WIRELESS ROUTER ADSL A02-RA240-W54 A02-RA210-W54 MULTILANGUAGE QUICK START GUIDE A02-RA24(1)0-W54_GX01
MULTILANGUAGE QUICK START GUIDE ITALIANO 1.1 Contenuto della confezione..................................... 5 1.2 I LED frontali.......................................................... 5 1.3 Le porte posteriori................................................... 6 1.4 Cablaggio ................................................................ 7 1.5 Settaggi di Default .................................................. 8 1.6 Configurazione di IE............................................... 8 1.
MULTILANGUAGE QUICK START GUIDE PPPoE routed/PPPoA routed .................................. 31 RFC1483 routed / IpoA routed ............................... 33 FRANCAIS 1.1 Contenu de la boîte ............................................... 36 1.2 Face avant ............................................................. 37 1.3 Face arrière............................................................ 38 1.4 Câblage.................................................................. 39 1.
MULTILANGUAGE QUICK START GUIDE Konfiguration des PC in Windows XP ................... 56 1.8 Konfiguration des Router...................................... 59 PPPoE routed/PPPoA routed .................................. 61 RFC1483 routed / IpoA routed ............................... 63 A02-RA24(1)0-W54_GX01(V1.
ITALIANO Questo manuale è inteso come una guida rapida, pertanto per ulteriori dettagli sulla configurazione fare riferimento al manuale esteso presente sul CD. 1.1 Contenuto della confezione Atlantis Land Wireless Router ADSL, CD-ROM contenente il manuale, Guida di Quick Start, cavo RJ-11 ADSL, cavo CAT-5 LAN , Alimentatore (12V, 1A). 1.
ITALIANO 1.3 Le porte posteriori PORTE UTILIZZO Line(RJ11) Connettere il cavo RJ-11 a questa porta per effettuare l’allacciamento all’ADSL. LAN(1/4*RJ-45) Connettere con un cavo UTP Reset Dopo che il dispositivo è acceso, premere per effettuare il reset o il restore.
ITALIANO 1.4 Cablaggio Anzitutto collegare il prodotto alla linea ADSL tramite il cavo RJ11 fornito in dotazione (nella porta LINE), poi collegare alle porte RJ45 i PC della Lan oppure eventuali Switch. E’ possibile accedere al Router tramite i diversi client wireless compatibili con lo standard IEEE802.11b o IEEE802.11g. Infine collegare l’alimentatore al Wireless Router ADSL e poi presa elettrica.
ITALIANO 1.5 Settaggi di Default Prima di iniziare la configurazione dell’Atlantis Wireless Router ADSL è necessario conoscere quali siano i settaggi di default. Lasciando questi settaggi e impostando i PC come client DHCP (come da istruzioni seguenti) ed infine configurando la connessione all’ISP (che avrà comunicato tutti i parametri del caso) è possibile utilizzare l’Atlantis Wireless Router ADSL in pochissimo tempo. Per una configurazione più dettagliata fare riferimento al manuale presente sul CD.
ITALIANO 2. Selezionare TCP/IP->NIC F/E, o qualsiasi Network Interface Card (NIC) del PC. 3. Cliccare su Properties. 4. Selezionare l’opzione Obtain an IP address automatically (dopo aver scelto IP Address). 5. Andare su DNS Configuration. 6. Selezionare l’opzione Disable DNS e premere su OK per terminare la configurazione. Riavviare il PC affinché i cambiamenti abbiano effetto. Configurazione del PC in Windows NT4.0 1. Andare su Start/Settings/ Control Panel.
ITALIANO Configurazione del PC in Windows 2000 1. Andare su Start/Settings/Control Panel. Cliccare due volte su Network and Dial-up Connections. 2. Cliccare due volte su Local Area Connection. 3. In Local Area Connection Status cliccare Properties. 4. Selezionare Internet Protocol (TCP/IP) e cliccare su Properties. 5. Selezionare l’opzione Obtain an IP address automatically e successivamente Obtain DNS server address automatically. 6. Premere su OK per terminare la configurazione.
ITALIANO 3. In Local Area Connection Status cliccare Properties. 4. Selezionare Internet Protocol (TCP/IP) e cliccare su Properties.
ITALIANO 5. Selezionare l’opzione Obtain an IP address automatically e successivamente Obtain DNS server address automatically. 6. Premere su OK per terminare la configurazione.
ITALIANO 1.8 Configurazione Router Accedere col browser web al seguente indirizzo IP che di default è: 192.168.1.254, e premere il tasto invio. Utilizzare admin (come nome utente) e atlantis (come password). Premere OK per continuare.
ITALIANO Cliccando sulla sezione desiderata, nello spazio della homepage appariranno tutti i settaggi relativi alla configurazione della sezione scelta, oppure si apriranno tutta una serie di sottosezioni tra cui scegliere prima di avere accesso alle configurazione vere e proprie. Seguendo i successivi passi è possibile rendere operativo il Wireless ADSL Router in pochissimo tempo a patto di usare le macchine della Lan configurate come client DHCP.
ITALIANO PPPoE routed/PPPoA routed PPPoE/PPPoA sono connessioni ADSL conosciute come dial-up DSL. Sono state concepite per integrare servizi a banda larga con un’attenzione particolare alla facilità di configurazione. L’utente può beneficiare di una grande velocità di accesso senza cambiare l’idea di funzionamento, condividere lo stesso account con l’ISP.
ITALIANO invece PPPoE LLC (più raramente PPPoE VC-MUX) in caso di PPPoE. • Bridge:Disable • VPI:8 • VCI:35 • IP Adress:0.0.0.0 • Subnet Mask:0.0.0.0 • Gateway:0.0.0.0 • Username: Introdurre l’username fornita dall’ISP (case sensitive). • Password: Introdurre la password fornita dall’ISP (case sensitive). • Automatic Reconnect: spuntare per consentire al dispositivo la riconnessione automatica. Premere Submit, poi cliccare su Save Config. Apparirà la seguente immagine.
ITALIANO RFC1483 routed / IpoA routed Controllare che i parametri siano come in figura: • Virtual Circuit:Enable • Encapsulation: Scegliere l’incapsulamento 1483 Routed IP LLC (più raramente 1483 Routed VC-Mux) in caso di RFC 1483. Scegliere invece Classical IP over ATM in caso di RFC1577.
• • • ITALIANO IP Adress:Introdurre l’indirizzo IP fornito dall’ISP Subnet Mask: Introdurre la subnet mask fornita dall’ISP Gateway:Introdurre l’indirizzo IP del default Gateway fornito dall’ISP • Username: lasciare vuoto • Password: lasciare vuoto • Automatic Reconnect: lasciare non spuntato Premere Submit, poi cliccare su Save Config. Apparirà la seguente immagine. Cliccare su Submit per rendere i settaggi permanenti. Il Led ADSL prima lampeggerà e poi diventerà fisso indicando l’avvenuto allineamento.
ENGLISH For more detailed instructions on configuring and using the Wireless Router ADSL, please refer to the online manual. Before beginning the configuration of the Router you have to know the parameters of your subscription ADSL. There are five ways ─ PPPoE, PPPoA, RFC1483 routed, IPoA, RFC1483 Bridge─ for the device to have a public IP address and then to access Internet. You have to check with your ISP about which way is adopted.
ENGLISH RFC1483 Routed VPI/VCI VC-based / LLC-based multiplexing IP address Subnet mask Default Gateway (IP address) IP address (DNS) IPoA VPI/VCI IP address Subnet mask Default Gateway (IP address) IP address (DNS) 1.1 Package contents Atlantis Land Wireless Router ADSL, CD-ROM with manual, Quick Start Guide, cable RJ-11 ADSL, cable CAT-5 LAN, Power Adapter AC-DC (12V, 1A).
ENGLISH 1.2 The Front Panel LEDs LED MEANING Power Lit when power ON Sys Blinking when system is ready WLan Lan ADSL Lit green when the wireless connection is established. Flashes when sending/receiving data.
ENGLISH 1.3 The Rear Ports PORT MEANING Line (RJ11) Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. LAN (1/4 * RJ-45) Connect an UTP Ethernet cable to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps. POWER (jack) After the device has turned on, press it to reset the device or restore to factory default settings.
ENGLISH 1.4 Cabling First you must connect the product to the ADSL line through the RJ11 cable you have in equipment (in the port LINE), then connect to the RJ45 ports the PCs of your Lan or others Switch. You can get to the Router through the different client wireless compatible with the IEEE802.11b & IEEE802.11g standard. In the end connect the feeder to the Wireless Router ADSL and then to the socket.
ENGLISH configure the PC to get an IP address from the Wireless ADSL Router ADSL. Please follow the steps below for PC’s network environment installation. First of all, please check your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to MS Windows relative manuals. Before you configure this Wireless ADSL Router, you need to know the following default settings: • Username:admin • Password:atlantis • IP address (192.168.1.
ENGLISH 1.7 TCP/IP Configuration Configuring PC (Windows 95/98/ME) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP / IP -> NIC Compatible, or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties. 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. 5. Then select the DNS Configuration tab. 6.
ENGLISH Configuring PC (Windows 2000) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC (WindowsXP) 1.
ENGLISH 3. In the LAN Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons.
ENGLISH 6.
ENGLISH 1.8 Browser configuration Open the web browser, enter the local port IP address of this Wireless Router ADSL, which default at 192.168.1.254, and click “Go” to get the login page. The default username is admin, password atlantis and click “OK” to continue.
ENGLISH Click on the desired item to expand the page with all settings in the main navigation pane. Following next steps you can make operating Wireless Router ADSL in short time using PCs in DHCP mode. Refer to manual on Installation CD if you need personalized configuration. Click on Quick Start to perform an automatic protocol selection.
ENGLISH PPPoE routed/PPPoA routed PPPoA/PPPoE is known as a dial-up DSL or cable service. It is designed to integrate the broadband services into the current widely deployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Therefore, users can get greater access speed without changing the operation concept, sharing the same ISP account and paying for one access account.
• ENGLISH Encapsulation: There are 5 ways :PPPoE VC-Mux, PPPoE LLC, PPPoE None, PPPoA VCMux, and PPPoA LLC. You have to check with your ISP about which way is adopted. • Bridge:Disable • VPI:0 or 1 (Consult the ISP) • VCI:38 or 50 (Consult the ISP) • IP Adress:0.0.0.0 • Subnet Mask:0.0.0.0 • Gateway:0.0.0.0 • Username: Enter the username provided by your ISP(case sensitive). • Password: Enter the password provided by your ISP (case sensitive).
ENGLISH RFC1483 routed / IpoA routed These are configuration parameters: • • • • Virtual Circuit:Enable Encapsulation: There are 3 ways :1483 Routed IP LLC, 1483 Routed IP VC-MUX or Classical IP over ATM ( RFC 1577). You have to check with your ISP about which way is adopted.
• VCI:38 or 50 (Consult the ISP) • IP Adress: Insert your Public IP • Subnet Mask: Insert Netmask provided by ISP • Gateway: Insert router Default Gateway Press Submit and then click on Save Config. ENGLISH Press again Submit. to reboot the Router. To this point approaching the section Status you will be able to check if connection is up, now you can begin navigation. For every other problem refer to manual on attached cd-rom.
FRANCAIS Ce guide d’installation rapide vous permet d’installer et de configurer le Wireless Router ADSL suivant des paramètres standards. Pour plus de précisions, tant sur les méthodes de configuration que sur le paramétrage avancé, reportez-vous au manuel sous format électronique (PDF) disponible sur le CD Rom fourni. Avant d’installer votre Wireless Router ADSL, vous devez savoir de quel type d'accès vous disposez et vous munir d'informations précises concernant votre compte internet.
FRANCAIS RFC1483 Bridged VPI/VCI RFC1483 Routed VPI/VCI VC-based ou LLC-based multiplexing VC-based ou LLC-based multiplexing Adresse IP Masque de sous-réseau Adresse IP du Default Gateway Adresses IP des serveurs DNS IPoA VPI/VCI VC-based ou LLC-based multiplexing Adresse IP Masque de sous-réseau Adresse IP du Default Gateway Adresses IP des serveur DNS 1.
FRANCAIS 1.2 Face avant LED SIGNIFICATION Power Allumé quand le Wireless Router ADSL est sous tension Sys Allumé pour indiquer que le système est actif WLan Lan ADSL Clignotant vert pour indiquer transmission des données. Allumé vert fixé il indique le correct fonctionnement de module wireless.
FRANCAIS 1.3 Face arrière PORT USAGE Line(RJ11) Connectez le câble (fourni) RJ11 au filtre ADSL (optionnel) et enfin à la prise téléphonique LAN (1/4 * RJ-45) Relier directement avec un câble Ethernet standard ou croisé aux PC ou à un port uplink (Hub/Switch). Reset (remise à zéro) Dispositif allumé, presser pour effectuer le reset ou le restore.
FRANCAIS 1.4 Câblage Après avoir terminé le câblage, raccordez l’alimentation pour mettre le ireless Router ADSL sous tension. Assurez-vous que les LEDs sont correctement allumés. Connectez un câble réseau standard ou croisé pour relier le Router à un Hub/Switch ou aux PC. L’interface Wireless intégrée permet aux utilisateurs dotés d’interfaces wireless d’aller sur Internet en utilisant le protocole IEEE802.11b ou IEEE802.11g.
FRANCAIS 1.6 Configuration du TCP/IP Configuration sous Windows 95/98/ME 1. Allez dans Panneau de Configuration. Double-cliquez sur Réseau.et enfin affichez l’onglet Configuration. 2. Sélectionnez le protocole TCP/IP -> NIC carte, ou quelconque carte réseau Ethernet dans le PC. 3. Cliquez sur Propriétés 4. Dans l’onglet Adresse IP Sélectionnez l’option « obtenir automatiquement une adresse IP ». 5. Sélectionnez l’onglet DNS. 6.
FRANCAIS Configuration sous Windows 2000 1. Allez au Panneau de Configuration. Double-cliquez sur Connexions Réseau et accès à distance.. 2. Double-cliquez sur connexion au réseau local. 3. Dans Connexion au réseau local cliquez sur Propriétés. 4. Sélectionnez Internet Protocol (TCP/IP) et cliquez sur Propriétés. 5. Sous l’onglet Général, sélectionnez l’onglet Obtenir une adresse IP automatiquement et après Obtenir les adresses des serveurs DNS automatiquement 6.
FRANCAIS 3. Cliquez Propriétés.
FRANCAIS 4. Sélectionnez Internet Protocol (TCP/IP) et cliquez sur Properties. 5. Sélectionnez Obtenir une adresse IP automatiquement et après Obtenir les adresses des serveurs DNS automatiquement. 6. Cliquez sur OK pour terminer la configuration.
FRANCAIS 1.7 Vérification Pour vérifier le succès de la configuration (après avoir redémarré le PC, opération nécessaire sous Win98, SE, ME) utiliser le PING. Dans la fenêtre Dos écrivez: PING 192.168.1.254 Si le message suivant apparaît: Pinging 192.168.1.254 with 32 bytes of date: Reply from 192.168.1.254: bytes=32 times <10ms TTL=64 Reply from 192.168.1.254: bytes=32 times <10ms TTL=64 Reply from 192.168.1.254: bytes=32 times <10ms TTL=64 Vous pouvez procéder en allant au point suivant (1.
FRANCAIS 1.8 Configuration avec le Browser Pour accéder à l’interface Web, lancez un navigateur Internet et tapez dans la barre adresse l’IP suivante : http://192.168.1.254 Un mot de passe vous est demandé, pour la première connexion. User = admin Password = atlantis et appuyez sur OK pour aller dans la configuration.
FRANCAIS En suivant les indications ci-dessous il est possible de rendre opérationnel le Wireless Router ADSL en peu de temps à condition d'utiliser les PC du réseau comme client DHCP. Pour une configuration personnalisée du réseau et du Router faire référence au manuel complet dans le CD Rom. Vous trouverez dans le tableau ci-dessous les valeurs possibles de VPI/VCI.
FRANCAIS PPPoE Routed /PPPoA Routed Le protocole PPPoE (Point to Point Protocol over Ethernet) est l’une des méthodes utilisées en France. Il a été conçu (comme le PPPoA) pour compléter le service ADSL avec une attention spéciale pour facilité la configuration. L'utilisateur peut bénéficier d'une grande vitesse d'accès sans changer la façon de fonctionnement et en même temps partager entre tous les utilisateurs de votre entreprise un compte Internet unique (avec le FAI).
FRANCAIS • • Virtual Circuit:Enable Encapsulation: Choisir PPPoE LLC, ou, plus rarement, PPPoE VC-Mux, en cas de PPPoE. Dans le cas de PPPoA choisir par contre PPPoA VC-Mux ou PPPoA LLC. • Bridge:Disable • VPI:8 ou 8 ou 2 (contacter le FAI) • VCI:67 ou 35 ou 32 (contacter le FAI) • IP Adress:0.0.0.0 • Subnet Mask:0.0.0.0 • Gateway:0.0.0.0 • Username: Nom d’utilisateur(case sensitive).
FRANCAIS RFC1483 routed / IpoA routed • • • • • • • Virtual Circuit:Enable Encapsulation: 1483 Routed IP LLC ou 1483 Routed IP VC-MUX en cas de RFC 1483 Routed. Choisir Classical IP over ATM en cas de RFC 1577 Bridge:Disable VPI:8 ou 8 ou 2 (contacter le FAI) VCI:67 ou 35 ou 32 (contacter le FAI) Static IP Address= introduisez l’adresse IP Subnet Mask= introduisez le masque de sous-réseau.
• FRANCAIS Gateway= remplissez les champs suivants avec les caractéristiques de votre abonnement ADSL (l’adresse IP du Default Gateway) • Username: • Password: • Automatic Reconnect: ne cochez pas cette En pressant submit, le Wireless Routeur ADSL fera un reboot automatique [ADSL doit être Allumée fixe lorsque la session PPPoE/PPPoA est connectée], votre PC sera prêt pour la navigation. Presser sur Save Config (et enfin Submit) pour terminer.
DEUTSCH Das ist ein Handbuch,das wie eine kurze Anleitung ausgedacht wird, deshalb nehmen Sie Bezug auf das vollig Hanbuch, das im CD ist,wenn Sie weitere Einzelheiten uber die Konfiguration brauchen. 1.1 Inhalt der Verpackung Atlantis Land Wireless Router ADSL, CD-ROM,der das Handbuch enthalt, Quick Start Anleitung, Kabel RJ-11 ADSL, Kabel CAT-5 LAN , Speiseleitung (12V, 1A). 1.
DEUTSCH 1.3 Die Hinterturen TUREN Line(RJ11) LAN (1/4* RJ45) Reset POWER (jack) POWER Switch BENUTZUNG Verbinden Sie den RJ-11 Kabel zu diesem Tur,um den Anschluss zum ADSL durchzufuhren. Verbinden Sie mit einem UTP Kabel. Nachdem die Vorrichtung eingeschaltet ist,drucken Sie auf die Taste,um der reset oder der restore zu machen.
DEUTSCH 1.4 Verdrahtung Zunächst müssen Sie das Produkt dem ADSL Linie durch das gegebenen RJ11 Kabel (in die LINE Tur), verbinden, dann verbinden Sie die PC Ihrer Lan oder die Switch den Türen RJ45. Sie können den Router erreichen, durch die verschiedene client wireless, die kompatibel mit dem Standard IEEE802.11b und IEEE802.11g sind. Schliesslich verbinden Sie der Speiser dem Router Wireless und dann der Steckdose.
• • • DEUTSCH Adresse IP (192.168.1.254), Subnet Mask (255.255.255.0) DHCP Server staatlich SSSID= wlan-ap, Channel=6, WEP=unfähig 1.6 Die IE Konfiguration Jeztz ist es notwendig,IE einzufuhren, in Menu Instrument zu gehen, dann der tab Verbindungen wahlen und eine der folgende Stimmen zu wahlen: • Benutzen Sie nie remote Verbindung • Benutzen Sie remote Verbindung, wenn es keine netz Verbindung disponibel ist. 1.7 Konfiguration des PC Konfiguration des PC in Windows 95/98/ME 1.
DEUTSCH Konfiguration des PC in Windows NT4.0 1. Gehen Sie auf Start/Settings/ Control Panel. Drucken Sie zweimal auf Network und dann auf Protocols . 2. Wahlen Sie TCP/IP Protocol dann drucken Sie auf Properties. 3. Wahlen Sie den Option Obtain an IP address from a DHCP server und drucken Sie auf OK Konfiguration des PC in Windows 2000 1. Gehen Sie auf Start/Settings/Control Panel. Drucken Sie zweimal auf Network and Dial-up Connections. 2. Drucken Sie zweimal auf Local Area Connection. 3.
DEUTSCH Konfiguration des PC in Windows XP 1. Gehen Sie auf Start dann auf Control Panel. Drucken Sie zweimal auf Network (in Classic View) Connections. 2. Drucken Sie zweimal auf Local Area Connection. 3. In Local Area Connection Status drucken Sie auf Properties.
DEUTSCH 4. Wahlen Sie Internet Protocol (TCP/IP) und drucken Sie auf Properties. 5. Wahlen Sie die Option Obtain an IP address automatically und spater Obtain DNS server address automatically . 6. Drucken Sie auf OK,um die Konfiguration zu enden..
DEUTSCH 58
DEUTSCH 1.8 Konfiguration des Router Mit dem browser web, kommen Sie in den folgenden IP Adresse (wo man den URL steckt)dessen default ist: 192.168.1.254,und drucken Sie die Taste Ubersendung. Benutzen Sie admin (als user name) und atlantis (als password). Drucken Sie OK, um weiter zu gehen.
DEUTSCH Wenn man auf die gewunschte Abschnitt druckt,wird man im Raum des Homepage alle Einstellung des gewahlten Konfiguration sehen,oder eine Reihe von Abschnitte wird offnen,und Sie kann unter sie wahlen,bevor Sie in den wahre Konfigurationen kommen. Wenn Sie die nachste Schnitten folgen,konnen Sie in kurze Zeit den Wireless ADSL Lan Router operativ machen,unter der Bedingung,dass Sie die als client DHCP eingestellten Lan Maschinen benutzen.
DEUTSCH PPPoE routed/PPPoA routed PPPoE/PPPoA sind ADSL Verbindungen,und sie sind als dial-up DSL bekannt.Sie sind ausgedacht werden,um Weitstreifen Verbindungen zu erganzen,.mit einer besonders Aufmerksamkeit der Leichtigkeit des Konfiguration. Der Benutzer kann eine grosse Zugriffschnelligkeit geniessen, ohne die Arbeitsweise zu andern,und derselbe account mit ISP teilen.
• • • • • • • • DEUTSCH Encapsulation:PPPoA VC-Mux, PPPoA LLC, PPPoE LLC, PPPoE VC-Mux VPI: 8 (ISP) VCI: 35 (ISP) IP Adress:0.0.0.0 Subnet Mask:0.0.0.0 Gateway:0.0.0.0 Username: Stecken Sie den von Ihren ISP gegebenen username (case sensitive). Password: Stecken Sie den von Ihren ISP gegebenen Password (case sensitive). Drucken Sie auf Submit,um die neue Konfiguration operativ zu machen.
DEUTSCH RFC1483 routed / IpoA routed Sehen wir den Paremeter, die man darstellen muss: • Virtual Circuit: Disable • Encapsulation: Encapsulation Method(es gibt nur in RFC1483 routed):Wahlen Sie die Einkapselungmethode Ihres provider. 1483 Routed IP LLC(RFC1483), Classical IP over ATM (RFC1577) • VPI: 8 (ISP) • VCI: 35 (ISP) • IP Adress: Stecken Sie Ihren offentlich IP.
• • • • DEUTSCH Subnet Mask: Stecken Sie die von ISP gegebene Netmask. Gateway: Stecken Sie den Default Gateway des Router. Username: Password: Drucken Sie auf Submit,um die neue Konfiguration operativ zu machen.Wenn Sie die Konfiguration beendet haben,drucken Sie auf Save Config (dann auf Submit),um die Einstellung dauernd zu machen. Jetzt,wenn Sie in die Sektion Status kommen, konnen Sie die geschehene Verbindung kontrollieren und die Schutzstand zu beginnen.