Kaye Wall Mounted Oscillating Fan READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz For Damp Location QUICK ASSEMBLY NOTES: * Do not wire in fan while house wires are Live. Turn power off at breaker before installation begins. * Do not use any controls, wall or remote, other than those provided by Matthews Fan Company. * Only one wall switch per fan. Must use our wall control.
TOOLS AND MATERIALS REQUIRED Philips screw driver Standard, flat-head screw driver 11 mm wrench Step ladder Wire cutters PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: a. b. c. d. e. f. g.
READ AND SAVE THESE SAFETY AND INSTALLATION INSTRUCTIONS. Consult a licensed electrician if unsure of any point below mentioned. DANGER/WARNING/CAUTION 1. WARNING: TO REDUCE THE RISKS OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. B.
9. CAUTION: to reduce the risk of injury to persons, install fan so that bottom edges of fan blades are to be: In Canada, to satisfy CSA requirements: at least 8.3 Ft/2.5 M above the floor and all objects in room. In the US, to satisfy UL requirements: at least 7.0 Ft above the floor and all objects in room. ATTENTION: Installer de sorte que les pieces inferieures soient a au moins 2.5 metres au-dessus du plancher ou du sol. 10.
MOUNTING/INSTALLLATION OF THE FAN AND MAKING THE ELECTRICAL CONNECTIONS Screws Side mount wall junction box Before touching a screw driver thoroughly read these installation instructions. Your new wall fan will require a grounded electrical supply line of 120 volts AC, 60 Hz circuit. The junction box must be securely anchored and capable of withstanding a load of at least 45 lbs. Figure 1 WARNING/CAUTION: Before installing new wall junction box turn off power at service panel. Allen wrench 1.
4. Connect the neutral fan wire to the household neutral wire. (Fig. 3) Neutral Hot Ground SUPPLY CIRCUIT 5A. Single Circuit Connection Oscillation and fan motor action are not separate. Connect the black, hot fan blade motor wire to the blue, hot oscillating motor wire. Attach these two wires to the hot, household supply wire. (Fig. 3) 6. Connect the green, fan ground wire to the household ground wire. Figure 3 7.
MOUNTING/INSTALLATION OF THE WALL CONTROL Outlet box Switch Screws Wall plate 1. Remove the existing wall plate and switch. (Fig. 5) 2. Set knobs on the new, wall control in the "0" position. 3. Make speed control wire connections (Fig. 6). Ensure that bare wires are fully inserted into their terminals with no loose strands and that terminal screws are fully tightened. Figure 5 Hot wire from fan blade motor to wall speed control port labeled "Fan." Hot black/white household supply Blue/Hot to OSC.
OPERATING THE WALL CONTROL Restore Power to Wall Fan. The fan 3-speed control knob is used to control the fan blade speed as follows: 0= Turns the fan off 1= High Speed 2= Medium Speed 3= Low Speed B. ON-OFF Button: This button is used to regulate the oscillating operation. Figure 8 CARE OF AND TROUBLESHOOTING YOUR FAN 1. Check hardware bi-yearly. Because of the fan's natural movement some connections may become loose over time. Check the support connections, brackets and blade attachments twice a year.
LIMITED LIFETIME WARRANTY MATTHEWS-GERBAR, LTD. DBA MATTHEWS FAN COMPANY LIFETIME LIMITED WARRANTY. warranted by Matthews-Gerbar, Ltd. to the original user against defects in workmanship or materials under normal use and inside or outside damp location installation for: Motors: Lifetime of original purchaser: Labor & Component parts: (lights, finish, blades, etc…): one year after date of purchase, Light Bulbs: no warranty. Any part, which is determined by Matthews-Gerbar, Ltd.
