1 WARNING'' Use only BLUE colored ports when connecting HDBaseT PoE devices.
Installation Guide AT-HDR-EX-70C-KIT 4K HDR HDMI Over HDBaseT TX/RX Kit AT-HDR-EX-70C-KIT The Atlona AT-HDR-EX-70C-KIT is an HDBaseT transmitter/receiver kit for high dynamic range (HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18 Gbps.
Installation Guide AT-HDR-EX-70C-KIT Panel Descriptions 1 2 3 1. LINK 2. FW 3. TEST 4. 5V LOCK TEST - UTILITY 9 10 AT-HDR-EX-70C-TX AT-HDR-EX-70C-RX POWER POWER LINK FW LINK + RX TX DC 48V 4 RS-232 5 S IR IN S IR OUT 6 RX TX HDBaseT OUT HDMI IN RS-232 7 8 11 P S IR IN S IR OUT 12 HDBaseT IN 13 HDMI OUT 14 1 TEST Quick and easy test for cables. Use the button to start the test and the LED to determine pass or fail.
Installation Guide AT-HDR-EX-70C-KIT RS-232 A 3-pin captive screw connector for RS-232 has been included. GND RX TX RX TX GND Pin out will be determined by the RS-232 cable and connect as RX (receive), TX (transmit) and (Ground). IR Two captive screw connectors for IR have been included. A 4-pin connector for the transmitter and a 3-pin connector for the receiver. GND S IR IN P IR IN is connected by a ground and signal wire. Use with 3rd party control systems.
Installation Guide AT-HDR-EX-70C-KIT 4. Mount the unit using the oval-shaped holes, on each mounting bracket. If using a drywall surface, a #6 drywall screw is recommended. -RX 0C X-7 R-E HD AT- WER PO K LIN FW NOTE: Mounting brackets can also be inverted to mount the unit under a table or other flat surface. Installation 1. Connect an HDR source to the HDMI IN port on the transmitter. 2. Connect an HDR display to the HDMI OUT port on the receiver. 3.
Installation Guide AT-HDR-EX-70C-KIT Connection Diagram Automation Control System 3 HDR UHD/HD Display 4 NO GND NC SIG COM +12V NO GND NC SIG COM +12V NO GND NC SIG COM +12V GND NO SIG NC +12V COM 2 1 RNET ETHE L AL DIGITOUT COAX IN R AUDIO T ONEN OUT COMP AUDIO HDMI OUT VIDEO L1 5 SERIA 3 6 1 2 IR 48V L2 SERIA 4 ORY FACT RESET OUT DC 2 Co ntr ol AT-JUNO-451 Vid Co ntr ol 51 O-4 JUN AT- DC S AT-HDR-EX-70C-RX 5V TX RX LAN 232 L eo IR IN RS- ICA OPT I I
Installation Guide AT-HDR-EX-70C-KIT UTILITY AT-HD The utility port and dial are used for updating firmware and 5V lock. Use the Dial to switch between modes. POWE 1. LINK 2. FW 3. TEST 4. 5V LOCK TEST Mode 1: Link UTILITY LINK This is the default position of the dial and puts the unit into normal operation. + - Mode 2: FW RX TX S S This mode sets the transmitter into firmware updating mode. View Firmware Updating instructions on the next page for manual updating.
Installation Guide AT-HDR-EX-70C-KIT Updating Firmware 1. Download the firmware .zip file from the firmware tab located at http://www.atlona.com/ AT-HDR-EX-70C-KIT. 2. Extract the firmware, from the archive file, to the Windows desktop or other folder. 3. Make sure the included 48 V DC power supply is connected to the transmitter and that an Ethernet cable is connected between the HDBaseT OUT and HDBaseT IN ports on the transmitter and receiver, respectively. Transmitter only: a.
Installation Guide AT-HDR-EX-70C-KIT Version 4 Toll free US International atlona.com • 877.536.3976 • 41.43.508.4321 © 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice. Actual products, product images, and online product images may vary from images shown here.
@ ATL □ NA . Atlona IR Emitter Cable for POE Extenders AT-JR-CS-TX atlona.
~ ATLONA . Placement The IR emitter can be used in several positions around the controlled device. As long as the IR receiving window is lined up with the emitted IR signal . (See pictures below for possible placement options) A red LED will flash to indicate the IR emitter is operational and transmitting.
4K HDR HDMI over HDBaseT™ TX/RX with Control and PoE Introduction The Atlona AT-HDR-EX-70C-KIT is an HDBaseT transmitter/receiver kit for high dynamic range (HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18 Gbps.
4K HDR HDMI over HDBaseT™ TX/RX with Control and PoE Key Features 4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats • Compatibility with new and emerging 4K/UHD and HDR-capable sources and displays. • Compatible with 4K HDR10 @ 60 Hz and Dolby® Vision™ @ 30 Hz • Fully supports video resolutions, audio formats, and color space formats in the HDMI 2.0b specification. HDCP 2.2 compliant • Adheres to latest specification for High-bandwidth Digital Content Protection.
4K HDR HDMI over HDBaseT™ TX/RX with Control and PoE Connection Diagram Automation Control System UHD Display 4 NO GND NC SIG COM +12V NO GND NC SIG COM +12V NO GND NC SIG COM +12V GND NO SIG NC +12V COM 3 2 1 ET ERN ETH L ITAL DIGX OUT COA R ENT PON IO COM IO IN AUD OUT AUD I HDM O OUT VIDE IAL 3 IAL 6 1 Y 2 SER 4 TOR FAC ET RES 2 IR 48V 1 SER 5 OUT DC 2 Co ntr ol AT-JUNO-451 Vid Co ntr ol -451 NO AT-JU DC S RX TX eo AT-HDR-EX-70C-RX 5V N LA 2 -23
4K HDR HDMI over HDBaseT™ TX/RX with Control and PoE Specifications Video UHD/HD/SD 4096×2160@24/25/30/50/60Hz, 3840×2160@24/25/30/50/60Hz, 2048x1080p, 1080p@23.98/24/25/29. 97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@50/59.
~TLCJN~ e Connecting Tech nology Did you know, many questions can be answered using our online technical support website and internal knowledge database? Technical Support website: www.atlona.com/tech-support U.S. Technical Support Hours: U.S. Technical Support Phone Numbers: Monday-Friday: 5am - 5pm (PST) Weekends and Holidays: 7am - 4pm (PST) Chat available from: 5am - 5pm {PST) weekdays only Toll Free: +1 (877) 536-3976 International: +1 (408) 962-0515 ext.