4K/UHD 6x2 Matrix Switcher for HDMI, USB-C, and HDBaseT with USB AT-OME-PS62 Atlona Manuals Switchers
Version Information Version Release Date Notes 1 June 2019 Release AT-OME-PS62 2
Welcome to Atlona! Thank you for purchasing this Atlona product. We hope you enjoy it and will take a extra few moments to register your new purchase. Registration only takes a few minutes and protects this product against theft or loss. In addition, you will receive notifications of product updates and firmware. Atlona product registration is voluntary and failure to register will not affect the product warranty. To register your product, go to http://www.atlona.
Atlona, Inc. (“Atlona”) Limited Product Warranty Coverage Atlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service.
Atlona, Inc. (“Atlona”) Limited Product Warranty • Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product.
Important Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCT THE RISK OF ELECTRIC SHOCK DO NOT OPEN ENCLOSURE OR EXPOSE TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product.
Table of Contents Introduction 8 Features 8 Package Contents 8 Panel Description 9 Installation Captive Screw Connections Mounting Instructions Connection Instructions IP Modes Connection Diagram 10 10 11 13 13 14 WebGUI I/O Settings Audio Display RS-232 EDID Config System 15 16 18 20 22 23 24 25 Appendix Specifications 27 27 AT-OME-PS62 7
Introduction The Atlona AT-OME-PS62 is a 6x2 matrix switcher with HDMI, USB-C, and HDBaseT inputs, plus HDMI and HDBaseT outputs. Part of the Omega™ Series of integration products for modern AV communications and collaboration, the OME-PS62 features HDBaseT extension for video up to 4K/60 4:2:0, plus embedded audio, control, Ethernet, and USB over distances up to 330 feet (100 meters). The HDMI and USB-C ports support video up to UHD/60 4:4:4. The OME-PS62 is HDCP 2.
Panel Description 1 OMEGA TM PRESENTATION SWITCHER 3 4 5 LINE IN MIC AT-OME-PS62 1 L R L 2 R L AUDIO OUT L R 1 MENU 1 2 3 ENTER 4 5 6 7 6 AUDIO IN 2 2 R RS-232 8 9 IP MODE 48V MIC LINE RESET RX TX 1 HDBaseT IN 10 1 2 3 4 HDMI IN 5 12 6 USB-C IN USB HUB 11 13 Function Buttons MENU - Access the front panel menu or use as a back button within the menu. The menu can be used to route inputs, change audio and EDID settings, and view device information.
Installation Captive Screw Connections RS-232 A 3-pin captive screw connector has been included for RS-232. GND RX TX RX TX GND Pin out will be determined by the RS-232 cable and connect as RX (receive), TX (transmit) and (Ground). Ground will be shared between port 1 and port 2. Audio Connect to an audio DSP, amplifier, or other audio distribution devices.
Installation Mounting Instructions The AT-OME-PS62 can be mounted in a standard 19-inch rack or placed freestanding on top of a desk or table. Rack Installation 1. Remove the front two case screws from the sides of the case. 2. Attach the included rack ears to each side of the AT-OME-PS62 using the case screws.
Installation Surface Mounting The AT-OME-PS62 can be placed freestanding on top of a desk, a table, or in a cabinet. To prevent damage to the surfaces or unnecessary movement of the matrix, four feet have been included. 1. Turn the unit upside down. 2. Install each foot using the included feet screws, the rubber grips of the feet should be facing up during installation. 3. Turn the unit right-side up and place it in the desired location.
Installation Connection Instructions 1. Connect compatible HDBaseT transmitters (e.g. AT-OME-EX-TX) to the HDBaseT input ports. 2. Connect HDMI and USB-C sources to the HDMI and USB-C input ports. 3. *Optional* Connect 2CH sources to the analog AUDIO IN ports. 4. *Optional* Connect a MIC or line input to the MIC/LINE input port and use the dip switch to ensure the port is in the correct mode. 5.
X-W P X A X-T ud io TX Ba HD MI HD IN T se T OU t AES P pac DS Com DSP sor ces Pro T io Au d se Ba HD Document Camera seT 62 -PS -OME AT 1 eT Bas HD IN 2 HD 5 MIC 6 IN -C USB 48V LINE MI E IN LIN MIC 4 IN MI HD B US 3 B HU L 1 R ST HO 1 DIO USB AU Laptop USB 2 IN L FIER AMPLI 2 R 1 1 2 R 2 C B- T TPU T OU L OU R HE ITC N SW TIO TA SEN PRE DIO TM AU R US L A EG OM 232 TX RS- RX DE E
WebGUI The AT-OME-PS62 includes a built-in webGUI, which allows easy remote management and control of all features. Follow the instructions below to access the webGUI. 1. 2. 3. 4. 5. Make sure that an Ethernet cable is connected between the LAN port on the AT-OME-PS62 and the network. Use an IP scanner to determine the IP address of the unit. Launch a web browser and enter the IP address in the address bar. The AT-OME-PS62 Login page will be displayed. Enter the following information on the Login page.
webGUI I/O Settings Select I/O Settings from the top navigation to adjust routing and video settings. Output Matrix Mode - When enabled, the outputs will switch independently. When disabled (default), the outputs will mirror each other. Auto Switch - When enabled, the input will switch to the most recently plugged in. This is only available when Matrix mode is disabled. Input Selection - Manually route ports. Only one port will be switchable when matrix mode is disabled.
webGUI HDMI Output Scaler Scaler - When enabled, will display extra options. This is for the HDMI output only. Resolution - Select the output resolution the source signal will be scaled to from the drop down menu.
webGUI Audio Select Audio from the top navigation to adjust output levels and MIC options. Audio Output 1 & 2 configuration Source - Select between HDMI Output, HDBaseT Output, Aux 1 (AUDIO IN 1), Aux 2 (AUDIO IN 2), and Aux 3 (LINE IN) to. Ducking - Enable ducking to have the source audio adjust when receiving active MIC input. Attack Time - Set the delay before ducking beignas after detecting signal from a microphone. Release Time - Sets the delay time after no signal is detected that ducking stops.
webGUI Master Volume Output 1 & 2 - Adjusts the output volume for the HDMI and HDBaseT outputs. Default is 0dB and can be adjusted from -90dB to 10dB. Input Volume Level Adjustment - Adjusts the input volume for each individual audio source. Default is 0dB and can be adjusted from -90dB to 10dB. EQ Output 1 & 2 Band level - Use the slider to adjust each individual band of the output volume. Default is 0dB and can be adjusted from -12dB to 12dB.
webGUI Display Select Display from the top navigation to adjust display control settings. NOTE: The Display page is only available when Matrix mode is disabled. CEC Command HDBaseT and HDMI Power - Using CEC protocol, the PS62 will send the on and off commands out the HDMI outputs of the PS62 and compatible HDBaseT receiver. Volume - Pressing these buttons will send the CEC commands for volume up, down, and mute, out the HDMI outputs of the PS62 and compatible HDBaseT receiver.
webGUI TCP/IP Settings of Controlled Device (only available when IP is selected) IP Mode - Toggle telnet login mode between Non-Login and Login. If set to Login, a username and password will be required to control the controlled device via TCP/IP. IP Address - Sets to the IP of the controlled device/display. Telnet Port - Set the telnet port of the controlled device for control. Default is 23. Username & Password - Sets the username and password that is required when login mode is enabled.
webGUI RS-232 Select RS-232 from the top navigation to adjust the parameters of the RS-232 ports. RS-232 Parameter Setting Console - Select the baud rate, data bit, parity, and stop bit to match the control system’s parameters. Defaults are 115200, 8, None, and 1. HDBaseT In 1 - Select the baud rate, data bit, parity, and stop bit that will be sent from the HDBaseT IN port to the connected HDBaseT transmitter. This should be set to match the source device being controlled by the transmitter.
webGUI EDID Select EDID from the top navigation to save/load EDIDs. EDID EDID Settings - Use the drop down menu to select from default (highest common resolution between source and display), 12 internal EDIDs, and previously saved EDIDs. EDID Saved - The ID field will display the memory # and currently saved EDID name, select the output from the drop down menu to be saved. Once the output is selected, press the save button to make it available in the EDID settings drop down menus.
webGUI Config Select Config from the top navigation to change the user password. Users Admin Password - Update the admin password for the switcher. Only the admin password may be changed, the username will remain admin. NOTE: The passwords cannot contain any special characters. e.g. !@#$%/^&*\?+-;’”. Once the new password has been entered, press the Save button to make the password live. The user will be logged out and must log back in with the new password.
webGUI System Select System from the top navigation to adjust network, USB, and general system options. Network MAC Address - Displays the MAC address of the unit. IP Mode - Switch between static and DHCP IP modes. IP, Netmask, Gateway - This will display the unit’s current DHCP IP settings. When set to static, fill in the IP address, netmask, and gateway. Telnet Port - Set the telnet port if needed for control. Default port is 23. Telnet Login Mode - Toggle telnet login mode on and off.
webGUI System Power - Toggle the SW32 between on and standby (off) mode. Lock - Lock or unlock the front panel buttons. Reset to Default- Press the Factory Default button to set the unit back to all factory settings, including IP mode. Firmware update - Use the choose file button to search the local PC for the firmware file. Once selected, press the update button to start the firmware update. NOTE: Firmware updates and release notes can be found at https://atlona.com/product/AT-OME-SW32/ .
Appendix Specifications Video HDMI 2.0 (1.4 when downscaled) HDCP 2.2 / 1.4 UHD/HD/SD 4096x2160@60(1)/50/30/25/24Hz, 3840×2160@60(1)/50/30/25/24Hz, 1080p@60/59.9/50/30/29.97/25/2 4/23.98Hz, 1080i@30/29.97/25Hz, 720p@60/59.94/50Hz, 576p@50Hz, 576i@25Hz, 480p@60/59.
Appendix Resolution / Distance 4K/UHD - Feet / Meters 1080p - Feet / Meters HDMI IN/OUT 15 5 30 10 CAT5e 295 90 330 100 CAT6/6a/7 330 100 330 100 Connectors, Controls, and Indicators HDMI IN 3 - Type A, 19-pin female HDBaseT IN 2 - RJ45, female USB-C IN 1 - USB Type-C v3.
Toll free US International atlona.com • 877.536.3976 • 41.43.508.4321 © 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice. Actual products, product images, and online product images may vary from images shown here.