Installation Guide

Industrial Wireless Access Point
Hardware Installation Guide
Version 1.0
Updated on Feb, 2014
Technologies
Tel: [phone]
Fax: [phone]
www.atop.com.tw
P/N: 8990470G
AW5500C
Atop Technologies, Inc.
Package Check List
Inside the package you will find the following items:
■
Industrial Wireless Access Point_AW5500C x 1
■
3 / 5 dBi antenna x 1
■
3-Pin 5.08mm Lockable Terminal Block x 1
■
Din Rail Kit x 1 (Already mounted to the device)
■
Installation Guide + Warranty Card x 1
■
CD (User’s Manual / Installation Guide / Device View Utility) x 1
Installation Overview
The device’s appearance is as in the figure below.
If you have purchased the wall mount kit,
proceed to place the screws on the back of the
device as show in (Fig. 1).
Proceed then to fix the antennas to the
female RP-SMA connectors deemed to (Fig.
3). You can then choose whether to plug in
the I/O ports at this point or do it later
depending on the actual location of the
device or level of comfort for performing such
operation.
(Fig. 3)
(Fig. 2)
1.
2.
Next we can then proceed to connect the device to the LAN (switch
or PC, depending on the case), take care on using the RJ-45 connec-
tor; after this we can then proceed to the device’s settings
5.
3.
Once the plate has been firmly put in place, proceed to mount the
whole device as shown in (Fig. 4). Proceed to (Fig. 5) if you want to
remove the device from DIN-Rail.
4.
Other points to take into consideration when installing the device follow
next.
The openings to the sides are for the
device’s heat dissipation and there may
be inside hazardous voltages, please
never obstruct or cover them with any
objects or try to insert them through it.
■
AW5500C’s factory IP by default is 10.0.50.200 you can access the
device by its Web UI once it is connected to a physical network (or
using DeviceView, for more information on DeviceView, please refer
to manual, Chapter 3). Please be aware that the PC needed for this
procedure needs to be in the same subnet, or you may refer yourself
to the devices User’s Manual on Sec. 3.1.
■
Field Maintenance and Service
If the device requires servicing of any kind, you may need to disconnect
and remove it from its mounting. The initial installation should be done
in a way that makes this as convenient as possible.
Voltage/Power lines should be properly insulated as well as other
cables. Be careful when handling them so as to not trip over.
■
Do not under any circumstance insert foreign objects of any kind into
the heat dissipation holes located in the different faces of the device.
This may not only harm the internal layout but might cause harm to
you as well.
■
Do not under any circumstance open the device for any reason.
Please contact your dealer for any repair needed or follow the
instructions on section of your User’s manual.
■
(Fig. 4) (Fig. 5)
Although internal grounding has been done inside, in order to ensure
overall maximum performance and protect your device it is still
strongly advised to to ground the device properly; hazardous ESD
can come into contact with it and damage your equipment.
On the power terminal block, there is a
terminal for Frame Ground, you can
choose whether to connect it to the
grounding or you may opt to connect to
the grounding screw next to the terminal
block (the one chosen should be
connected at all times) (Fig. 2)
(Fig. 1)
F.G.
V-
V+
Optional Accessories
Item Description
AD17-24C (US-Y)
Power Adapter
Y-Type power adaptor,100-240VAC input,
0.6A @ 24VDC output, US plug
AD17-24D (EU-Y)
Power Adapter
Y-Type power adaptor,100-240VAC input,
0.6A @ 24VDC output, EU plug
WMK-454-Black Black Aluminum Wall Mount Kit
P2P Button
Pressing seconds
Working mode
1~3(s)
Restart connection
4~7(s)
AP
8~(s)
AP client
Regular AP
WDS Bridge
AP Client
P2P
ANT1
LAN
Reset
Link
WLAN RUN
COM
RUN
F.G
V-
V+
P2P
Regular AP
WDS Bridge
AP Client
P2P
ANT1
LAN
Reset
Link
WLAN RUN
COM
RUN
F.G
V-
V+
P2P