the upper and lower bunk mattress and foundation are as follows :

Width

37 ½”- 38 ½”

52”- 53”

LengthSize

74”- 75”

Twin

Full

Thickness

9 ½” max

You must use only this size mattress.

Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½”

and that the mattress is at least 5” below upper edge of guardrails.

This Bunk Bed uses a slat kit for mattress foundation.

Replacement Parts

Replacement parts, including additional guardrails, may be obtained from any

Atlantic Furniture dealer

SAFETY WARNINGS

! !

( 1 )

( 2 )

( 3 )

( 4 )

( 5 )

( 6 )

( 7 )

( 8 )

( 9 )

(10)

(11)

(12)

(13)

Follow the information on the warnings appearing on the upper bunk end structure

and on the carton. Do not remove warning label from bed.

Always use the recommended size mattresses or mattress support, or both,

to help prevent the likehood of entrapment or falls.

Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.

Do not allow children under 6 years of age to use the upper bunk.

Periodically check and ensure that the guardrail, ladder, and other component are

in their proper position, free from damage, and that all connectors are tight.

Do not allow horseplay on or under the bed and prohibit jumping on the bed.

Always use ladder for entering or leaving upper bunk.

Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

Use of a night light may provide added safety precaution for a child using the upper bunk.

Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed

next to the wall, the guardrail that runs the full length of the bed should be placed against

the wall to prevent entrapment between the bed and the wall.

The use of water or sleep flotation mattresses is prohibited.

STRANGULATION HAZARD : Never attach or hang items to any part of the bunk bed

that are not designed for use with the bed; for example, but not limited to, hooks, belts

and jump ropes.

Keep these instructions for future reference.

Page 1 of 8

BUNK SAFETY WARNING

Summary of content (8 pages)

PAGE 1
Size of Mattress and Foundation The length and width of the upper and lower bunk mattress and foundation are as follows : Size Twin Full Length 74”- 75” 74”- 75” Width 37 ½”- 38 ½” 52”- 53” Thickness 9 ½” max 9 ½” max You must use only this size mattress. Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½” and that the mattress is at least 5” below upper edge of guardrails. This Bunk Bed uses a slat kit for mattress foundation.
PAGE 2
READY COLUMBIA BUNK BED ASSEMBLY INSTRUCTIONS (TWIN - TWIN) (TWIN - FULL) (FULL - FULL) Thank you for choosing Atlantic’s Bunk Bed. This practical design offers the utmost in versatility. Before assembling your Columbia bunk bed, please read through these instructions carefully. Familiarize yourself with the different parts. Please note that you will require a Phillips head screwdriver and an Allen wrench.
PAGE 3
PARTS LIST 07 02 TWIN OVER FULL SHOWN 06 08 04 05 06 09 07 08 03 08 02 03 10 08 01 01 HARDWARE 02 UPPER PANEL 03 LOWER PANEL 04 FULL GUARD RAIL 05 3/4 GUARD RAIL 06 LEFT END CAPS 07 RIGHT END CAPS 08 LONG RAIL 09 TWIN SLAT KIT OR FULL UPPER BUNK SLAT KIT 1 BOX FULL LOWER BUNK SLAT KIT OR TWIN LOWER BUNK SLAT KIT 1 BOX 10 COLUMBIA BUNK BED 1 BOX 1 BOX 1 BOX 1 BOX 1 BOX Page 3 of 8
PAGE 4
STEP 1 Attach the long rails (08) to the upper panels (02), using JCB M6 X 3 ½” (A), and barrel nut (C). Tighten with the Allen wrench (G). 02 A JCB M6 X 3 ½” A C 08 C C Barrel Nut 08 G C C Allen wrench A 02 A Adult Assembly STEP 2 If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall.
PAGE 5
STEP 3 Lay the twin slat kit (09) onto the bed. Fix in place using wood screws provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit. Adult Assembly 09 Customer Supplied Phillips head screwdriver Twin size shown Full Upper panel uses Full upper slat kit STEP 4 Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood screws (D). Tighten with the Phillips head screwdriver.
PAGE 6
STEP 5 Attach the long rails (08) to the lower panel (03), using JCB M6 X 3 ½” (A), and barrel nut (C). Tighten with the Allen wrench (G). 03 A A JCB M6 X 3 ½” C 08 A C C Barrel Nut C 03 08 G A C Allen wrench A Adult Assembly STEP 6 Lay the slat kit with center support (10) onto the bed, and fix in place using wood screws provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instuctions included with slat kit.
PAGE 7
STEP 7 Insert metal pins (E) into the holes in top of the lower panels. Lift the upper panels onto the lower panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs. E E Adult Assembly TWIN-TWIN E E Metal Pins TWIN-FULL ! CAUTION This step requires two strong people. STEP 8 FULL-FULL Cover holes with wood buttons (F)(Twin Full, Full Full ). Adult Assembly F F Wood Button F Customer Supplied F Phillips head screwdriver Lastly, install Ladder.
PAGE 8
CONVERSION TO 2 TWIN OR 2 FULL BEDS. STEP 9 Disassemble upper bunk by removing guard rails. Also remove metal pin from lower bunk. Metal Pin UPPER BUNK LOWER BUNK Disassemble upper bunk by removing upper panel (02) and lower bunk by removing lower panel(03). Exchange upper panel to the lower panel position and Install hardware tighten with Allen wrench. 02 03 UPPER BUNK LOWER BUNK F F STEP 10 F F Use Wood button (F) to cover holes as shown.