PA1001G Owner’s Manual Power Amplifier PA1001G 1-Channel 100W, 70V/100V Commercial Power Amplifier Ultra Compact Design with Integrated Video Pole Mount Support System 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 –1– Specifications are subject to change without notice. AtlasSound.
PA1001G Owner’s Manual Power Amplifier Table of Contents Important Safety Instructions .................................................................................................................. 3 Introduction ............................................................................................................................................ 5 Key Features ........................................................................................................................................
PA1001G Owner’s Manual Power Amplifier Important Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PA1001G Owner’s Manual Power Amplifier WARNING When The Device Is In Use • • • • • • • • • • To prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to Atlas Sound. Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from the AC outlet and contact Atlas Sound.
PA1001G Owner’s Manual Power Amplifier Introduction Thank for purchasing the Atlas Sound PA1001G amplifier. This new and innovative professional grade product has been designed from the ground up to include the important features that professional installation personnel require to meet or exceed their customer’s expectations.
PA1001G Owner’s Manual Power Amplifier Front Panel 3 5 7 4 2 1 6 1. Power Switch This switch turns the AC Mains power to the amplifier on or off. 2. Power Indicator This LED illuminates Red when the power switch is depressed. Red means the amplifier has AC mains power to the unit and is standby or sleep mode. When LED is Blue the unit is active and will pass audio. 3.
PA1001G Owner’s Manual Power Amplifier Rear Panel 3 2 1 5 4 10 6 11 7 8 9 1. IEC AC Receptacle Connect this grounded power cord to 100VAC - 240VAC 50/60Hz circuits only. Serious damage may result otherwise. 2. AC Mains Fuse For 100v - 240v 50Hz - 60Hz operation use Slow Blow T1.6AL 250v, 5mm x 20mm. Note: Fuse is internal and should only be changed by a qualified technician. 3.
PA1001G Owner’s Manual Power Amplifier Rear Panel 8. Four Position Dip Switch Setting • DP SW #1 - Sense On / Off - This switch activates the PA1001G remote turn on sensing circuits via either Audio or AC trigger. When the switch is in the “DOWN” position, all trigger circuits are bypassed. The only way to turn the amp On or Off is via the mains AC Power Switch located on the front panel. When in the “UP” position either the Audio or AC Sense turn on Triggers is activated. See switch 2 for selection.
PA1001G Owner’s Manual Power Amplifier Installations and Considerations Cabling: The PA1001G can be used with either balanced or unbalanced sources, and the outputs can be used with either balanced or unbalanced loads, provided the proper cabling is used. A balanced line is defined as two-conductor shielded cable with the two center conductors carrying the same signal but of opposite polarity when referenced to ground.
PA1001G Owner’s Manual Power Amplifier Placement and mounting of the PA1001G Turn off all equipment before making connections. Mount amplifier in a standard-width 19" rack. It can be mounted above or below anything that does not generate excessive heat. Although the unit’s chassis is shielded against radio frequency and electromagnetic interference, extremely high fields of RF and EMI should be avoided.
PA1001G Owner’s Manual Power Amplifier Pole Mount Pre Assembly Pole Mount Final Assembly 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 – 11 – Specifications are subject to change without notice. AtlasSound.
PA1001G Owner’s Manual Power Amplifier PA1001G Specifications Type Power Amplifier Safety Listings TUV UL60065 Standard, CE, Class 3 Rated Electrical Specifications Power Output 100 Watts @ 70v into 501 Load, 100 Watts @ 100v into 1001 Load RMS 1% THD Front Panel Power Switch Push Type Indicators Limit, Signal, Power Controls Gain, Treble, Bass Technical Data Frequency Response +/-3dB 30Hz - 20 KHz Hi-Pass Filter Not Engaged +/-3dB 100Hz - 20KHz Hi-Pass Filter Engaged Thd+N Input Sensitivity
PA1001G Owner’s Manual Power Amplifier Notes: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 – 13 – Specifications are subject to change without notice. AtlasSound.
PA1001G Owner’s Manual Power Amplifier Notes: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.
PA1001G Owner’s Manual Power Amplifier Notes: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 – 15 – Specifications are subject to change without notice. AtlasSound.
PA1001G Owner’s Manual Power Amplifier Limited Warranty All products manufactured by Atlas Sound are warranted to the original dealer/installer, industrial or commercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any.
PA1001G 70.7V 100 Watt Pole Mount Amplifier Applications ©2009 Atlas Sound L.P. All rights reserved. Atlas Sound and Strategy Series are trademarks of Atlas Sound L.P. All other trademarks are the property of their respective owners.
©2009 Atlas Sound L.P. All rights reserved. Atlas Sound and Strategy Series are trademarks of Atlas Sound L.P. All other trademarks are the property of their respective owners.
