User's Manual

ManualsBrandsAtoms Labs ManualsElectronicsControl Hub

GETTING STARTED

1. Connect the gateway box to the Internet

(1) Connect gateway box to your router via the Ethernet

cable. Then plug in the supplied power cable.

(2) The power LED indicator becomes steady RED and

you will hear the gateway box beep twice. This

means the gateway box is ready for APP setup.

(3) Launch 'OMGUARD SHC' APP. The APP will

automatically search the available gateway box and

brings up the system DID/password. If it is not

shown, Please check the system DID on the bottom

of the gateway box. Enter the system DID and default

password 123456 manually.

Note: The gateway box should be powered on and

connected to the Internet at all times.

You can continue to setup the camera and sensor(s) now.

2. Set up the IP Camera

(1) Connect the IP Camera to your router via the

Ethernet cable .

(2) Plug in the power adapter and wait until both RED

and GREED LED begin ashing.

Note: DO NOT begin the APP setup process until both

LEDs become steady on.

4. Pairing the Power Switch

Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon

and choose ‘Power Switch' and to initiate the

pairing process, following with press/hold the front

panel button until LED ashing blue.

To initiate the repeater function, press / hold the front

panel button turned orange, following with pressing the

pairing button on the device .

5. Pairing the Door / Window Sensor

Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon

and choose 'Door Sensor' and to initiate the

pairing process, following with removing and reinstalling

the battery compartment cover to complete the process.

Installing the Door/Window Sensor

Using the double-sided tape:

(1) Apply the double-sided tape to the backs of the

Door/Window sensor.

(2) Select a location on the door/window. The large

piece of the sensor should be xed on the immovable

frame of the door/window.

Align the small piece to the large one. Fix the small

piece on the movable part of the door/window

frame.

(3) When it is nished, open the door or window to test

if the sensor has been correctly installed. You'll

receive an alert from the mobile device if the APP and

sensor have been corrected installed.

FCC Compliance Statement: This device complies with Part 15 of the

FCC rules. Operation is subjected to the following two conditions:

(1)this device may not cause harmful interference, and (2) this device

must accept any interferencereceived, including interference that

may cause undesired operation.

Products with CE Marking comply with EMC Directive (2004/108/EC);

Low Voltage Directive (73/23/EEC); R&TTE (1999/5/EC); ROHS Directive

(2011/65/EU) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following

European Norms:

EMC: EN 301 489

LVD: EN 60950

Radio: EN 300 328

If the camera system no longer functions or can no longer be repaired,

it must be disposed of according to the valid statutory regulations.

Disposal of spent batteries/accumulators:

You are required by law (Battery Ordinance) to return all spent batteries and

accumulators. Disposing of spent batteries/accumulators with common household waste

is prohibited! Batteries/accumulators that contain hazardous substances are marked

with the symbols on the side. These symbols indicate that it is prohibited to dispose of

these batteries/accumulators in the household waste. The abbreviations for the respective

heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can return spent batteries

and accumulators that can no longer be charged to the designated collection points in

your community, outlets or wherever batteries or accumulators are sold. Following these

instructions will allow you to fulll the legal requirements and contribute to the protection

of our environment!

Using the mounting screws:

(1) Fix the rst mounting screw directly onto the door /

window frame (A). Place (hang) the larger piece on

to the mounted screw, remove the battery compart

ment cover to x the second mounting screw (B).

(2) Open back cover of the small piece. Use the

mounting screws to x the back cover on the

movable part of the door/window frame (C).

Mount the senor onto the back cover.

(3) When it is nished, open the door or window to test

if the sensor has been correctly installed. You'll

receive an alert from the mobile device if the APP and

sensor have been corrected installed.

6. Indoor Siren

Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon

and choose 'Siren' and to initiate the pairing

process, following with pressing the pairing button

inside the battery compartment to complete the

process.

Installing the Siren:

It is recommanded to install (wall-mount / place on at

surface) the Siren in a highly visible location with

minimum obsticles near for maximum visual and sound

alert deterrence in critical situations. A/C power option

is available, choose a suitable power outlet location for

the installation.

7. Pairing the Remote Control

Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon

and choose 'Panic Remote' and to initiate the

pairing process, following with press/hold the camera

button until the LED ashing blue.

8. APP Operation

Display device status in realtime. Tap "Status" to refresh

the status page.

Setup groups of devices for instant function activation /

deactivation.

1. Choose "+" to start a new "control".

2. Naming the control and select device(s).

3. Save.

Setup various scenarios for system to launch pre-

congured settings governing the behaviour of lights,

cameras and sirens.

1. Choose a device (initiator) from the list.

2. Choose "+" to add additional device (follower). Repeat

to add additional device(s).

3. Save.

Example: "Motion PIR" (initator) > "Power Switch"

(follower) > "Save".

3.壁貼示意: PIR、MAG

4.安裝螺絲示意: MAG

(3) Launch the 'OMGUARD SHC' APP. Click the 'ADD'

icon and choose 'Camera' to add the device to

system.

Follow the APP wizard setup process to add the

camera.

Note: The APP will search the available IP Camera in

LAN area. If the camera you're setting doesn't

appear in the searching list, please enter the

camera ID (DID) and password manually.

Installing the IP Camera:

(1) Secure the camera stand on the stable surface.

(2) Mount the camera into camera stand. Adjust the

viewing angle and x the camera tightly.

3. Pair the Motion Sensor

Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon

and choose 'Motion Sensor' and to initiate the

pairing process, following with pressing the pairing

button located inside the battery compartment to

complete the process.

Installing the Motion Sensor:

(1) Place the motion sensor upward, facing the location

to be monitored. The detection distance is up to 16

meteres.

For maximum coverage, it is recommanded to place

the motion sensor highup with its back against the

corner of walls to ensure best detection coverage.

(2) Use the double-sided tape to x the motion sensor.

OMGUARDSHC

Slot

Status

Scenario

Events

Group

List of triggered events from device(s) and playback from

camera(s).

STATUS INDICATOR

OFF

Sensor On

Sensor Triggered

Vandal Alert

Edit Mode

Sensor O

Power Low

Delete

Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off interference

and on, the user is encouraged to try to correct the by one or more

of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help