Product Datasheet/Brochure

Two-Input Wall Plate Switcher for HDMI
and VGA Inputs with HDBaseT Output
AT-HDVS-150-TX-WP
atlona.com
70 Daggett Road, San Jose, CA 95134
tel: [phone], toll free: 1-877-536-3976, fax: [phone]
©Atlona 2003-2015
The Atlona AT-HDVS-150-TX-WP is a 2×1 wall plate switcher with display control for HDMI and VGA transmission
over HDBaseT™. It features an HDMI input plus VGA input with 3.5mm audio connector on a two-gang, US or UK
wall plate. Plates without buttons are also available (AT-HDVS-TX-WP-NB). Designed as a remote input device for
the AT-UHD-CLSO-824 matrix switcher, the AT-HDVS-150-TX-WP combines the benefits of a switcher with built-in
auto-switching and the advantages of long-distance HDBaseT signal extension over a single cable. Video signals up to
1080p/60Hz with embedded audio, VGA input signals up to 1920×1200 video, and control signals can be extended
up to 230 feet (70 meters). The switcher enables auto display on/off, auto-switching, along with other features. The
switcher is receives power from the AT-UHD-CLSO-824 using Power over Ethernet. The AT-HDVS-150-TX fits inside
any 40 mm deep two-gang electrical box or mud ring and is ideal for long distance transmission and display control in
corporate or educational settings using analog and digital sources.
The Atlona AT-HDVS-150-TX-WP switcher expands the input capabilities of the AT-UHD-CLSO-824. Each remote
switcher provides input access for up to two devices with controls for input selection and can control display power
state when used with a third party control system. The HDVS series is designed to smooth the transition from analog
to digital displays, allowing advanced HDMI display devices to be used with legacy VGA sources. The series also
adds the simplicity and performance of HDBaseT technology to eliminate multiple cable runs and signal degradation
that can occur with long transmission lines. Cost-effective and easy-to-terminate category cable provides additional
integration benefits.
US or UK, two-gang wall plate -
• Shallow, 1.5 in (35 mm) deep wall plate simplifies
integration with a recessed RJ45 connector
• Attractive alternative to table top boxes for
placement near presenter’s station
2×1 HDBaseT™ switcher transmitter -
• Features an HDMI input plus VGA input with 3.5mm
audio connector
• Allows advanced HDMI display devices to be used
with legacy VGA sources
Long distance HDMI extension -
• Transmits HDMI and VGA/Audio signals up to 230
ft (70m) @ 1080p over CAT6a/7 and 197 feet (60 m)
@1080p over CAT5e/6
• Uses easy-to-integrate category cable for low-cost,
reliable system installation
Auto-switching -
• Selects active input when sources are connected or if
there is a change in source power status
• Eliminates need for complex control system in small
AV systems
Front panel Input Select button -
• Overrides auto-switching when two active sources
are present
• Simple manual control allows presenter to maintain
control of AV system
Auto display control -
• Automatically changes projector power state based
on active or standby mode of scaler. Control signals
transmitted via RS-232.
• Eliminates need for complex control system in small
AV systems. Enables display control with
AT-UHD-CLSO-824.
Front panel Display On/Off control -
• Remotely controls display power state; provides
alternate ‘Display Mute’ mode
• Eliminates need for manual operation of display or
use of IR remote control
Optional “No Button” US faceplate -
• Input control from third-party switcher only
• Allows the presenter to control the meeting