Instructions / Assembly

ManualsBrandsATMOR ManualsPlumbing ProductSuper 900 Series 8.5 kW/240-Volt Tankless Electric Instant Water Heater

Directions of Assembly and Operation of “In-Line” Instant Water Heater

“Instant” appliance is a novel device designed to supply hot water instantaneously upon

demand while conserving electricity, water and energy.

The “In-Line” is the most advanced heater in the “Instant” family and as such can be installed

anywhere, and serve any purpose. When the ow switch turns on the electrical current, the

heating element heats only the amount of water economically needed for use.

900 Series

Hot Water on Demand

InLine

Summary of content (8 pages)

PAGE 1
Hot Water on Demand InLine 900 Series Directions of Assembly and Operation of “In-Line” Instant Water Heater “Instant” appliance is a novel device designed to supply hot water instantaneously upon demand while conserving electricity, water and energy. The “In-Line” is the most advanced heater in the “Instant” family and as such can be installed anywhere, and serve any purpose.
PAGE 2
OVERVIEW This manual must be read carefully before attempting to install the water heater. If you do not follow the safety rules or the instructions outlined in this manual, the unit may not operate properly and it could cause property damage, serious bodily injury or death. Atmor will not be liable for any damages because of failure to comply with the installation and operating instructions outlined in this manual or because of improper use.
PAGE 3
INSTALLATION INSTRUCTIONS This water heater must be installed by a licensed electrician, as required by law. 1. Open the four screws located on the top and bottom of the device and remove the cover from base. 2. Fix the base horizontally against a wall or side of cabinet, metal plate supplied must be installed below cable entry on the wall and ground wire must be connected to the unit, the water entry and exit connectors are on the down/bottom side of the unit. Use 4 mounting screws provided. 3.
PAGE 4
OPERATION INSTRUCTIONS 1. Your new Instant Water Heater is flow activated. Simply place one or both switches in the ON position and turn on the hot water tap. You will need to allow at least 1.5 liters per minute to flow through the unit in order to activate the Instant Heating System. Run water through the heater for a few minutes. 2. Be sure to every so often clean the spray head of sediment to assure a smooth water flow. 3. Be sure to every so often clean the incoming water filter. 4.
PAGE 5
Device with 220V-240V 10.6kW- 13kW output 3 A. A separate electrical line is needed as power supply for this device. B. The device must be connected to a separate circuit breaker. C. The recommanded electrical cable for feeding the device, see table I. 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 6
TECHNICAL INFORMATION item no. Phase Voltage Wattage (KW) Amperage Circuit breaker size Required wire size (min) Minimum water flow to activate unit Weight (lb) Dimensions (in) (HxWxD) Nominal water volume Working pressure Texted to pressure Water connections AT900-04 1 240 3.8 16 20 12 AWG AT900-06 1 240 6.5 27 30 10 AWG AT900-08 1 240 8.5 36 40 6 AWG AT900-10 1 240 10.5 44 50 6 AWG AT900-13 1 240 13 55 55 4 AWG AT900-03 1 110 3 27 30 10 AWG 0.5 GPM 0.5 GPM 0.5 GPM 0.5 GPM 0.5 GPM 0.5 GPM 3.
PAGE 7
TROUBLESHOOTING GUIDE Your water heater has no internal user serviceable parts and should be returned to the factory for repair or replacement. Please contact toll - free hot line for return authorization. If after following the Installation Instructions, your Instant heater does not heat water in accordance with this literature, please check the following: Symptom Possible Cause Solutions No hot water despite fully open hot water faucet No electrical power.
PAGE 8
LIMITED WARRANTY Atmor warrants to the original owner that our instant water heaters will be free from defects in workmanship and material for a period of TWO YEARS from the date of purchase, and free from leakage for a period of SEVEN YEARS from the date of purchase. Should any part(s) prove to be defective during this period, Atmor will be responsible for replacement of the defective part(s) only. Atmor is not responsible for labor charges or any incidental or consequential expenses.