Owner's Manual

MITEK CORP. © 2014
(preliminary)
1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: [phone]
FAX [phone]
AtlasSound.com
3/3
©2014 Atlas Sound L.P. All rights reserved. Atlas Sound and Strategy Series are trademarks of Atlas Sound L.P. All other trademarks are the property of their respective owners. ATS004923 RevA 6/14
Architect and Engineer Specifications
The mixer/amplifier shall control and mix up to six input signals and
deliver an audio output of 400 Watts into 41, 25V, and 70.7V. The
amplifier output shall be transformer isolated with a frequency response
50Hz – 15kHz (-3dB) with less than 0.5% THD at rated output. It shall
be capable of operation at 120VAC 60Hz line. The mixer/amplifier shall
be convection cooled. The amplifier shall have thermal and short circuit
protection.
The mixer/amplifier shall have four switch-selectable MIC/TEL balanced
inputs to accept either low impedance microphone or Tel/Line Level
signals with -60/-10dBV sensitivity. The MIC/TEL input shall include a
Phoenix (Euro Block) type connector. The MIC/TEL input impedance
shall be 6001. On Input 1, the MIC/TEL input shall include an auto mute
(VOX Mute) sensitivity control for Input 1. The MUTE SENSE control will
allow threshold adjustment of mute activation. The mixer/amplifier shall
also include an input with a summed stereo 3.5mm input and balanced
Phoenix type connector. The mixer/amplifier shall include two stereo
summing auxiliary inputs, unbalanced, -10dBv, with dual-RCA jacks. The
auxiliary input impedance shall each be 10k1. The mixer/amplifier shall
include one Zone 2 output, a transformer isolated 6001 output with a
maximum level of 1.0VRMS. The mixer/amplifier Zone 2 output shall
be assignable from Input 1, 2, 3 or 4 via the rear panel dip switch. The
Zone 2 output shall have one rear panel mounted rotary level control.
The mixer/amplifier shall incorporate rear panel terminals via Phoenix
connector for the REMOTE MUTE function, controlled by an external
switch closure. A rear panel dip switch shall allow assignment of Input
2, 3, 4, 5, and/or 6 to respond to the mute function activation. The Mute
assignment shall not affect the Zone 2 output.
The mixer/amplifier shall have a Pre-Out RCA unbalanced output. The
mixer/amplifier shall have a Power Amp input for use with an external
signal processor. The mixer/amplifier shall include the Push Here
Diagnostic system test circuitry. This test will allow for automatic testing
of the connected speaker lines for wiring and impedance errors. The
mixer/amplifier shall include Phoenix connectors for both Remote Level
Control and Remote Input Selection, which can be activated using the
rear panel DIP switches. The Remote Input Selection circuitry shall work
with Atlas Sound wall plate WPD-RISRL and allow Inputs 4, 5, and 6 or
the Master Level only to be remotely connected, selected, and adjusted
from the wall plate. The AA400PHD front panel shall include Inputs
1, 2, 3, 4, 5, and 6 level controls as well as a Master Level control
adjustment. System Signal, Peak, Limit, and Power LEDs shall also
be incorporated. The mixer/amplifier rear panel shall also include bass
and treble tone controls (100Hz and 10kHz, ±10dB). The tone controls
shall not affect the Zone 2 output. The mixer/amplifier front panel shall
include an AC Mains power switch.
Dimensions (W x H x D) shall be 16.54" x 3.66" x 14.6" (420mm x 93mm
x 422mm) with feet or 3.48" (88.4mm) H without feet. Front panel finish
and material shall be black ABS resin and case finish (and material) shall
be black painted sheet steel.