Hot Water on Demand Installation and Operation Guide Thermo Boost Instant Water Heater Digital electric tankless instant water heater provides endless supply of hot water while significantly conserving energy and water www.atmorusa.com P.N.
Table of Contents Page Safety Guidelines...........................................................................................................................2 Technical Information......................................................................................................................3 Plumbing..................................................................................................................................... 4-5 Mounting....................................................
Important Safety Guidelines 1. Safety Guidelines Read this manual thoroughly before attempting to install the instant water heater. Failure to follow the safety instructions in this manual may cause damage to the unit, and could also result in property damage, personal injury, or loss of life. Failure to comply with the safety, installation or operating instructions voids the product warranty.
Technical Information Electrical Specifications Thermo Boost 10.5 kW 2 10,500 W 10.5 kW 240 V 50 A double-pole 43.7 A 6 AWG Heating elements Watts Kilowatts Voltage Circuit breaker amperage Breaker/relay Total connection load Cable size (minimum) Thermo Boost 14 kW 2 14,000 W 14 kW 240 V 70 A double-pole 58 A 4 AWG Plumbing Specifications Minimum water flow to activate unit Working pressure Tested pressure Water connections 0.5 gpm 7–115 psi (0.
Plumbing 01 The plumbing installation must be completed before the electrical installation. 03 05 06 08 02 A pressure relief device (PRD) must be installed on the heater’s incoming water supply line prior to installing the unit. The maximum recommended operating water pressure is 116 psi (8 bar). Residential plumbing systems with unstable pressure or pressure above 5 bar require the application of a pressure stabilizer valve, set to 43-72 psi (3–5 bar).
Mounting 01 The mounting surface must be solid and secure. 03 Make sure the unit is level prior to securing the mounting screws. 06 07 5 04 Use mounting screws that are at least 1 inch in length. 02 The unit must be installed in an upright position with the water inlet and outlet at the bottom. 05 Do not install the unit above electrical boxes or junctions. The water heater must be installed in a manner that prevents contact with combustible materials.
Assembly Instructions 01 Connect the pressure relief device (PRD) to the unit (Figure 1) IMPORTANT – Do not omit this step. A PRD must be installed. 03 04 05 Connect the incoming water line to the heater inlet (on left side), and connect the outgoing water line to the heater outlet (on right side). Use a hose that can withstand pressure up to116 psi (8 bar) (Figure 5). Disconnect the cables from the PCB within the unit. (Figure 3) 07 02 Remove the appliance covers (Figure 2).
1 Rubber PRD Cold 2 Hot 3 4 5 Water Filter 7 6 10.
Assembly Instructions 08 Reconnect the cables to the PCB within the unit. (Figure 3) 09 Place the front cover onto the unit and reattach it with 2 screws. (Figure 2) 11 Restore power to the unit by means of the dedicated circuit breakers on the main electrical panel. 12 Do not install the heater where it may be subject to direct sunlight, and freezing temperatures.
Electrical Diagram 2 Phase, 10.
Starting the System for the First Time 01 02 Press the On/Off switch (C) to activate the heater. With water running through the unit, adjust the temperature using the Up and Down buttons. (B) The recommended temperature setting is 118°F (48°C). 03 The water heater is now ready for operation. Setting the Output Water Temperature To set the temperature, first turn on a hot water faucet and allow water to run through the heater. The digital display lights up and shows the current temperature setting.
Operation Guide Operating Instructions for the Home Owner This electric water heater is designed as a point of use product to supply hot water to types of outlets. Unlike a conventional tank storage water heater, this unit is a tankless water heater that does not store hot water. However, once you begin using the system, you will find it operates much like a conventional tank system. Tankless systems deliver hot water instantaneously on demand.
Operation Guide Freezing Temperatures If the ambient temperature falls below 32°F (0°C), protect the heater from potential damage. Shut off power to the unit by means of the dedicated circuit breaker on the main electrical panel. Open a faucet slightly to cause water to flow continuously through the device at a very low rate, without heating. Restore power to the unit when temperature conditions allow. If the water inside the heater freezes, it can cause damage that is not covered by warranty.
Care and Maintenance Stopping and restarting the system due to servicing, water stoppage, or other interruptions of operation 01 03 Press the power switch to the OFF position. Perform the maintenance or servicing tasks. 05 Reconnect power to the unit at the circuit breaker on the main electrical panel. Press the power switch to the ON position. 13 02 04 06 Shut off all power to the unit at the circuit breaker on the main electrical panel.
Troubleshooting Before calling for service, check the troubleshooting list of common issues. If you are unable to resolve a problem, contact your customer service. PROBLEM POSSIBLE CAUSE SOLUTION Water not hot enough. The water flow rate exceeds the heating capacity of the heater. Reduce the water flow rate at the faucet or slightly close the shutoff valve on the unit’s incoming water supply line to reduce the water flow rate. Increase the temperature setting on the unit.
LIMITED WARRANTY The terms of this warranty is solely subject to the original owner and is at no time transferable. A transfer of ownership will result in an immediate termination of this warranty. This warranty is valid only if product is purchased from an authorized reseller.
Agua caliente a petición Guía de instalación y manejo Thermo Boost Calentador de agua instantáneo El calentador de agua instantáneo eléctrico digital sin tanque proporciona suministro ilimitado de agua caliente al mismo tiempo que ahorra energía y agua de manera considerable www.atmorusa.com N.
Índice Página Pautas de seguridad.......................................................................................................................2 Información técnica........................................................................................................................3 Tubería de agua......................................................................................................................... 4-5 Montaje.....................................................................
Pautas de seguridad importantes 1. Pautas de seguridad Lea detalladamente este manual antes de intentar instalar el calentador de agua instantáneo. El hecho de no seguir las instrucciones de seguridad de este manual podría causar daño a la unidad, y también podría resultar daño a la propiedad, lesiones personales o pérdida de vidas. El hecho de no seguir las instrucciones de seguridad, instalación o manejo anula la garantía del producto.
Información técnica Especificaciones Eléctricas Thermo Boost 10.5 kW Elementos de calentamiento Watts Kilowatts Voltaje Amperaje del interruptor automático Interruptor automático/Relé Carga total de la conexión Tamaño de cable (mínimo) 2 10.500 W 10.5 kW 240 V 50 A Bipolar 43.7 A 6 AWG Thermo Boost 14 kW 2 14.000 W 14 kW 240 V 60 A Bipolar 58 A 4 AWG Especificaciones de la tubería de agua Flujo de agua mínimo para activar la unidad Presión de trabajo Presión probada Conexiones de agua 0.
Plomería 01 La instalación de la tubería de agua se debe realizar antes de la instalación eléctrica. 03 05 06 08 02 Antes de instalar la unidad, se debe instalar un dispositivo de alivio de presión (PRD) en la tubería de entrada del suministro de agua. La presión de operación máxima recomendada del agua es 116 psi (8 bar).
Montaje 01 La superficie de montaje debe ser sólida y firme. 03 Verifique que la unidad esté nivelada antes de asegurar los tornillos de montaje. 06 07 5 04 Utilice tornillos de montaje de 2.5 cm (1 pulg.) de longitud como mínimo. 02 La unidad se debe instalar en posición vertical con la entrada de agua y la salida de agua en la parte inferior. 05 No instale la unidad encima de cajas o conexiones eléctricas.
Instrucciones de ensamblaje 01 Conecte el dispositivo de alivio de presión (PRD) a la unidad (Figura 1) IMPORTANTE – No omita este paso. Se debe instalar un PRD. 03 04 05 Conecte el tubo de agua entrante a la entrada del calentador (en el lado izquierdo) y conecte el tubo de agua saliente a la salida del calentador (en el lado derecho). Utilice una manguera que pueda soportar una presión de hasta116 psi (8 bars) (Figura 5).
1 Hule (Caucho) PRD Fría 2 Caliente 3 4 5 Filtro de agua 7 6 10.
Instrucciones de ensamblaje 08 Reconecte los cables a la tarjeta de circuitos impresos ubicada dentro de la unidad. (Figura 3) 09 Coloque la cubierta delantera en la unidad y fíjela nuevamente con 2 tornillos. (Figura 2) 11 Restaure la energía eléctrica hacia la unidad mediante los interruptores automáticos dedicados en el panel eléctrico principal. 12 No instale el calentador donde este pudiera exponerse a la luz directa del sol y temperaturas de congelación.
Diagrama eléctrico 2 fases, 10.5 kW, 240 V TRIAC1 Elemento de calentamiento T1 L1 GND L2 Termostato TRIAC2 T2 Termostato Elemento de calentamiento S1 Interruptor de energía Sensor de temp. Tarjeta de circuitos impresos principal t Tarjeta de pantalla 21 fase, 14 kW, 240 V TRIAC1 Elemento de calentamiento TRIAC2 Elemento de calentamiento TRIAC Elemento de calentamiento T1 L1 GND L2 Termostato T2 Termostato S1 T1 Termostato Interruptor de energía Sensor de temp.
Puesta en funcionamiento del sistema por primera vez 01 02 03 Presione el interruptor de Con el agua fluyendo a El calentador de agua través de la unidad, ajuste Encendido/Apagado (C) ahora está listo para para activar el calentador. la temperatura utilizando los funcionamiento. botones Arriba y Abajo. (B) El ajuste de temperatura recomendado es 48°C (118°F).
Guía de manejo Instrucciones de uso para el propietario Este calentador de agua eléctrico está diseñado como un producto “allí donde se necesita” para suministrar agua caliente a los tipos de salidas. A diferencia de un calentador de agua convencional de almacenamiento en tanque, esta unidad es un calentador de agua sin tanque que no almacena agua caliente.
Guía de manejo Temperaturas de congelación Si la temperatura ambiente cae por debajo de 0°C (32°F), proteja el calentador contra posible daño. Apague la energía eléctrica hacia la unidad mediante el interruptor automático dedicado en el panel eléctrico principal. Abra levemente un grifo para que el agua fluya continuamente a través del dispositivo a una velocidad muy baja, sin calentamiento. Restablezca la energía eléctrica hacia la unidad cuando las condiciones de temperatura lo permitan.
Cuidado y mantenimiento Parada y reactivación del sistema después de servicio de mantenimiento, suspensión del agua, u otras interrupciones del funcionamiento 01 03 Presione el interruptor de energía a la posición “OFF” (Apagado). Realice las tareas de mantenimiento o servicio. 05 Reconecte la energía eléctrica hacia la unidad mediante el interruptor automático en el panel eléctrico principal. Presione el interruptor de energía a la posición “ON” (Encendido).
Solución de problemas Antes de llamar para solicitar servicio técnico, consulte la lista de solución de problemas comunes. Si usted no puede resolver el problema, comuníquese con su Servicio al Cliente. PROBLEMA POSIBLE CAUSA "ENCHUFAR Y LISTO" El agua no está suficientemente caliente. El caudal de agua excede la capacidad de calentamiento del calentador.
GARANTÍA LIMITADA Las condiciones de esta garantía sólo están sujetas al propietario original y no son transferibles en ningún momento. La transferencia de propiedad resultará en la terminación inmediata de esta garantía. Esta garantía es válida sólo si el producto se compra a un distribuidor autorizado.