I-Storm USB ADSL modem A01-AU1 Manual for Linux and Mac OS 9/X A01-AU1_ME01
I-Storm USB ADSL modem SOMMARIO Chapter 1 .............................................................................1 1.1 I-Storm USB ADSL Modem Features ......................1 1.2 Package Contents.......................................................1 1.3 The Front LEDs.........................................................2 1.4 Information from ISP ................................................2 Chapter 2 .............................................................................4 2.
4.2.4 Configuration – DNS Configuration ................44 4.2.5 System – Password Configuration....................45 4.2.6 System – Diagnostic Test .................................45 4.2.7 System – System Log .......................................50 4.2.8 Advance – WAN Status....................................51 4.2.9 Advance – ATM Status ....................................51 4.2.10 Advance – TCP Status....................................52 4.2.11 Advance – ADSL Configuration ....................53 4.
I-Storm USB ADSL modem Chapter 1 Introduction 1.1 I-Storm USB ADSL Modem Features I-Storm USB ADSL Modem provides the following features: ♦ Bus-powered USB modem for broadband ADSL. ♦ Downstream data rate up to 8 Mbps and upstream up to 1 Mbps. ♦ No external power supply is required. ♦ Hot Plug and Play for Microsoft Windows 98 (SE), 2000, Me, and XP. ♦ Mac OS 9/X and Linux (Red Hat) ♦ Supports NDIS interface for RAS and Dial-Up Networking. ♦ Software upgradeable.
I-Storm USB ADSL modem 3. 4. 5. One RJ-11 ADSL telephone cable One USB cable One Quick Start Guide 1.3 The Front LEDs LED Meaning USB When this LED is lit, it indicates that the USB port is connected to the PC and working properly. DATA Flashes when transferring data. ADSL When lit, it indicates that the ADSL (Line) port is connected to the DSLAM and working properly. 1.
I-Storm USB ADSL modem PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS) IP address (it can be automatically assigned from ISP or be set fixed). PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and Domain Name System (DNS) IP address (it can be automatically assigned from ISP or be set fixed).
I-Storm USB ADSL modem Chapter 2 Installation 2.1 Installing I-Storm USB ADSL Modem Please refer to the following instructions: 1. Connect ADSL telephone cable to the LINE RJ-11 jack. 2. Connect the USB cable to the USB port and connect the other end to the PC. 2.2 Installing I-Storm USB ADSL Modem Drivers 2.2.1 For Windows 98 1. Start Windows. After the opening banner, Windows will tell you that the new device has been detected. You will then see the following screen. Click “Next >”.
I-Storm USB ADSL modem 2. In the next window, select “Search for the best driver for your device” and click “Next >”. 3. Insert the installation CD into the CD-ROM drive and check “Specify a location”.
I-Storm USB ADSL modem ADSL WAN Adapter. (Please refer Information from ISP section for more details.) Click “OK” and then “Next>” to continue.
I-Storm USB ADSL modem 4. 5. Continuing through the Wizard, click the “Next >” button. Windows will start copying files to your system. Then, click “Finish”. You will see the following screen prompting for the path of the Windows source files. Please specify a location. Click “OK”.
I-Storm USB ADSL modem 6. I-Storm USB ADSL Modem driver is successfully installed and the Status Task Bar will appear in the System Tray. 7. I-Storm USB ADSL Modem icon is installed in the Control Panel. 8. Go to the Device Manager, the “I-Storm USB ADSL LAN Adapter” is under the Network Adapters, and “IStorm USB ADSL Modem” is under the Universal Serial Bus Controllers for I-Storm USB ADSL LAN driver installation.
I-Storm USB ADSL modem 2. Insert the installation CD into the CD-ROM drive and check “Specify a location”. Click “Browse…” to specify the driver directory such as CDRom:\Driver\LAN for installing I-Storm USB ADSL LAN Adapter or CDRom :\Driver\WAN for installing I-Storm USB ADSL WAN Adapter. (Please refer Information from ISP section for more details.) Click “OK” and then “Next>” to continue.
I-Storm USB ADSL modem 3. Continuing through the Wizard, Windows will start copying files to your system. Then, click “Finish”. 4. I-Storm USBADSL Modem driver is successfully installed and the Status Task Bar will appear in the System Tray. 5. I-Storm USB ADSL Modem icon is installed in the Control Panel.
I-Storm USB ADSL modem 6. Go to the Device Manager, the “I-Storm USB ADSL LAN Adapter” is under the Network Adapters, and “I-Storm USB ADSL Modem” is under the Universal Serial Bus Controllers for I-Storm USB ADSL LAN driver installation. Go to the Device Manager, the “I-Storm USB ADSL WAN Adapter” is under the Network Adapters, and “IStorm USB ADSL Modem” is under the Universal Serial Bus Controllers for I-Storm USB ADSL WAN driver installation. 2.2.3 For Windows 2000 1. Start Windows.
I-Storm USB ADSL modem ROM drive. In next window, check “Specify a location” and click “Next>”. 3. Click “Browse…”. In the Locate File window, specify the driver directory such as CDRom:\Driver\LAN\CxtCAFEU for installing I-Storm USB ADSL LAN Adapter or CDRom:\Driver\WAN\CxtCAFEU for installing I-Storm USB ADSL WAN Adapter. (Please refer Information from ISP section for more details.) Click “Open” and then “Next>“ to continue.
I-Storm USB ADSL modem 4. When windows titled “Digital Signature Not Found” appear, press “Yes” to continue the installation. 5. Press “Finish”. 6. I-Storm USB ADSL Modem driver is successfully installed and the Status Task Bar will appear in the System Tray.
I-Storm USB ADSL modem 7. I-Storm USB ADSL Modem icon is installed in the Control Panel. 8. Go to the Device Manager, the “I-Storm USB ADSL LAN Adapter” is under the Network Adapters, and “IStorm USB ADSL Modem” is under the Universal Serial Bus Controllers for I-Storm USB ADSL LAN driver installation.
I-Storm USB ADSL modem 2. Insert the installation CD into the CD-ROM drive and select “Include this location in the search”. Click “Browse” to specify the driver directory such as CDRom:\Driver\LAN for installing I-Storm USB ADSL LAN Adapter or CDRom:\Driver\WAN for installing I-Storm USB ADSL WAN Adapter. (Please refer Information from ISP section for more details.) Click “OK” and then “Next>” to continue.
I-Storm USB ADSL modem 16
I-Storm USB ADSL modem 3. When windows titled “Hardware Installation” or “Software Installation” appear, press “Continue Anyway” to go on. 4. Then, click “Finish”.
I-Storm USB ADSL modem 5. Wait a few moments. Windows will show that the new device, I-Storm USB ADSL LAN (or WAN) Adapter, has been detected. Select “Install from a list or specific location”. Click “Next >” 6. Click “Next >” when the following figure appears. 7. When windows titled “Hardware Installation” appears, press “Continue Anyway”.
I-Storm USB ADSL modem 8. Then, click “Finish” to end the installation. 9. I-Storm USB ADSL Modem driver is successfully installed and the Status Task Bar will appear in the System Tray. 10. I-Storm USB ADSL Modem icon is installed in the Control Panel. 11. Go to the Device Manager, the “I-Storm USB ADSL LAN Adapter” is under the Network Adapters, and “IStorm USB ADSL Modem” is under the Universal Serial Bus Controllers for I-Storm USB ADSL LAN driver installation.
I-Storm USB ADSL modem “I-Storm USB ADSL Modem” is under the Universal Serial Bus Controllers for I-Storm USB ADSL WAN driver installation. 2.2.5 For Mac OS 9 If you connect the ADSL Modem/Router through USB port, for the first time the USB cable is connected to the PC, the host PC OS will automatically detect the device. Follow the steps to install the USB driver. 1. When PC tells you that the new device has been detected, insert the installation CD into the CD-ROM drive (CDRom:\Driver\MacOS9).
I-Storm USB ADSL modem 2.2.6 For Mac OS X 1. Insert the installation CD into the CD-ROM drive, click the driver installer. 2. Input the user name and password of your Mac system. 3. Click “Continue”.
I-Storm USB ADSL modem 4. Select a destination to install the driver, choose Mac X. 5. Click “Continue”.
I-Storm USB ADSL modem 6. Click “Continue Installation” to end the installation. 2.2.7 For Linux Redhat 7.1/7.2 1. Install the driver (Redhat 7.
I-Storm USB ADSL modem 2. 3. #rpm –i USB-RED-HAT-7.1.i386.rpm (Redhat 7.2) #rpm –i USB-RED-HAT-7.2.i386.rpm (Redhat 8.0) #rpm –i USB-RED-HAT-8.0.i386.rpm (Redhat 9.0) #rpm –i USB-RED-HAT-9.0.i386.rpm Launch the driver #cd /usr/local/e2 #insmod e2.o #ifconfig hsb0 up(Note: run this command after the READY LED blinks) #dhcpcd hsb0 (Note: run this command after the READY LED blinks) Uninstall the driver #rpm –e USBENDPOINT After your installation, please edit this file /etc/rc.d/rc.
I-Storm USB ADSL modem Chapter 3 Configuration Windows Follow the instructions below to configure your I-Storm USB ADSL Modem. 1. Click I-Storm USB ADSL Modem icon in the Control Panel or ADSL Configuration icon on the desktop. The status of ADSL connection will be displayed.
I-Storm USB ADSL modem 2. Press [Alt]+[P] on keyboard, the following figure appears.
I-Storm USB ADSL modem 3. Select the Protocol Setup tag, please set the value of “VPI”, “VCI” and “Encapsulation Mode”. Then, click “OK”. For BT (VPI=0, VCI=38), for KC(VPI=1, VCI=50).
I-Storm USB ADSL modem 3.1 I-Storm USB LAN(RFC1483, RFC1577) ADSL 3.1.1 For Windows 98 / Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP → I-Storm USB ADSL LAN Adapter. Then, click Properties. 3. Select the IP Address tab. In this page, click the Specify an IP address radio button and enter the “IP address” and “Subnet Mask” provided by your ISP.
I-Storm USB ADSL modem 4. Select the Gateway tab. Enter the “gateway” provided by your ISP and click Add.
I-Storm USB ADSL modem 5. In the DNS Configuration page. Click the Enable DNS radio button. Enter the “Host” name and “DNS Server IP address” provided by your ISP. Then, press the Add button.
I-Storm USB ADSL modem 3.1.2 For Windows 2000 / XP 6. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 7. Right–click on Local Area Connection that is using the I-Storm USBA DSL LAN Adapter and then click “Properties”.
I-Storm USB ADSL modem 8. Select Internet Protocol (TCP/IP). Then, click “Properties”. 9. Select Use the following IP address, and then enter the “IP address”, “Subnet mask”, and “Default gateway” provided by your ISP. Select Use the following DNS server addresses and then enter the provided DNS server IP address.
I-Storm USB ADSL modem 3.2 I-Storm USB WAN(PPPoA, PPPoE) 1. ADSL Click ADSL Easy Dialup icon on the desktop. Then, the following window appears. Enter the “Username” and “Password” provided by your ISP. Let the Phone number field be blank.
I-Storm USB ADSL modem 2.
I-Storm USB ADSL modem Chapiter 4 Mac OS9,X and Linux The ADSL USB Modem can be configured with your web browser, the default IP address of the ADSL USB Modem is 192.168.1.254 and subnet mask is 255.255.255.0. The ADSL USB Modem uses “Emulate USB port to Ethernet” technology to emulate the USB port to Ethernet port, the terminology “LAN” described in the paragraph below is equal to “USB”. Any TCP/IP capable workstation can be used to communicate with or through the ADSL Modem/Router.
I-Storm USB ADSL modem 4.1 Factory Default Settings Before you configure this device, you need to know the following default settings. 1. Web Configurator Administrator User Name Password admin password 2. Device IP Network settings in LAN site IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 3.
I-Storm USB ADSL modem 4.2 Configuring with Web Browser The ADSL USB Modem can be configured with your Web browser. Open the web browser, enter the local port IP address of the ADSL Router, which default at 192.168.1.254, and click “Go” to get the login page. The default user name and password are admin and password.
I-Storm USB ADSL modem Then, click “OK” to log in. You can modify the passwords for security and management purpose. At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page. Click on the desired item to expand the page in the main navigation pane. 4.2.
I-Storm USB ADSL modem Status – PPP Displays the status PPP for each PPP interface.
I-Storm USB ADSL modem 4.2.2 Configuration – WAN Configuration The screens below contain settings for the WAN interface toward Internet. • VPI: Consult the telephone company to get the Virtual Path Identifier (VPI) number. The default value is 0. • VCI: Consult the telephone company to get the Virtual Channel Identifier (VCI) number. The default value is 32. • Static IP Address: Enter the information provided by your ISP. • Subnet Mask: Enter the information provided by your ISP.
I-Storm USB ADSL modem ENCAPSULATION There are eleven ways ─ PPPoE VC-Mux, PPPoE LLC, PPPoE None, PPPoA VC-Mux, PPPoA LLC, 1483 Bridged IP VC-Mux, 1483 Bridged IP LLC, 1483 Routed IP VC-Mux, 1483 Routed IP LLC, Classical IP over ATM, Native ATM ─ for the device to have a public IP address and then to access Internet. You have to check with your ISP about which way is adopted. PPP If your encapsulation is set to be PPPoE or PPPoA, the following fields must be entered.
I-Storm USB ADSL modem • Automatic Reconnect: Check to enable this device to automatically re-establish the PPPoE session when disconnected by ISP. • PPP connect on WAN access: Check to enable this device to automatically re-establish the PPPoE session whenever there is WAN access traffic, e.g. Internet access. DHCP • DHCP client enable: Check to enable the DHCP client function if you want the device to get an IP address automatically from your ISP. • Host Name: Enter the name of your work group.
I-Storm USB ADSL modem • IP Address: Default at 192.168.1.254. This is the device IP address in LAN site. If you plan to change it to another IP address to a different range of IP subnet. Please make sure your PC is also located at the same IP subnet. Otherwise, you may not be able to access the ADSL Router. • Subnet Mask: Default at 255.255.255.0.
I-Storm USB ADSL modem 4.2.4 Configuration – DNS Configuration A Domain Name System (DNS) contains a mapping table for domain name and IP address. In the Internet, every host has a unique and friendly name such as www.yahoo.com and IP address. The IP address is so hard to remember that you may just enter the friendly name www.yahoo.com and then the DNS will convert it to its equivalent IP address. You can obtain Domain Name System (DNS) IP address automatically if ISP provides it when you logon.
I-Storm USB ADSL modem 4.2.5 System – Password Configuration In factory setting, the default password for administrator is password, and that for user is also password. You can change the default password to ensure that someone cannot adjust your settings without your permission. Every time you change your password, please record the password and keep it at a safe place. Please note that the minimum input for password is 8 alphanumeric characters long.
I-Storm USB ADSL modem Checking LAN Connection Testing Ethernet LAN connection This test passes if the Ethernet LAN interface is working properly.
I-Storm USB ADSL modem This test checks your DSL modem to see if it can successfully negotiate and establish a DSL connection with your service provider's central office equipments. The test returns PASS if a DSL connection is established. If this test returns FAIL, please try the test again a few minutes after this test is completed. Since your DSL modem need a couple of seconds to a few minutes to establish the DSL connection depending on your phone line quality.
I-Storm USB ADSL modem If this test return FAIL consistently and your DSL modem seems not working, check to make sure the VPI and VCI are configured correctly. This test returns SKIPPED if the DSL synchronization test failed. Test Ethernet connect to ATM This test returns PASS if the ATM AAL5 module is loaded correctly in your DSL modem. If this test returns FAIL, an internal error has occurred. This test returns SKIPPED if the DSL synchronization does not return PASS.
I-Storm USB ADSL modem If this test returns FAIL, run this test again a few minutes after this test is completed. If this test returns FAIL consistently and DHCP client is turned on in your DSL modem, check with your service provider. If this test returns FAIL consistently and your DSL modem is statically assigned an IP address, make sure the IP address is the correct one assigned by your service provider. This test returns SKIPPED if “Ethernet connect to AAL5” test does not return PASS.
I-Storm USB ADSL modem This test returns SKIPPED if "IP connect to PPP" or "IP connect to Ethernet" test does not return PASS. 4.2.7 System – System Log Display the system logs cumulated till the present time. You can trace the historical information through this function. It refreshes every five seconds.
I-Storm USB ADSL modem 4.2.8 Advance – WAN Status Each VC setting you enabled in the WAN Configuration section except that uses the PPP encapsulation will be displayed in this table. 4.2.9 Advance – ATM Status Display the status of ATM.
I-Storm USB ADSL modem 4.2.10 Advance – TCP Status Display the status of TCP. This screen will automatically refresh every two seconds.
I-Storm USB ADSL modem 4.2.11 Advance – ADSL Configuration • Trellis: Default at Enabled. • Handshake Protocol: Default at Autosense – G.dmt first. You can also choose other protocols, such as Autosense – T1.413 first, G.dmt/G.lite, T1.413, G.dmt, G.lite. • Wiring Selection: Default at Tip/Ring. Select Auto or A/A1 if necessary.
I-Storm USB ADSL modem 4.2.12 Save Settings Click the Submit button to write settings to flash. Then, the system will reboot for changes to take effect.
I-Storm USB ADSL modem 55
I-Storm USB ADSL modem APPENDIX Product Support If you have any problems with the I-Storm USB ADSL Modem, please contact the dealer where you bought this product. If you have any other questions you can contact the Atlantis Land company directly at the following address: Atlantis Land SpA Viale De Gasperi 122 20017 Mazzo di Rho (MI) Tel: +39.(0)2.93906085 Fax: +39.(0)2.93906161 Help Desk :+39.(0)2.93907634 Email: tecnici@atlantis-land.com WWW: www.atlantis-land.
I-Storm USB ADSL modem 57
