Owner’s Manual PA1001G Power Amplifier Atlas Sound PA1001G, 1-channel, 100W, 70V/100v commercial Power Amplifier Ultra Compact Design with Integrated Video Pole Mount Support System 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 –1– Specifications are subject to change without notice. AtlasSound.
PA1001G Power Amplifier Owner’s Manual TABLE OF CONTENTS Important Safety Instructions...................................................................................................................................................3 Introduction, Features, and Applications.................................................................................................................................5 Front Panel Description.................................................................................
Owner’s Manual PA1001G Power Amplifier The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION 5W neered d A ´ RISQUE DE DECHARGE ELECTRIQUE -NE PAS OUVRIR.
PA1001G Power Amplifier • • • • • • • • • • • WARNING • • WHEN THE DEVICE IS IN USE To prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to Atlas Sound. Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from the AC outlet and contact Atlas Sound.
Owner’s Manual CAUTION • • • • • • PA1001G Power Amplifier When the Product is in Use When powering the product up for the first time, ensure that the level control is turned down. Unexpected high sound pressure levels may be present at the speakers and result in hearing loss. Never place heavy objects on the product, causing it to fall and/or break, resulting in personal injury and property damage. In addition, the product itself may fall and cause injury and property damage.
PA1001G Power Amplifier Owner’s Manual 2 3 5 7 6 1 4 Front Panel 1. Power Switch This switch turns the AC Mains power to the amplifier on or off. 2. Power LED Illuminates Red when the power switch is depressed. Red means the amplifier has AC mains power to the unit and is standby or sleep mode. When LED is Blue the unit is active and will pass audio. 3.
Owner’s Manual PA1001G Power Amplifier 1 3 2 4 11 5 10 6 7 8 9 Rear Panel 1. IEC AC Receptacle Connect this grounded power cord to 100VAC - 240VAC 50/60Hz circuits only. Serious damage may result otherwise. 2. AC Mains Fuse For 100v - 240v 50Hz - 60Hz operation use Slow Blow T1.6AL 250v, 5mm x 20mm. Note: Fuse is internal and should only be changed by a qualified technician. 3.
PA1001G Power Amplifier Owner’s Manual 8. Four Position Dip Switch Assignment Switch 1 - Sense On/Off, this switch activates the PA1001G remote turn on sensing circuits via either Audio or AC trigger. When the switch is in the “DOWN” position, all trigger circuits are bypassed. The only way to turn the amp On or Off is via the mains AC Power Switch located on the front panel. When in the “UP” position either the Audio or AC Sense turn on Triggers is activated. See switch 2 for selection.
Owner’s Manual PA1001G Power Amplifier INSTALLATION and CONSIDERATIONS Cabling: The PA1001G can be used with either balanced or unbalanced sources, and the outputs can be used with either balanced or unbalanced loads, provided the proper cabling is used. A balanced line is defined as two-conductor shielded cable with the two center conductors carrying the same signal but of opposite polarity when referenced to ground.
PA1001G Power Amplifier Owner’s Manual Placement and mounting of the PA1001G Turn off all equipment before making connections. Mount amplifier in a standard-width 19” rack. It can be mounted above or below anything that does not generate excessive heat. Although the unit’s chassis is shielded against radio frequency and electromagnetic interference, extremely high fields of RF and EMI should be avoided.
Owner’s Manual PA1001G Power Amplifier Pole Mount Pre Assembly Pole Mount Final Assembly 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 – 11 – Specifications are subject to change without notice. AtlasSound.
PA1001G Power Amplifier Owner’s Manual SPECIFICATIONS Output Power 100 Watts @ 70v into 50Ω load, 100w @ 100v into 100Ω load RMS 1% THD TOTAL HARMONIC DISTORTION 0.2% FREQUENCY RESPONSE +/-3dB 30Hz - 20 KHz No Hi-Pass Filter +/-3dB 100Hz - 20KHz Hi-Pass engaged Protection Circuits AC fuse (T1.
Owner’s Manual PA1001G Power Amplifier notes: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 – 13 – Specifications are subject to change without notice. AtlasSound.
PA1001G Power Amplifier Owner’s Manual notes: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.com – 14 – Specifications are subject to change without notice.
Owner’s Manual PA1001G Power Amplifier notes: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 – 15 – Specifications are subject to change without notice. AtlasSound.
PA1001G Power Amplifier Owner’s Manual Limited Warranty All products manufactured by Atlas Sound are warranted to the original dealer/installer, industrial or commercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any.
