User Manual

Specifications
ZigBit™ 2.4 GHz Amplified Wireless Modules 3-12
8228B–MCU Wireless–06/09
Notes: 1. The UART_TXD pin is intended for input (i.e. its designation as "TXD" implies some complex system
containing ZigBit Amp as its RF terminal unit), while UART_RXD pin, vice versa is for output.
2. Most of pins can be configured for general purpose I/O or for some alternate functions as described in
details in the ATmega1281V Datasheet [3].
3. GPIO pins can be programmed either for output, or for input with/without pull-up resistors. Output pin
drivers are strong enough to drive LED displays directly (refer to figures on pages 387-388, [3]).
4. All digital pins are provided with protection diodes to D_VCC and DGND
5. It is strongly recommended to avoid assigning an alternate function for OSC32K_OUT pin because it is
used by BitCloud. However, this signal can be used if another peripheral or host processor requires
32.768 kHz clock, otherwise this pin can be disconnected.
6. Normally, JTAG_TMS, JTAG_TDI, JTAG_TDO, JTAG_TCK pins are used for on-chip debugging and
flash burning. They can be used for A/D conversion if JTAGEN fuse is disabled.
7. The following pins can be configured with the BitCloud software to be general-purpose I/O lines:
GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, GPIO7, GPIO8, GPIO_1WR, I2C_CLK, I2C_DATA,
UART_TXD, UART_RXD, UART_RTS, UART_CTS, ADC_INPUT_3, ADC_INPUT_2, ADC_INPUT_1,
BAT, UART_DTR, USART0_RXD, USART0_TXD, USART0_EXTCLK, IRQ_7, IRQ_6. Additionally, four
JTAG lines can be programmed with software as GPIO as well, but this requires changing the fuse bits
and will disable JTAG debugging.
8. With BitCloud, CTS pin can be configured to indicate sleep/active condition of the module thus provid-
ing mechanism for power management of host processor. If this function is necessary, connection of
this pin to external pull-down resistor is recommended to prevent the undesirable transients during
module reset process.
35 AGND Analog ground
36 GPIO9/1_WR
General Purpose digital input/output 9 /
1-wire interface
(2)(3)(4)(7)
I/O
37 UART_DTR
DTR input (Data Terminal Ready) for UART.
Active low
(2)(3)(4)(7)
I tri-state
38 USART0_RXD USART/SPI Receive pin
(2)(3)(4)(7)
I tri-state
39 USART0_TXD USART /SPI Transmit pin
(2)(3)(4)(7)
O tri-state
40 USART0_EXTCLK USART/SPI External Clock
(2)(3)(4)(7)(11)
I/O tri-state
41 GPIO8 General Purpose Digital Input/Output I/O tri-state
42 IRQ_7 Digital Input Interrupt request 7
(2)(3)(4)(7)
I tri-state
43 IRQ_6 Digital Input Interrupt request 6
(2)(3)(4)(7)
I tri-state
44,45,51,52,
53,56,57
DGND Digital ground
46,47 VRR Receiver supply voltage
(9)
48,50 RF GND RF Analog Ground
(2)(3)(4)(7)
49 RFP_IO Differential RF Input/Output
(10)
I/O
54,55 VTT Transmitter supply voltage
(9)
Table 3-6. Pin descriptions
Connector
Pin Pin Name Description I/O
Default
State after
Power on
01/12