WIRELESS ROUTER ADSL A02-RA240-W54 A02-RA210-W54 USER’S MANUAL A02-RA24(1)0-W54_ME01
WIRELESS ROUTER ADSL Copyright The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned mat be trademarks or registered trademarks of their respective owners. Subject to change without notice. No liability for technical errors and/or omissions. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
WIRELESS ROUTER ADSL TABLE OF CONTENTS CHAPTER 1............................................... 1 1.1 AN OVERVIEW OF THE WIRELESS ROUTER ADSL .......................................................................... 1 1.2 PACKAGE CONTENTS ...................................................................................................................... 1 1.3 WIRELESS ROUTER ADSL FEATURES............................................................................................. 2 1.
WIRELESS ROUTER ADSL 3.8.2.4.3 Upgrade................................................................................................................... 32 3.8.2.4.4 Factory Settings ...................................................................................................... 33 3.8.2.4.5 Restart ..................................................................................................................... 33 3.8.2.5 Firewall ..................................................................
WIRELESS ROUTER ADSL Chapter 1 Introduction 1.1 An Overview of the Wireless Router ADSL Broadband Sharing and IP sharing The Wireless Router ADSL supports 4 ports 10/100 Mbps auto-negotiating Fast Ethernet for connection to your local area network (LAN) and downstream (with built-in ADSL modem) rate up to 8Mbps. Power by NAT technology, dozens of network users can surf on the Internet and share the ADSL connection simultaneously by using one ISP account and one single IP address.
WIRELESS ROUTER ADSL 1.3 Wireless Router ADSL Features Wireless ADSL Router provides the following features: • ADSL Multi-Mode Standard: Supports downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1024Kbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.lite (G992.2).
• WIRELESS ROUTER ADSL Dynamic Domain Name System (DDNS): The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to use the service, you must first apply an account from this free Web server http://www.dyndns.org/. There are more than 5 DDNS servers supported. • Virtual Private Network (VPN): Allows a user to make a tunnel with a remote site directly to secure the data transmission among the connection.
WIRELESS ROUTER ADSL 1.
WIRELESS ROUTER ADSL Chapter 2 Using Wireless Router ADSL 2.1 Cautions for using the Wireless Router ADSL Do not place the ADSL Wireless Router under high humidity and high temperature. Do not use the same power source for ADSL Wireless Router with other equipment. Do not open or repair the case yourself. If the ADSL Wireless Router is too hot, turn off the power immediately and have a qualified serviceman repair it. Place the ADSL Wireless Router on a stable surface.
WIRELESS ROUTER ADSL 2.3 The Rear Ports PORT Meaning Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. Connect an UTP Ethernet cable to one of the LAN four LAN ports when connecting to a PC or an (4 *RJ-45)* office/home network of 10Mbps or 100Mbps. After the device has turned on, press it to reset RESET the device or restore to factory default settings.
WIRELESS ROUTER ADSL Chapter 3 Configuration The ADSL Wireless Router can be configured with your Web browser. The web browser is included as a standard application in the following operation systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/Me, and etc. The product provides a very easy and user-friendly interface for configuration. 3.
WIRELESS ROUTER ADSL 3.3 Configuring PC in Windows For Windows 95/98/ME 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. 3. 4. Click Properties. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button.
WIRELESS ROUTER ADSL 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click “OK” to finish the configuration.
WIRELESS ROUTER ADSL For Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click “OK”.
WIRELESS ROUTER ADSL For Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties.
WIRELESS ROUTER ADSL 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click “OK” to finish the configuration.
WIRELESS ROUTER ADSL For Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2. Double-click Local Area Connection 3. In the LAN Area Connection Status window, click Properties.
WIRELESS ROUTER ADSL 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons 6. Click “OK” to finish the configuration.
WIRELESS ROUTER ADSL 3.4 Factory Default Settings Before configurating this ADSL Wireless Router, you need to know the following default settings. • Username: admin • Password : atlantis • IP Address : 192.168.1.254 • Subnet Mask : 255.255.255.0 • DHCP server is enabled. • Wireless: SSSID= wlan-ap, Channel=6, WEP=disable 3.4.1 Username and Password The default username and password are admin and atlantis respectively.
WIRELESS ROUTER ADSL WAN Port LAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 DHCP server function Enabled N/A 3.5 Information from the ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service is provided such as PPPoE, PPPoA, RFC1483, IpoA. Gather the information as illustrated in the following table and keep it for reference.
WIRELESS ROUTER ADSL You will get a status report web page when login successfully.
WIRELESS ROUTER ADSL 3.6.1.1 ADSL Status the status of your ADSL connection. It will refresh every two seconds.
WIRELESS ROUTER ADSL 3.6.1.2 LAN Status Displays the status of your Local Area Network (LAN) connection. Display the status of TCP. This screen will automatically refresh every two seconds. 3.6.1.3 PPP Status Displays the status of your PPP connection. It will refresh every ten seconds. 3.6.1.4 VPN Connect Status When you click the VPN Connect Status, it gives you a quick view to know the ADSL Router’s current status. The status of VPN connection will be shown.
WIRELESS ROUTER ADSL 3.6.1.5 Learned MAC Table Aging Timeout: Enter the time period for the router to memorize MAC addresses. 3.6.1.5 Routing Table Display the current routing paths of A02-RA240-W54/A02-RA210-W54. 3.6.1.6 System Log Display the system logs cumulated till the present time. You can trace the historical information through this function.
WIRELESS ROUTER ADSL . 3.8.1.7 Security Log Display the information of security logs. If hacker attacks your sever, he will be isolated by the firewall function and the router will record related information. Hence, you know where the hacker comes from.
WIRELESS ROUTER ADSL 3.8.2 CONFIGURATION When you click this item, you get following sub-items to configure Wireless Router ADSL: • WAN • LAN • Wireless • System • Firewall • VPN • Virtual Server • Advanced 3.8.2.1 WAN Before you start installing this device, you have to check with your ISP what kind of service (connection method) is provided such as PPPoE, PPPoA, RFC1483 bridged or routed, IPoA. Gather the information as illustrated in the following table and keep it for reference.
WIRELESS ROUTER ADSL PPPoE(RFC 2516) / PPPoA(RFC 2364) Pvc0 is set as default and then press submit. The screens below contain settings for the WAN interface toward Internet. Virtual Circuit • Virtual Circuit=Enabled • Bridge=disabled • IGMP=disabled • Encapsulation= There are 5 ways :PPPoE VC-Mux, PPPoE LLC, PPPoE None, PPPoA VCMux, and PPPoA LLC. You have to check with your ISP about which way is adopted.
WIRELESS ROUTER ADSL MAC Spoofing • MAC Spoofing, The MAC Spoofing is for solving the scenario when the ISP only recognizing the specified MAC address. • MAC Address= 00:00:00:00:00:00 Static IP Settings • Static IP Address=0.0.0.0 • Subnet Mask=0.0.0.0 • Gateway=0.0.0.0 PPP • • • • Service name: This item is for identification purposes. If it is required, your ISP will provide you the information. Maximum input is 20 alphanumeric characters. Username: Enter the username provided by your ISP.
WIRELESS ROUTER ADSL MRU: Maximum Receive Unit indicates the peer of PPP connection the maximum size of the PPP information field this device can be received. The default value is 1492 and is used in the beginning of the PPP negotiation. In the normal negotiation, the peer will accept this MRU and will not send packet with information field larger than this value. • MTU: Maximum Transmission Unit indicates the network stack of any packet is larger than this value will be fragmented before the transmission.
WIRELESS ROUTER ADSL RFC 1483 Routing / Classical IP over ATM (RFC 1577) Pvc0 is set as default and then press submit. The screens below contain settings for the WAN interface toward Internet. Virtual Circuit • Virtual Circuit=Enabled • Bridge=disabled • IGMP=disabled • Encapsulation= There are 3 ways :1483 Routed IP LLC, 1483 Routed IP VC-MUX or Classical IP over ATM ( RFC 1577). You have to check with your ISP about which way is adopted.
WIRELESS ROUTER ADSL MAC Spoofing • MAC Spoofing, The MAC Spoofing is for solving the scenario when the ISP only recognizing the specified MAC address. • MAC Address= 00:00:00:00:00:00 Static IP Settings • Static IP Address= Enter the information provided by your ISP. • Subnet Mask= Enter the information provided by your ISP. • Gateway= Enter the information provided by your ISP. Press Submit and then click on Save Config. Press again Submit. to reboot the Router.
WIRELESS ROUTER ADSL 3.8.2.2 LAN This screen contains settings for LAN interface attached to the LAN port. 3.8.2.2.1 LAN Configuration IP Address: Default at 192.168.1.254. This is the device IP address in LAN site. If you plan to change it to another IP address to a different ange of IP subnet. Please make sure your PC is also located at the same IP subnet. Otherwise, you may not be able to access the router. Subnet Mask: Default at 255.255.255.0.
WIRELESS ROUTER ADSL Press again Submit. to reboot the Router. 3.8.2.3 Wireless When you click this item, you get following sub-items to configure Wireless Router ADSL: • Basic setting • Advanced setting • Wlan security 3.8.2.3.1 Base Settings ESSID: Enter the unique ID given to the Access Point (AP), which is already built-in to the router’s wireless interface. To connect to this device, your wireless clients must have the same ESSID as the device.
WIRELESS ROUTER ADSL Security: WEP Encryption: To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers highly secure data encryption, known as WEP. If you require high security for transmissions, there are two alternatives to select from: WEP 64 and WEP 128. WEP 128 will offer increased security over WEP 64. Passphrase: This is used to generate WEP keys automatically based upon the input string and a pre-defined algorithm in WEP64 or WEP128.
WIRELESS ROUTER ADSL 3.8.2.3.3 Wi-FI Protected Access(WPA) WPA-PSK: • Data Encryption: TKIP (Temporal Key Integrity Protocol) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. • WPA Pre-Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters.
WIRELESS ROUTER ADSL 3.8.2.4 SYSTEM There are five items under the System section: • Password • TimeZone • Upgrade • Factory Settings • Restart 3.8.2.4.1 Password Every time you change your password, please record the password and keep it at a safe place. If you ever forget the password to log in, you may press the RESET button up to 10 seconds to restore the factory default settings. (user="admin", password="Atlantis") Please note that the maximum input for password is 16 alphanumeric characters long.
WIRELESS ROUTER ADSL Do NOT upgrade firmware on any Atlantis Land product over a wireless connection. Failure of the device may result. Use only hard-wired network connections. Click Image Download. Press the Sfoglia button to specify the path of the firmware file. Then, click Upload to start upgrading. When the procedure is completed, Router will reset automatically to make the new firmware work. 3.8.2.4.
WIRELESS ROUTER ADSL 3.8.2.5 Firewall Your router includes a full DoS firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation. Please see the WAN configuration section for more details on NAT) the router acts as a “natural” Internet firewall, as all PCs on your LAN will use private IP addresses that cannot be directly accessed from the Internet.
WIRELESS ROUTER ADSL Packet filtering function enables you to configure your router to check specified internal/external user (IP address) from Internet access, or you can disable specific service request (Port number) to /from Internet. This configuration program allows you to set up different filter rules up to 10 for different users based on their IP addresses or their network Port number.
WIRELESS ROUTER ADSL 3.8.2.5.2 Bridge Filtering MAC filtering function enables you to configure your ADSL Firewall Router to block internal user (MAC address) from Internet access. ~ Enable / Disable: Check Enable / Disable radio button to active / disable, in respectively, the MAC address filter function. If you check Enable, remember to choose either Allowed or Blocked the MAC Address listed in the table, as shown above.
WIRELESS ROUTER ADSL 3.8.2.5.4 Block Wan Request The “Block WAN Request” is a stand-alone function and not relate to whether security enable or disable. Mostly it is for preventing any scan tools from WAN site by hacker. 3.8.2.5.5 URL Blocking URL filter rules allow you to prevent users on your network from accessing particular websites by their URL. There are no predefined URL filter rules; you can add filter rules to meet your requirements.
WIRELESS ROUTER ADSL For example, if the URL is http://www.atlantis-land.com/start.html, it will be dropped as the keyword “start” occurs in the URL. Domains Filtering: This function checks the domain name in URLs accessed against your list of domains to block or allow. If it is matched, the URL request will be sent (Trusted) or dropped (Forbidden). The checking procedure is: 1. Check the domain in the URL to determine if it is in the trusted list.
WIRELESS ROUTER ADSL 3.8.2.6 VPN The router supports IPSec VPN to establish secure, end-to-end private network connections over a public networking infrastructure. Click on Submit. Remote: • Remote Gateway IP: The IP address of the remote VPN device that is connected and establishes a VPN tunnel. • Remote Subnet/Network: Set the IP address, subnet or address range of the remote network. Proposal: • Proposal: Select the IPSec security method.
WIRELESS ROUTER ADSL • 3DES: Stands for Triple Data Encryption Standard, it uses 168 (56*3) bits as an encryption method. Perfect Forward Secrecy: Choose whether to enable PFS using Diffie-Hellman publickey cryptography to change encryption keys during the second phase of VPN negotiation. This function will provide better security, but extends the VPN negotiation time.
WIRELESS ROUTER ADSL 3.8.2.6.1 IPsec VPN The router supports IPSec VPN to establish secure, end-to-end private network connections over a public networking infrastructure. Model Code Picture IP NAT LAN IP Subnet Mask VPN IPSec Encryption Authentication Perfect Forward Secrety Pre Shared Key Remote LAN A02-RA3+ Office LAN A02-RA240-54G /A02-RA210-W54 69.121.1.31 Yes 192.168.1.X 255.255.255.0 ESP DES MD5 None 123456789 69.121.1.32 Yes 192.168.2.X 255.255.255.
WIRELESS ROUTER ADSL • Remote LAN(A02-RA3+): • Office LAN(A02-RA240-W54): 42
WIRELESS ROUTER ADSL 3.8.2.7 Virtual Server When you click Virtual Server, you get the following figure. Being a natural Internet firewall, this network router protects your network from being accessed by outside users. When it needs to allow outside users to access internal servers, e.g. Web server, FTP server, E-mail server or News server, this modem can act as a virtual server. You can set up a local server with specific a port number that stands for the service, e.g.
Application ICQ 98, 99a NetMeeting 2.1 a 3.
WIRELESS ROUTER ADSL 3.8.2.8 Advanced There are 9 items under the Advanced section: • ADSL • DNS • Dynamic DNS • NAT • RIP • SNMP • Static Route • Misc Configuration • Diagnostic Test 3.8.2.8.1 ADSL • Annex Mode Config: Default at User Select • User Selected Annex Mode:AnnexA. ADSL Annex A, which works over a standard telephone line. Annex B, which works over an ISDN line. • Trellis (Enable): Default at Enabled. • Handshake Protocol (Autosense G.dmt First): The default is Autosense G.
WIRELESS ROUTER ADSL 3.8.2.8.3 Dynamic DNS With Dynamic DNS service, a domain name can be translated into a dynamic IP address, which is often issued by ISP for dial-up service. A local server, such as Web server, Email server or FTP server, can then be easily accessed without knowing the changing IP address. Check the “Enable” button to access the Dynamic DNS service. You may sign up Dynamic DNS service at http://www.dyndns.org and there you can also register domain names.
WIRELESS ROUTER ADSL • NAT (Static): This option maps single WAN IP address to the local PC IP address. It is peerto-peer mapping, one-to-one. For each WAN interface, only one local PC IP address can be associated with each WAN interface. Click the link Session Name Configuration to add the session name for WAN interface. • NAPT (Static): This option maps the single WAN IP address to many local PCs IP addresses, one-tomany. It is the multiple-mapping mechanism.
WIRELESS ROUTER ADSL 3.8.2.8.5 RIP • RIP(Enable): Default at Disabled. • Supply Interval(30seconds): Time among 2 packets RIP • Expire Timeout(180seconds): Lead time before the timeout • Garbage Timeout(120 seconds) 3.8.2.8.6 SNMP Simple Network Management Protocol (SNMP) is an optional feature that may or may not be supported by your ADSL Wireless Router ADSL. SNMP is an application layer protocol that is used for managing networks.
WIRELESS ROUTER ADSL Trap Community: This is the password to access and view SNMP traps. The Trap Community can be up to 127 characters. Default is “trap community.” Trap SNMP Version: Select from Version 1 or Version 2. Default is Version 1. Trap IP: This is the IP address to which SNMP traps are sent. There can be up to 5 different SNMP trap destination IP addresses. Trap Port: This is the corresponding port for the SNMP trap (see Trap IP above) 3.8.2.8.
WIRELESS ROUTER ADSL Add: Click this button to add a new static routing. When you click this button, the next figure appears. Edit: Check the item you want to edit. Then, click the “Edit” button. Delete: Check the item you want to delete. Then, click the “Delete” button. Destination Subnet / Dest. Subnet Mask / Gateway Address: Fill in these fields required by this Static Routing function.
WIRELESS ROUTER ADSL 3.8.2.8.8 MISC CONFIGURATION There are six items under the System section: • Http Remote • FTP e TFTP • DMZ • DHCP Relay • PPP reconnect on WAN access • PPP Half Bridge Http Server Access: Default at Disabled. Or you may check it and specify the IP address or a group of IPs (subnet) allowed to access router. FTP /TFTP/Telnet: Router can act as a FTP/TFTP/Telnet server DMZ: Enable this and specify the DMZ Host IP to access any incoming request packets from WAN site.
WIRELESS ROUTER ADSL Connect PPP when ADSL is UP: Check to enable this device to automatically re-establish the PPPoE/PPPoA session whenADSL is UP. UPnP: Universal Plug and Play (UPnP) is an architecture for pervasive peer-to-peer network connectivity of PCs and intelligent devices or appliances, particularly within the home.
WIRELESS ROUTER ADSL Chapter 4 Troubleshooting If the Wireless ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save you time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the Wireless ADSL Router Problem Corrective Action None of the LEDs are on when you turn on the Wireless ADSL Router.
WIRELESS ROUTER ADSL Verify that the IP address and the subnet mask are consistent between the Wireless Router ADSL and the workstations.
WIRELESS ROUTER ADSL APPENDIX A Wireless LAN Overview This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a peer-to-peer network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN. Channel The range of radio frequencies used by IEEE 802.11b wireless devices is called a “channel”.
WIRELESS ROUTER ADSL permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within its range to notify them to defer their transmission. It also reserves and confirms with the requesting station the time frame for the requested transmission. Stations can send frames smaller than the specified RTS/CTS directly to the AP without the RTS (Request To Send)/CTS (Clear to Send) handshake.
WIRELESS ROUTER ADSL Data Encryption with WEP WEP encryption scrambles the data transmitted between the wireless stations and the access points to keep network communications private. It encrypts unicast and multicast communications in a network. Both the wireless stations and the access points must use the same WEP key for data encryption and decryption. The ADSL Router allows you to configure up to four 64-bit or 128-bit WEP keys but only one key can be enabled at any one time.
WPA-PSK TKIP WIRELESS ROUTER ADSL If you chose 128-bit WEP, then enter 13 ASCII characters or 26 hexadecimal characters ("0-9", "AF"). You must configure all four keys, but only one key can be activated at any one time. The default key is key 1. The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters.
WIRELESS ROUTER ADSL APPENDIX B Traffic Shaping Traffic Shaping is an agreement between the carrier and the subscriber to regulate the average rate and “burstiness” or fluctuation of data transmission over an ATM network. This agreement helps eliminate congestion, which is important for transmission of real time data such as audio and video connections. Peak Cell Rate (PCR) is the maximum rate at which the sender can send cells. This parameter may be lower (but not higher) than the maximum line speed.
WIRELESS ROUTER ADSL APPENDIX C Technical Features IP, NAT, ARP, ICMP, DHCP(server, relay and client), RIP1/2 , SNMP, SNTP client, UPnP, Telnet server RJ-45, 4 10/100Base-T ports (1 10/100 Base-T port on LAN port A02-RA210-W54) RJ-11 (1 port ADSL) WAN port Reset, Power On/Off External buttons Power, System, Lan (4), WLAN and ADSL LED Indicators Standard ADSL Compliance ANSI T1.413 Issue 2, ITU-T G.992.1(Full Rate DMT), ITU-T G.992.2 (Lite DMT), ITU-T G.994.
WIRELESS ROUTER ADSL APPENDIX D Support If you have any problems with the Wireless Router ADSL, please consult this manual. If you continue to have problems you should contact the dealer where you bought this ADSL Router. If you have any other questions you can contact the Atlantis Land company directly at the following address: Atlantis Land SpA Viale De Gasperi, 122 20017 Mazzo di Rho(MI) Tel: +39. 02.93906085, +39. 02.93907634(help desk) Fax: +39. 02.93906161 Email: info@atlantis-land.
