User Manual

ManualsBrandsAtomic ManualsElectronic BasketballEscalade Double Shoot Out

For Customer Service Call 1-888-996-2729

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

When contacting Escalade Sports please provide your model number, date code (if

applicable), and part number if requestingareplacement part. These numbers are

located on the product, packaging, and in this owners manual.

Your Model Number __________________________

M01474AW

Please have your date code when inquiring about parts.

1-888-996-2729

FAX: 1-866-873-3535

gameroom@escaladesports.com

Date Code __________________________________

2 - M01474AW - - WJ

Purchase Date ______________________________

Summary of content (15 pages)

PAGE 1
We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: 1-888-996-2729 FAX: 1-866-873-3535 gameroom@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville IN 47706 Please have your date code when inquiring about parts.
PAGE 2
IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY. TWO (2) ADU LTS ARE REQUIRED TO ASSEMBLE THIS ATOMIC DOUBLE SHOOTOUT Tools Needed: Allen Wrench T1 & Wrench T2 and T3 (Included with the Hardware Kit) Phillips Screwdriver Adjustable Wrench or Socket Set is helpful but not required. A Small step ladder ! Make sure you understand the following tips before you begin to assemble your double shootout. 1.This is an electrically operated product.It is intended for INDOOR use ONLY. 2.
PAGE 3
HARDWARE IDENTIFIER (To Scale) H1 - 5/16” x 1” Allen Head Bolt (14) H5 - 1/4” x 1” Allen Head Bolt (12) H9 - 4mm x 1-3/4” Phillips Washer Round Head Screw (12) H13 - 4mm x 18mm Phillips Round Head Screw (4) H3 - 1/4” Lock Nut (12) H4 - 5/16” x 19mm Flat Washer (14) H7 - 1/4” x 15mm Flat Washer (34) H8 - 4mm x 10mm Phillips Round Head Screw (16) H11 - 1/4” x 1-1/8” Allen Head Bolt (10) H12 - 4mm x 12mm Phillips Round Head Screw (24) H2 - 1/4” x 1-3/4” Allen Head Bolt (4) H6 - 1/4” x 7/8” Allen He
PAGE 4
PARTS IDENTIFIER (Not to Scale) P1R - Right Front Leg (1) P1L - Left Front Leg (1) P3R - Right Back Bottom Leg (1) P4 - Side Back Top Leg (2) P6 - Front Leg Panel (1) P2 - Front Top Apron (1) P5L - Left Back Top Leg (1) P7 - Back Leg Panel (2) P3L - Left Back Bottom Leg (1) P5R - Right Back Top Leg (1) P8 - Leg Connecting Panel (4) P9 - Backboard (1) P13 - 45.
PAGE 5
Note: Make sure to place steel inserts this side. PARTS REQUIRED: 8 pcs - H5 Allen Head Bolt 8 pcs - H7 Flat Washer 1 pc - P3L Left Back Bottom Leg 1 pc - P3R Right Back Bottom Leg 2 pcs - P7 Back Leg Panel 1 pc - T1 Allen Wrench H5 H7 P7 H5 STEP 1: Attach two Back Leg Panels P7 between Left Back Bottom Leg P3L and Right Back Bottom Leg P3R using Allen Head Bolts H5 with Flat Washer H7 as shown in FIGURE 1. H5 P3R H7 H7 P7 Note: Make sure to place steel inserts this side.
PAGE 6
PARTS REQUIRED: 8 pcs - H7 Flat Washer 4 pcs - H9 Phillips Washer Round Head Screw 8 pcs - H11 Allen Head Bolt 24 pcs - H12 Phillips Round Head Screw 6 pcs - H14 Metal Connector 16 pcs - H15 Phillips Flat Head Screw 4 pcs - P8 Leg Connecting Panel 2 pcs - P22L Left Stiffener Board 2 pcs - P22R Right Stiffener Board 1 pc - T1 Allen Wrench STEP 3: Attach Left Stiffener Boards P22L and Right Stiffener Boards P22R to inside of Leg Connecting Panel P8 using Phillips Flat Head Screws H15.
PAGE 7
PARTS REQUIRED: 8 pcs - H3 Lock Nut 8 pcs - H6 Allen Head Bolt 8 pcs - H16 Lock Washer 1 pc - P9 Backboard 2 pcs - P17 Rim 2 pcs - P18 Rim Support Plate 2 pcs - P20 Rim Net 1 pc - T1 Allen Wrench 1 pc - T2 1/4” Wrench STEP 4: As shown in FIGURE 4, attach each Rim P17 to Backboard P9 using Allen Head Bolts H6, Rim Support Plate P18, Lock Washers H16 and Locknuts H3. Use Allen Wrench T1 and Wench T2 to tighten Nuts and Bolts. Next, attach Rim Net P20 to each Rim P17.
PAGE 8
PARTS REQUIRED: 6 pcs - H1 Allen Head Bolt 2 pcs - P4 Side Back Top Leg 6 pcs - H4 Flat Washer 1 pc - P5L Left Back Top Leg 8 pcs - H9 Phillips Round Head Screw 1 pc - P5R Right Back Top Leg 1 pc - T1 Allen Wrench STEP 6: Attach Side Back Top Leg P4 to Left Back Top Leg P5L using Phillips Round Head Screws H9, repeat this procedure with Side Back Top Leg P4 and Right Back Top Leg P5R using Phillips Round Head Screws H9.
PAGE 9
PARTS REQUIRED: 2 pcs - P15 Side Net Pole Support 1 pc - P21 Ramp Net STEP 7: Carefully slide Side Net Pole Supports P15 up through sleeve at back of Ramp Net P21 as shown in FIGURE 7. NOTE: The net ramp sleeve has a premade hole in it and the welded nut on P15 must be correctly aligned with this hole for future H6 bolt installation. P21 P15 FIGURE 7 IMPORTANT NOTE: This connecting strap is sewn closed on one side only. Install P15 into unsewn open side of this sleeve connecting strap as shown.
PAGE 10
PARTS REQUIRED: 2 pcs - H5 Allen Head Bolt 2 pcs - H6 Allen Head Bolt 6 pcs - H7 Flat Washer 2 pcs - H11 Allen Head Bolt STEP 8: 1 pc - P12 45” Front Ramp Support Round Tube 1 pc - P13 45.5” Back Ramp Support Round Tube 1 pc - P14 45.875” Back Ramp Support Round Tube 1 pc - T1 Allen Wrench DETAIL B To attach the Ramp Net P21, begin at top of board assembly and secure both sides of Ramp Net P21 using Allen Head Bolt H6 with Flat Washer H7 as shown in DETAIL B.
PAGE 11
PARTS REQUIRED: 8 pcs - H1 Allen Head Bolt 4 pcs - H2 Allen Head Bolt 4 pcs - H3 Lock Nut 8 pcs - H4 Flat Washer 8 pcs - H7 Flat Washer 8 pcs - H10 Phillips Round Head Bolt 2 pcs - P10 Back Side Ramp Support Tube P5R STEP 9: With the help of another adult, attach upper back board assembly from previous STEP 6 to lower frame assembly.
PAGE 12
PARTS REQUIRED: 2 pcs - H5 Allen Head Bolt 2 pcs - H7 Flat Washer 1 pc - T1 Allen Wrench STEP 10: Connect front of Ramp Net P21 and Steel Rod P12 using Allen Head Bolts H5 and Flat Washers H7 as shown in DETAIL D. Lastly, attach Ramp Net Straps to hook in Tube and Leg as shown in DETAIL E & F. FIGURE 10 Velcro Strap Tube DETAIL E NOTE: Hook inside the Leg. P12 H7 H5 DETAIL D NOTE: Attach Ramp Net Strap to hook in Leg.
PAGE 13
Congratulations! You have now assembled your double shootout. Please note the Care and Use Instructions below to insure many years of trouble free use of this product. ATTENTION IF THE ASSEMBLY NEEDS TO BE MOVED, PICK UP FROM FRONT AND BACK POSITION ONLY. DO NOT LIFT FROM THE SIDES. CARE AND USE OF YOUR SHOOTOUT 1. Use spray furniture polish to clean all exterior surfaces of your shootout. 2. Plug the adapter into a suitable 120v AC household outlet. 3. This product is intended for INDOOR use only. 4.
PAGE 14
PRODUCT PARTS LIST PART# 01474WJH1 01474WJH2 01474WJH3 01474WJH4 01474WJH5 01474WJH6 01474WJH7 01474WJH8 01474WJH9 01474WJH10 01474WJH11 01474WJH12 01474WJH13 01474WJH14 01474WJH15 01474WJH16 01474WJH17 01474WJH18 01474WJT1 01474WJT2 01474WJT3 01474WJA1 01474WJA2 01474WJA3 01474WJP1R 01474WJP1L 01474WJP2 01474WJP3L 01474WJP3R 01474WJP4 01474WJP5L 01474WJP5R 01474WJP6 01474WJP7 01474WJP8 01474WJP9 01474WJP10 01474WJP11 01474WJP12 01474WJP13 01474WJP14 01474WJP15 01474WJP16 01474WJP17 01474WJP18 01474WJP19 01
PAGE 15
90 DAY LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of 90 days from the original purchase.