WebShare RB300 Wireless N Broadband Router A02-RB-W300N USER GUIDE A02-RB-W300N _ME01 Where solutions begin ISO 9001:2000 Company certified
WebShare RB300 INDEX CHAPTER 1: INTRODUCTION 1.1 An Overview of the WebShare RB300 1.2 Package Contents 1.3 Technical Features 1.4 System Requirements 1.5 Setup CHAPTER 2: USING WIRELESS BROADBAND ROUTER 2.1 Cautions for using the Wireless Broadband Router 2.2 The Front LEDs 2.3 The Rear Ports 2.4 Cabling CHAPTER 3: CONFIGURATION 3.1 Before Configuration 3.1.1 Windows 95/98/ME 3.1.2 Windows NT4.0 3.1.3 Windows 2000 3.1.4 Windows XP 3.2 Factory Default Settings 3.2.1 Password 3.2.2 LAN and WLAN Ports 3.
WebShare RB300 3.7.1 Filter 3.7.2 Virtual Server 3.7.3 Special AP 3.7.4 DMZ 3.7.5 Firewall Settings 3.8 System 3.8.1 Password 3.8.2 Time 3.8.3 Device Information 3.8.4 Log 3.8.5 Log Settings 3.8.6 Statistics 3.8.7 Restart 3.8.8 Firmware 3.8.9 Configuration 3.8.10 UPnP 3.8.11 Ping Test 3.8.12 Remote Management APPENDIX A: TROUBLESHOOTING A.1 LEDs A.1.1 LED Power A.1.2 LED LAN A.1.3 LED WLAN A.2 WEB A.3 Login A.4 Remote Management A.
WebShare RB300 Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp. Pentium is trademark of Intel. All copyright reserved. The Atlantis Land logo is a registered trademark of Atlantis Land SpA.
WebShare RB300 CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. CE in which Countries where the product may be used freely: Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland. France: except the channel 10 through 13, law prohibits the use of other channels.
WebShare RB300 CHAPTER 1: Introduction Congratulations on your purchase of Atlantis Land Wireless Broadband Router. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing and office resources sharing, and it is easy to configure and operate for every users. This manual discusses how to install the Webshare RB300. 1.
WebShare RB300 1.3 Technical Features WebShare RB300 provides the following features: Compliant with 802.11n (draft), IEEE 802.11g and 802.
WebShare RB300 Make sure that there is proper heat dissipation from and adequate ventilation around the Broadband Router. Do not place heavy objects on the Broadband Router. Fix the direction of the antennas. Try to place the Wireless Router in a position that can best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be. The antenna’s position enhances the receivingsensitivity. CHAPTER 2: Using Wireless Broadband Router 2.
WebShare RB300 2.2 The Front LEDs LED POWER STATUS MEANING This indicator lights green when the hub is receives power, otherwise it is off. This indicator blinks green means the Internet Broadband Router is working successful. Otherwise, this indicator always on or off means the function of the Internet Broadband Router is fail. WAN The indicators light green when the WAN port was connected to an xDSL/Cable modem successfully.
WebShare RB300 2.3 The Rear Ports PORT POWER JACK WAN LAN REVERSE SMA RESET USAGE Plug the power adapter to this power jack In the four port broadband router, there is an RJ-45 10/100Mbps Auto-MDIX port for the WAN that will fit the xDSL/Cable modem’s specification need. Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections. There are one 2 dBi Gain Antenna in the rear panel for wireless connection.
WebShare RB300 Plug in the other end of the network cable to the Ethernet port of the xDSL or Cable modem (E.G A02-RA141 or A02-RA111). Use another network cable to connect to the Ethernet card on the computer system; the other end of the cable connects to the LAN port of the Internet Broadband Router. Since the Wireless Broadband Router has four ports, you can connect up to four computers directly to the unit.
WebShare RB300 CHAPTER 3: Configuration The Wireless Broadband Router has a Web GUI interface for the configuration. The device can be configured through the Web Browser. A network manager can manage, control and monitor the Router from the local LAN. This section indicates how to configure the AP to enable its functions. 3.
WebShare RB300 3.1.1 Windows 95/98/ME 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties. 4. Pag. 8 Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button.
WebShare RB300 3.1.2 Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, doubleclick on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK. Pag.
WebShare RB300 3.1.3 Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties. 4. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons.). 5. Click OK to finish the configuration. Pag.
WebShare RB300 3.1.4 Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, doubleclick on Network Connections. 2. Double-click Local Area Connection 3. In the LAN Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons 6. Click OK to finish the configuration. Pag.
WebShare RB300 3.2 Factory Default Settings Before configuring the Wireless Broadband Router through WLAN, make sure that the SSID, Channel and the WEP was set properly. The default setting of the Wireless Broadband Router that you will use: User: admin Password: admin IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: enable (192.168.1.100-192.168.1.199) Wep Encryption: disable SSSID: N Router Channel: 6 3.2.
WebShare RB300 3.3 Accessing the Wireless Broadband Router Web Configurator Before you configure this device, note that when the Wireless Broadband Router is configured through an Ethernet connection, make sure the manager PC must be set on same the IP network. Open Internet Explorer 5.0 or above Web browser. Enter IP address http://192.168.1.1 (the factory-default IP address setting) to the address location.
WebShare RB300 3.3.1 Setup Wizard Setup wizard is provided as the part of the web configuration utility. User can simply follow the step-by-step process to get the wireless router configuration ready to run in 6 easy steps by clicking on the “Wizard” button on the function menu. The following screen will appear. Please click Next to continue. Pag.
WebShare RB300 Step 1: Setup New Password User can change the password and then click Next to continue. Please click Next to continue. Pag.
WebShare RB300 Step2: Choose time zone Select the time zone from the drop down list. Please click Next to continue. Pag.
WebShare RB300 Step 3: Set LAN and DHCP Server Set user’s IP address and mask. The default IP is 192.168.1.1. If user likes to enable DHCP, please click Enabled. DHCP enabled is able to automatically assign IP addresses. Please assign the range of IP addresses in the fields of Range start and Range end. Please click Next to continue. Please click Next to continue. Pag.
WebShare RB300 Step 4: Set Internet connection If the Wireless Broadband Router is unable to auto detect your Internet connection, you will need to manually select the Internet connection type: Obtain IP automatically, Fixed IP, PPPoE, PPTP, L2TP or BigPond. Please click Next to continue. Pag.
WebShare RB300 Set Dynamic IP Address: If user has enabled DHCP server, choose Obtain IP automatically (DHCP client) to have the router assign IP addresses automatically. If your ISP requires you to enter a specific host name or MAC address, please enter it in . Please click Next to continue. Pag.
WebShare RB300 Set Fixed IP Address: If the Internet Service Providers assign a fixed IP address, choose this option and enter the assigned IP address, subnet mask, gateway IP and DNS IP addresses for your Broadband Router. Please click Next to continue. Pag.
WebShare RB300 Set PPPoE Client: Obtain IP Automatically: If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password and User Name, and then the ISP uses PPPoE. Choose this option and enter the required information. Please click Next to continue. Pag.
WebShare RB300 Specify IP: If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password, User Name and a Fixed IP Address, choose this option and enter the required information. Please click Next to continue. Pag.
WebShare RB300 Set PPTP/L2TP Client: If connected to the Internet using a (PPTP/L2TP) xDSL Modem, enter the your IP Address, Subnet Mask, Gateway, Server IP, PPTP/L2TP Account and PPTP/L2TP Password, Your Subnet Mask required by your ISP in the appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field, otherwise, leave it to zero. Please click Next to continue. Pag.
WebShare RB300 Step 5: Set Wireless LAN connection Click Enable to enable wireless LAN. If user enables the wireless LAN, type the SSID in the text box and select a communications channel. The SSID and channel must be the same as wireless devices attempting communication to the router. Please click Next to continue. Pag.
WebShare RB300 Step 6: Restart The Setup wizard is now completed. The new settings will be effective after the Wireless router restarted. Please click Restart to reboot the router. If user does not want to make any changes, please click Exit to quit without any changes. Pag.
WebShare RB300 3.3.2 Navigating the Broadband Router Web Configurator The screen will show the status of the Wireless Broadband Router when you login to the device. There are six main functions included in the left side of the main screen: WAN Wireless LAN Access Control System Wizard Pag.
WebShare RB300 3.4 WAN This function enables users to set up the Wireless Broadband Router WAN connection, specify the IP address for the WAN, add DNS numbers, and enter the MAC address. 3.4.1 Connection Type Connection Type: Select the connection type, either DHCP client, Fixed IP or PPPoE, PPTP, L2TP or BigPond from the drop-down list. Pag.
WebShare RB300 DHCP CLIENT OR FIXED IP If user has enabled DHCP server, choose Obtain IP automatically (DHCP client) to have the router assign IP addresses automatically. WAN IP Address: Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Specify IP is selected, type the IP address, subnet mask, and default gateway in the text boxes. User’s ISP will provide with this information.
WebShare RB300 Gateway: For the Specify mode, enter the specific gateway IP address that provided by your ISP. DNS 1/2: Manually specific DNS server IP address. For the Obtain IP Automatically mode, leave 0.0.0.0 hear, the DHCP server will provides DNS server automatically. Clone MAC Address: If your ISP requires you to enter a specific MAC address, please enter it in. The Clone MAC Address button is used to copy the MAC address of your Ethernet adapter to the Router. Click Apply to save. Pag.
WebShare RB300 PPPoE Choose Obtain IP Automatically if connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password and User Name, and then the ISP uses PPPoE. Choose this option and enter the required information. Choose Specify IP if connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password, User Name and a Specify IP Address, choose this option and enter the required information. Click Apply to save. Pag.
WebShare RB300 PPTP/L2TP Choose Obtain IP Automatically if connected to the Internet using a PPTP/L2TP (Dial-up xDSL) connection, enter the your Server IP, PPTP/L2TP Account and PPTP/L2TP Password, if your ISP has provided you with a DNS IP address, enter it in the DNS field, otherwise, leave it zero.
WebShare RB300 3.4.2 Dynamic DNS This synchronizes the DDNS server with your current Public IP address when you are online. First, you need to register your preferred DNS with the DDNS provider. Then, please selected one of DDNS server than fill the related information in the below fields: Host Name, User Name and Password. To use DDNS client, you have to register a DDNS Account. . Click Apply to save. Pag.
WebShare RB300 3.5 Wireless This section enables user to set wireless communications parameters for the router's wireless LAN feature. 3.5.1 Basic This page allow user to enable and disable the wireless LAN function, create a SSID, and select the channel for wireless communications. Wireless: Enables or disables the wireless LAN function of the Wireless Broadband Router. SSID: Type an SSID in the text box.
WebShare RB300 Channel Width: Select the Channel Width: Auto 20/40: This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz: Select if you are not using any 802.11n wireless clients. SSID Broadcast: While SSID Broadcast is enabled, all wireless clients will be able to view the Wireless Broadband Router’s SSID. For security purposes, users may want to disable SSID Broadcast to ensure only authorized clients have access. Click Apply to save.
WebShare RB300 3.5.2 Security This function enables user to set authentication type for secure wireless communications. Open System allows public access to the router via wireless communications. Shared Key requires the user to set a WEP key to exchange data with other wireless clients that have the same WEP key. This router also supports WPA, WPA2 and WPA-PSK, WPA2-PSK.. Security: Enable or Disable the wireless LAN security. Pag.
WebShare RB300 WEP WEP: Open System and Shared Key requires the user to set a WEP key to exchange data with other wireless clients that have the same WEP key. WEP Key Format: Select the key format from the drop-down list HEX or ASCII. WEP Key Length: Select the level of encryption from the drop-down list. The Wireless Broadband Router supports, 64 and 128-bit encryption. WEP Key 1 ~ 4: Enables users to create up to 4 different WEP keys. Manually enter a set of values for each key.
WebShare RB300 WPA/WPA2 If WPA or WPA2 PSK is selected, the above screen is shown. Encryption Type: Select the encryption type for TKIP or AES encryption. Passphrase: The length should be 8 characters at least. If WPA or WPA2 EAP is selected, please set the length of the encryption key and the parameters for the RADIUS server. Encryption Type: Select the encryption type for TKIP or AES encryption.
WebShare RB300 3.5.3 Advanced This function enables user to configure advanced wireless functions. Beacon Interval: Type the beacon interval in the text box. User can specify a value from 20 to 1000. The default beacon interval is 100. RTS Threshold: Type the RTS (Request-To-Send) threshold in the text box. This value stabilizes data flow. If data flow is irregular, choose values between 256 and 2346 until data flow is normalized. Fragmentation Threshold: Type the fragmentation threshold in the text box.
WebShare RB300 3.5.4 WiFi Protected Setup This screen enables users to configure the Wi-Fi Protected Setup function. WPS: Enable or Disable the WPS (Wi-Fi Protected Setup) function Status: Display the state (Unconfigured/Configured State) information of WPS. Self-PIN Number: Display the default PIN number of WLAN Router. Client PIN Number: Type Client PIN number the client uses to negotiate with WLAN Router via WPS protocol. It is only used when users want their station to join Router's network.
WebShare RB300 3.6 LAN The function enables user to configure the LAN port IP address & DHCP Server. 3.6.1 Basic This page leads to set LAN port properties, such as the host name, IP address, and subnet mask. Host Name: Type the host name in the text box. The host name is required by some ISPs. The default host name is "Wireless Router" IP Address: This is the IP address of the router. The default IP address is 192.168.1.1. Subnet Mask: Type the subnet mask for the router in the text box.
WebShare RB300 3.6.2 DHCP DHCP Server: Enables the DHCP server to allow the router to automatically assign IP addresses to devices connecting to the LAN. DHCP is enabled by default. DHCP Server Start IP: Type an IP address to serve as the start of the IP range that DHCP will use to assign IP addresses to all LAN devices connected to the router. Pag.
WebShare RB300 DHCP Server End IP: Type an IP address to serve as the end of the IP range that DHCP will use to assign IP addresses to all LAN devices connected to the router. Lease Time: The lease time specifies the amount of connection time a network user be allowed with their current dynamic IP address. Add Static DHCP: Selected Enable the Static DHCP allows you to assign a static IP address to the PC that has the IP address and MAC address mapping set in the Static DHCP List.
WebShare RB300 3.7 Access Control This access control enables you to define access restrictions, set up protocol and IP filters, create virtual servers, define access for special applications such as games, and set firewall rules. 3.7.1 Filter Using filter to deny or allow the users to access. Five types of filters to select: MAC, IP Filter, URL blocking, Domain blocking and Protocol filter. MAC FILTER Pag.
WebShare RB300 MAC Filter: Enables you to allow or deny Internet access to users within the LAN based upon the MAC address of their network interface. Click the radio button next to Disabled to disable the MAC filter. Disable: Disable the MAC filter function. Allow: Only allow computers with MAC address listed in the MAC Table. Deny: Computers in the MAC Table are denied Internet access. MAC Table: Use this section to create a user profile which Internet access is denied or allowed.
WebShare RB300 DOMAIN/URL BLOCKING You could enable Domain/URL blocking to deny the users from accessing the specified Domain/URL. Add those specified Domain/URL in the text box. Disable: Disable the Domain/URL Blocking function. Allow: Allow users to access all domains except “Blocking Domains/URL”. Deny: Deny users to access all domains except “Permitted Domains/URL”. Blocked/Permitted Domains/URL: List domains you will Blocked or Permitted.
WebShare RB300 Delete: Select a Domain/URL from the table at the bottom of the list and click Delete to remove the Domain/URL. Add: Click to Add button to add domain to the Domains list. Cancel: Click the Cancel button to erase all fields and enter new information. Click Apply to save. PROTOCOL/IP FILTERS This protocol filter enables you to allow and deny access based upon a communications protocol list you create. The protocol filter profiles are listed in the table at the bottom of the page. Pag.
WebShare RB300 Enable: Click to enable or disable the IP address filter. Name: Type the name of the user to be denied access. Protocol: Select a protocol (TCP or UDP) to use for the virtual server. Port: Type the port range of the protocol. IP Range: Type the IP range. IP addresses falling between this value and the Range End are not allowed to access the Internet. Add: Click to add the IP range to the table at the bottom of the screen.
WebShare RB300 3.7.2 Virtual Server This screen enables users to create a virtual server via the WLAN Router. If the WLAN Router is set as a virtual server, remote users requesting Web or FTP services through the WAN are directed to local servers in the LAN. The WLAN Router redirects the request via the protocol and port numbers to the correct LAN server. The Virtual Sever profiles are listed in the table at the bottom of the page.
WebShare RB300 Update: Click to update information for the virtual server if the user has selected a listed item and has made changes. Delete: Select a listed item and click “Delete” to remove the item from the list. Clear: Click to erase all fields and enter new information. If the DHCP server option is enabled, you have to be very careful in assigning the IP addresses of the virtual servers in order to avoid conflicts.
WebShare RB300 POP3 Email SUN Remote Procedure Call (RPC) Network News Transfer Protocol (NNTP) Network Time Protocol (NTP) News Simple Management Network Protocol (SNMP) SNMP (traps) Border Gateway Protocol (BGP) Secure HTTP (HTTPS) rlogin rexec talk ntalk Open Windows Network File System (NFS) X11 Routing Information Protocol (RIP) Layer 2 Tunnelling Protocol (L2TP) Pag.
WebShare RB300 3.7.3 Special AP This screen enables users to specify special applications, such as games which require multiple connections that are blocked by NAT. The special applications profiles are listed in the table at the bottom of the page. Note: When selecting items in the table at the bottom, click anywhere in the item. The line is selected, and the fields automatically load the item's parameters, which user can edit. Enable: Click to enable or disable the application profile.
WebShare RB300 Protocol: Select the protocol TCP or UDP that can be used to access the application, the “*” is meaning to both of TCP and UDP protocols. Port Range: Type the port range that can be used to access the application in the text boxes. Incoming: Defines which incoming communications users are permitted to connect with. Protocol: Select the protocol TCP or UDP that can be used by the incoming communication, the “*” is meaning to both of TCP and UDP protocols.
WebShare RB300 3.7.4 DMZ The DMZ function enables users to create a DMZ for those computers that cannot access Internet applications properly through the Wireless Broadband Router and associated security settings. Enable: Click to enable or disable the DMZ. DMZ Host IP: Type a host IP address for the DMZ. The computer with this IP address acts as a DMZ host with unlimited Internet access. Click Apply to save.
WebShare RB300 3.7.5 Firewall Settings A firewall protects your network from the outside world, this screen enables users to setup the simple firewall function on the wireless router. Endpoint Independent: Any incoming traffic sent to an open port will be forwarded to the application that opened the port. Address Restricted: Incoming traffic must match the IP address of the outgoing connection. Address And Port Restriction: Incoming traffic must match the IP address and port of the outgoing connection.
WebShare RB300 3.8 System This system setting enables users to change password, set the device time, view the device information, restart the system, save and load different settings as profiles, restore factory default settings, upgrade the firmware, and ping remote IP addresses….etc. 3.8.1 Password This function enables users to set administrative and user passwords. These passwords are used to gain access to the Wireless Broadband Router interface. Click Apply to save. Pag.
WebShare RB300 3.8.2 Time This function enables users to set the time and date for the Wireless Broadband Router’s real-time clock, select properly time zone, and enable or disable daylight saving. Local Time: Displays the local time and date. Time Zone: Select the time zone from the drop-down list. Synchronize the clock with NTP Server: Enable or disable the Wireless Broadband Router automatically adjust the system time from NTP Server.
WebShare RB300 Manually Date and Time Setting: Manually setting the Wireless Broadband Router system time, press the Set Time button to update the system time. Daylight Saving: Enables users to enable or disable daylight saving time. When enabled, select the start and end date for daylight saving time. Click Apply to save. 3.8.3 Device Information This function enables users to view the Wireless Broadband Router’s WAN, Wireless, LAN and System configurations. Pag.
WebShare RB300 WAN: This section displays the WAN interface configuration including the MAC address, Connection status, DHCP client status, IP address, Subnet mask, Default gateway, and DNS. Wireless: This section displays the wireless configuration information, including the MAC address, the Connection status, SSID, Channel and Authentication type. LAN: This section displays the LAN interface configuration including the MAC address, IP Address, Subnet Mask, and DHCP Server Status.
WebShare RB300 3.8.4 Log This function enables users to view a running log of Router system statistics, events, and activities. The log displays up to 200 entries. Older entries are overwritten by new entries.
WebShare RB300 3.8.5 Log Settings This function enables users to set Router Log parameters. SMTP Authentication: Selected the Enabled if the SMTP server need for authentication, fill in account name and password in SMTP Account field and SMTP Password field. SMTP Account: If the SMTP Authentication enabled, fill in the SMTP account name here. SMTP Password: If the SMTP Authentication enabled, fill in the password of the SMTP account here. SMTP Server: Type your SMTP server address here.
WebShare RB300 Syslog Server: Type the IP address of the Syslog Server if user wants the Wireless Broadband Router to listen and receive incoming Syslog messages. Log Type: Enables users to select what items will be included in the log: System Activity: Displays information related to Wireless Broadband Router operation. Debug Information: Displays information related to errors and system malfunctions. Attacks: Displays information about any malicious activity on the network.
WebShare RB300 3.8.6 Statistics This function displays a table that shows the rate of packet transmission via the Wireless Broadband Router’s LAN, WAN and Wireless ports (in bytes per second). Click Reset to erase all statistics and begin logging statistics again. 3.8.7 Restart Click Restart to restart the system in the event the system is not performing correctly. Pag.
WebShare RB300 3.8.8 Firmware This function enables users to keep the Wireless Broadband Router firmware up to date. Please follow the below instructions: Download the latest firmware from the Atlantis Land’s Web site, and save it to disk. Click Browse and go to the location of the downloaded firmware file. Select the file and click Upgrade to update the firmware to the latest release. Pag.
WebShare RB300 3.8.9 Configuration This function enables users to save settings as a profile and load profiles for different circumstances. User can also load the factory default settings, and run a setup wizard to configure the Wireless Broadband Router and Router interface. SAVE SETTINGS Click on Save Settings button, which will open a FileSave Dialog box, where user gets to save all the current settings and configurations to a file.
WebShare RB300 RESTORE FACTORY DEFAULT SETTINGS Click on Restore button to restore the access point back to its manufacture default settings. 3.8.10 UPnP This function enables users to enable or disable the UPnP function on the Wireless Broadband Router. UPnP: Select to enable or disable the UPnP function on the WLAN Router. UPnP is short for Universal Plug and Play that is a networking architecture that provides compatibility among networking equipment, software, and peripherals.
WebShare RB300 3.8.11 Ping Test The ping test enables users to determine whether an IP address or host is present on the Internet. Type the host name or IP address in the text box and click Ping button to start the Ping test. Pag.
WebShare RB300 3.8.12 Remote Management This function enables users to set up remote management. Using remote management, the Wireless Broadband Router can be configured through the WAN via a Web browser. A user name and password are required to perform remote management. HTTP: Enables users to set up HTTP access for port number, and Remote IP Range for remote management.
WebShare RB300 APPENDIX A: Troubleshooting This chapter covers potential problems on Wireless Broadband Router Point and the corresponding remedies. A.1 LEDs The LEDs are useful aides for finding possible problem causes. A.1.1 LED Power The PWR LED on the front panel does not light up. Steps CORRECTIVE ACTION 1 Make sure that the Wireless Broadband Router power adaptor is connected to the device and plugged in to an appropriate power source. Use only the supplied power adaptor.
WebShare RB300 A.1.3 LED WLAN The WLAN LED on the front panel does not light up. Steps CORRECTIVE ACTION 1 Press the “Reset” button on the rear panel of the Wireless Broadband Router, to set back to factory default setting. Please unplug AC Adaptor and replug-it. If these steps fail to correct the problem, contact your local distributor for assistance. 2 3 A.2 WEB I cannot access the web configurator.
WebShare RB300 A.3 Login If you forget the password to log in. Steps CORRECTIVE ACTION 1 The Reset function is to reset the setting back to factory default setting, once you press the “RESET” button within 15 seconds, the LED of the WLAN will turn off. And when the device is ready, the WLAN LED will start blinking. 2 3 Before configurating this Wireless Broadband Router, you need to know the following default settings. Username: admin Password : admin IP Address : 192.168.1.1 Subnet Mask : 255.255.
WebShare RB300 A.5 FAQ Question Answer Question Answer Question Answer Question Answer Can I run an application from a remote computer over the wireless network? This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network. Can I play computer games with other members of the wireless network? Yes, as long as the game supports multiple players over a LAN (local area network).
WebShare RB300 bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. Question Answer Question Answer Question Answer Question Answer Would the information be intercepted while transmitting on air? WLAN features two-fold protection in security.
WebShare RB300 part of 802.11i specifics. WPA2 introduce all IEEE802.11i specifics, like support for Advanced Encryption Standard (AES), encryption protocol use also in VPN IpSEC. WPA2 devices will be compatible with WPA device, but they will be updated through new driver and firmware. NetFly AP2-54M supports WPA2 without performance reduction.
WebShare RB300 local area networks (WLANs), 802.11g offers wireless transmission over relatively short distances at up to 54 megabits per second (Mbps) compared with the 11 megabits per second of the 802.11b (Wi-Fi) standard. Like 802.11b, 802.11g operates in the 2.4 GHz range and is thus compatible with it.
WebShare RB300 We suggest to upgrade WLAN to IEEE802.11g. Question How I can eliminate interferences in WLAN? Answer We suggest to turn off (or place far) any device that operate in the same frequencies and use directional antennas to reduce noise. Question Antenna Specifications Choose properly antenna, any incorrect choose can damage product. It can be follow specifications: Reverse SMA connector compatible with IEEE 802.11 standard (2.
WebShare RB300 APPENDIX B: Regulations Some countries use different laws about ISM band frequency use. Please to make reference to follow table: Channel Country 1-11 USA/CANADA 1-13 ETSI(Europe) 10-11 Spain 10-13 France 14 MKK 1-14 Japan (MKKI Telecom) 3-9 Israel 5-13 Israel Pag.
WebShare RB300 APPENDIX C: Technical Features STANDARDS PROTOCOL RADIO TECHNOLOGY DATA TRANSFER RATE RECEIVER SENSITIVITY TX POWER NETWORK CABLES FREQUENCY RANGE MODULATION SCHEMES SECURITY CHANNELS NUMBER OF PORTS DC INPUTS POWER CONSUMPTION TEMPERATURE HUMIDITY DIMENSIONS EMI IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.11g; IEEE 802.11b CSMA/CD with ACK DSSS/OFDM 802.11n mode: up to 300Mbps (auto sense) 802.11g mode: up to 54Mbps (auto sense) 802.
WebShare RB300 APPENDIX D: Support If you have any problems with the Wireless Broadband Router, please consult this manual. If you continue to have problems you should contact the dealer where you bought this device. If you have any other questions you can contact the Atlantis Land company directly at the following address: Atlantis Via Pelizza da Volpedo, 59 20092 Cinisello Balsamo (MI) Italy Tel: +39.(0)2.93906085 Fax: +39.(0)2.66016.666 Help Desk :+39.(0)2.93907634 Email: info@atlantis-land.
