50-Port Dual Web Rack Switch A02-F48-4G USER’S MANUAL A02-F48-4G_ME01
50-Port Dual Web Rack Switch Copyright The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned mat be trademarks or registered trademarks of their respective owners. Subject to change without notice. No liability for technical errors and/or omissions. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
50-Port Dual Web Rack Switch TABLE OF CONTENTS CHAPTER 1............................................... 1 1.1 ABOUT THIS GUIDE ........................................................................................................................ 1 1.2 TERMS/USAGE ................................................................................................................................ 1 1.3 SWITCH FEATURES ..............................................................................................
0-Port Dual Web Rack Switch Reset Settings ................................................................................................................................. 23 Logout ............................................................................................................................................ 23 APPENDIX A ........................................... 24 RJ-45 PIN SPECIFICATION .....................................................................................................
50-Port Dual Web Rack Switch Chapter 1 Introduction 1.1 About This Guide Congratulations on your purchase of the 48+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch. This device integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. This guide discusses how to install your 48+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch. 1.
internetworking technologies. And with expected advances in the and digital signal processing that will enable Gigabit Ethernet to twisted-pair (UTP) cabling, outfitting your network with backbone/server connection creates a flexible foundation for technology products.
50-Port Dual Web Rack Switch QoS QoS gives you full control over which types of outgoing data traffic should be given priority by the Switch, ensuring important data like gaming packets move through the Switch at lightning speed, even under heavy load. 1.
50-Port Dual Web Rack Switch Chapter 2 Installation This chapter provides unpacking and installation information for the Switch. 2.1 Package Contents Open the shipping cartons of the Switch and carefully unpacks its contents.
50-Port Dual Web Rack Switch Combine the Switch with the provided screws Then, use screws provided with the equipment rack to mount each switch in the rack. Mount the Switch in the rack 2.4 Connecting Network Cable The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both in half and full duplex mode using two pair of Category 5 cable.
50-Port Dual Web Rack Switch Product Code Description Standards Network Media Connector Technology 10 Base T 100 Base TX 1000 Base T 1000 Base SX 1000 Base SX A02-MSW2(Fiber module) Giga Ethernet Fiber Module 1000BASE-SX 50µm or 62.5µm multimode optical fibers LC Connector RJ45 RJ45 RJ45 LC (62.5µm multimode optical fibers) LC (50µm multimode optical fibers) Distance 100m 100m 100m 275m 550m 2.5 AC Power The Switch used the AC power supply 100-240V AC, 50-60 Hz.
50-Port Dual Web Rack Switch The Switch is equipped with two Gigabit twisted pair ports, supported auto negotiable 10/100/1000Mbps and auto MDI/MDIX crossover detection function. These two ports can operate in half-duplex mode for 10/100Mbps and full- duplex mode for 10/100/1000Mbps. When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.
50-Port Dual Web Rack Switch Led SYSTEM Blinking : When the CPU is working, the System LED is blinking. On/Off : The CPU is not working. Ports 1~48 10/100M Status LEDs Link/ACT: Link/Activity On : When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. Blinking : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. Off : No link.
50-Port Dual Web Rack Switch Chapter 3 Configuration Through the Web Browser you can configure the Switch such as VLAN, Trunking, QoS… etc. With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware. 3.1 Installing the Web Management Utility The following gives instructions guiding you through the installations of the Web Management utility. 1. Insert the Utility CD in the CD-Rom Drive. 2.
50-Port Dual Web Rack Switch Discovery List This is the list where you can discover all the Web management devices in the entire network. By pressing the “Discovery” button, you can list all the Web Management devices in the discovery list. Double click or press the “Add to monitor list” button to select a device from the Discovery List to the Monitor List. System word definitions in the Discovery List: • • • • • • • • • MAC Address: Shows the device MAC Address.
50-Port Dual Web Rack Switch Monitor List All the Web Smart Device in the Monitor List can be monitored; you can also receive the trap and show the status of the device. System word definitions in the Monitor List: • • • • • • • • • • represent for device system is not S: Shows the system symbol of the Web-Smart device, alive. IP Address: Shows the current IP address of the device. MAC Address: Shows the device MAC Address. Protocol version: Shows the version of the Utility protocol.
50-Port Dual Web Rack Switch In order to receive Trap information, switch has to be configured with Trap IP and Trap Events in Web browser, which are available in the Trap Setting Menu Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you want to monitor. Delete Item: To delete the device in the Monitor List. Device Setting You can set the device by using the function key in the Device Setting Dialog box.
50-Port Dual Web Rack Switch Do NOT upgrade firmware on any Atlantis Land product over a wireless connection. Failure of the device may result. Use only hard-wired network connections. Web Access: Double click the device in the Monitor List or select a device in the Monitor List and press this “Web Access” button to access the device in Web browser. Toolbar The toolbar in the Web Management Utility have four main tabs : File, View, Options and Help.
50-Port Dual Web Rack Switch Chapter 4 WEB Configuration The 48+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch has a Web GUI interface for smart switch configuration. The Switch can be configured through the Web Browser. A network administrator can manage, control and monitor the switch from the local LAN.
50-Port Dual Web Rack Switch 4.2 Setup Menu When the main page appears, find the Setup menu in the left side of the screen. Click on the setup item that you want to configure. There are 3 options: Port Settings, VLAN Settings, Trunk Setting. Port Settings In Port Settings menu, this page will show each port’s status, press the ID parameter to set each port’s Speed, Flow Control, and QoS priority. When you need to renew the posted information, press the “Refresh” button.
50-Port Dual Web Rack Switch To change the port setting, click on the ID parameter to enter to the selected port to configure its Speed/Disable, Flow control and QoS setting. Speed/Disable: This setting has six modes: 100M Full, 100M Half, 10M Full, 10M Half, Auto and Disable. Flow Control: This setting determines whether or not the Switch will be handling flow control. Set FlowCtrl to Enable for avoiding data transfer overflow.
50-Port Dual Web Rack Switch QoS: In some ports that need to have a high priority to manage the data transfer, QoS should be change. Set the port’s QoS to high to determine the port will always transfer their data first. QoS function can be working in any port either from port 1 to port 24 or from port 25 to port 52.However, QoS setting can not be working in different port group. For example, we set port 7 and port 28 priority high. When we send packet to port 28, port 7's QoS doesn't work.
50-Port Dual Web Rack Switch Once you want to modify the VLAN Group, check on the ID parameter, the ID VLAN configuration window will pop out. Group 1 and Group 2 can not be managed at the same time When add a new Vlan, the members of default Vlan 1 are removed automatically. Therefore, packets can only transmit among the member ports of new Vlan. Packets can not fordward among the ports which are not included in the new vlan.
50-Port Dual Web Rack Switch 4.3 Maintenence Status Click on the “Status” to present the device status on this screen, it will show the System Status, Port Status, VLAN Status and Trunk Status . Press “Refresh” when you need to renew the posted information. Statistics The Statistic Menu screen will show the status of each port packet count. For Detail packet information, click on the ID parameter as Figure.
50-Port Dual Web Rack Switch System Settings The System Setting includes the System name, Location name, Login Timeout, IP Address, Subnet Mask and Gateway. Through the Web Management Utility, you can easily recognize the device by using the System Name and the Location Name. The Login Timeout is to set the idle time-out for security issue, when there is no action when running the Web Smart Utility and the time is up, you must re-login to Web Smart Utility before you set the Utility.
50-Port Dual Web Rack Switch TRAP The Trap Setting enables the device to monitor the Trap through the Web Management Utility, set the Trap IP Address of the manager where the trap to be sent. System Events: Monitoring the system’s trap. • Device Bootup: a trap when booting up the system. • Illegal Login: a trap when there is using a wrong password login, and it will record from where the IP to be login. Fiber Port Events: Monitoring the Fiber port status.
• • 50-Port Dual Web Rack Switch Abnormal* Transmit Error: a trap when there are transmit data error in copper port. Abnormal*: 50 error packet count within 10 seconds. Abnormal*: 50 error packet count within 10 seconds. Set Password Password is the invaluable tool for the manager to secure Web Management Switch, use this function to change the password. If you forget the password, press the “Reset” button in the rear panel of the Switch, the current setting includes VLAN, Port Setting… etc.
50-Port Dual Web Rack Switch Reset Settings The Factory Reset button helps you to reset the device back to the default setting from the factory. Be aware that the entire configuration will be reset, the IP address of the device will be set to default setting 192.168.0.1 [password=admin]. Logout When press this function, the web configuration will go back to first Login page.
50-Port Dual Web Rack Switch APPENDIX A RJ-45 Pin Specification The following diagram and tables show the standard RJ-45 receptacle/connector and their pin RJ-45 Connector pin assignment Contact Media Direct Interface Signal 1 TX + (tx) 2 TX - (tx) 3 Rx + (rx) 4 Not used 5 Not used 6 Rx - (rx) 7 Not used 8 Not used The standard cable, RJ-45 pin assignment. The standard RJ-45 receptacle/connector.
50-Port Dual Web Rack Switch APPENDIX B Technical Specifications Standard IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3z 1000BASE-SX/LX Gigabit Ethernet Protocol Data Transfer Rate Topology IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3x Full Duplex Flow Control CSMA/CD Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half duplex), 200Mbps (full-duplex) Gigabit Ethernet: 2000Mbps (full-duplex) Star 10BASET: 2-pair UTP Cat.
50-Port Dual Web Rack Switch APPENDIX C Support If you have any problems with theSwitch , please consult this manual. If you continue to have problems you should contact the dealer where you bought this Switch. If you have any other questions you can contact the Atlantis Land company directly at the following address: Atlantis Land SpA Viale De Gasperi, 122 20017 Mazzo di Rho(MI) Tel: +39. 02.93907634(help desk) / +39. 02.93906085, Fax: +39. 02.93906161 Email: info@atlantis-land.
