Installation Guide Owner manual
Industrial Wireless Serial Device Server
Hardware Installation Guide
Version 1.1
Updated on Feb,2014
Technologies
Tel: 886-3-5508137
Fax: 886-3-5508131
www.atop.com.tw
P/N: 89900469G
SW550xC Series
Atop Technologies, Inc.
Installation Overview
The device’s appearance is as in the figure below.
If you have purchased the wall mount kit, proceed
to place the screws on the back of the device as
shown in (Fig. 1).
Next we can then proceed to
connect the device to the LAN
(switch or PC, depending on the case), take care on using the RJ-45
connector; after this we can then proceed to the device’s settings.
Proceed then to fix the antenna to the female
RP-SMA connectors deemed to, (Fig. 3)
You can then choose whether to plug in the I/O
ports at this point or do it later depending on the
actual location of the device or level of comfort for
performing such operation.
(Fig. 3)
(Fig. 2)
1.
2.
5.
SW5501C provides one serial port with D-sub(M) or 5-pin terminal
block, please select one of them.
6.
3.
Once the plate has been firmly put in place,
proceed to mount the whole device as shown in
(Fig. 4).
Proceed to (Fig. 5) if you want to
remove the device from DIN-Rail.
4.
SW550xC’s factory IP by default is
10.0.50.100 you can access the device by
its Web UI once it is connected to a
physical network (or using Serial Manager,
for more information on Serial Manager,
please refer to its user’s manual). Please
be aware that the PC needed for this
procedure needs to be in the same
subnet, or you may refer yourself to the
User’s Manual.
■
Field Maintenance and Service
If the device requires servicing of any kind, you may need to disconnect
and remove it from its mounting. The initial installation should be done
in a way that makes this as convenient as possible.
Voltage/Power lines should be properly insulated as well as other
cables. Be careful when handling them so as to not trip over.
■
Do not under any circumstance insert foreign objects of any kind into
the heat dissipation holes located in the different faces of the device.
This may not only harm the internal layout but might cause harm to
you as well.
■
Do not under any circumstance open the device for any reason.
Please contact your dealer for any repair needed or follow the
instructions on section of your User’s manual.
■
(Fig. 4) (Fig. 5)
Although internal grounding has been done
inside, in order to ensure overall maximum
performance and protect your device it is still
strongly advised to link this point to the ground as
well; hazardous ESD can come into contact with
it and damage your equipment.
On the power terminal block, there is a terminal
for Frame Ground, you can choose whether to
connect it to the grounding or you may opt to
connect to the grounding screw next to the
terminal block (the one chosen should be
connected at all times) (Fig. 2)
(Fig. 1)
The openings to the sides are for the
device’s heat dissipation, please never
obstruct or cover them with any objects.
■
F.G.
V-
V+
F.G
V-
V+
ON
SAB
1 2 3
Good
Fair
Poor
P2P
COM
ANT1
LAN
Reset
Tx Rx
RUN
COM1
WLAN
COM
RUN
ON
1 2 3
P2P
F.G
V-
V+
ON
SAB
1 2 3
Good
Fair
Poor
P2P
COM1
COM2
ANT1
LAN
Reset
RUN
COM2
Tx Rx
COM1
WLAN
COM
RUN
ON
1 2 3 4 5 6
P2P
F.G
V-
V+
ON
SAB
1 23
Good
Fair
Poor
P2P
COM
ANT1
LAN
Reset
Tx Rx
RUN
COM1
WLAN
COM
RUN
ON
1 2 3
P2P
5-pin Terminal Block for RS-232/422/485
Pin Assignments
9-pin D-sub Connector for RS-232/422/485
1
2
3
4
5
6
7
8
9
DCD
RXD
TXD
DTR
SG
DSR
RTS
CTS
RI
RS-485 / 2-Wire RS485
(Half Duplex)
N/A
TXD+
RXD+
N/A
SG
N/A
RXD-
TXD-
N/A
1 2 3 4 5
6 7 8 9
RS-422 / 4-Wire RS485
(Full Duplex)
Pin RS-232
N/A
N/A
DATA+
N/A
SG
N/A
DATA-
N/A
N/A
1
2
3
4
5
RS-485 / 2-Wire RS485
(Half Duplex)
SG
R-
R+
T-
T+
SG
RTS
TxD
CTS
RxD
SG
DATA-
DATA+
N/A
N/A
RS-422 / 4-Wire RS485
(Full Duplex)
Pin RS-232
5 4 3 2 1
Optional Accessories
Item Description
AD17-24C (US-Y)
Power Adapter
Y-Type power adaptor,100-240VAC input,
0.6A @ 24VDC output, US plug
AD17-24D (EU-Y)
Power Adapter
Y-Type power adaptor,100-240VAC input,
0.6A @ 24VDC output, EU plug
ADP-DB9(F)-TB5
Female DB9 to Female 3.81mm TB5 Converter
WMK-454-Black Black Aluminum Wall Mount Kit
DIP Switch
COM
COM1
SW5501C
Dip Function SW Ω
3
2
1
Pull High
Pull Low
Termination
On
Off
On
Off
On
Off
1K
100K
1K
100K
120
N/A
COM
COM1
SW5502C
Dip Function SW Ω
6
5
4
Pull High
Pull Low
Termination
On
Off
On
Off
On
Off
1K
100K
1K
100K
120
N/A
COM2
3
2
1
Pull High
Pull Low
Termination
On
Off
On
Off
On
Off
1K
100K
1K
100K
120
N/A
CD (User’s Manual / Installation
Guide / Serial Manager Utility)
Package Check List
Inside the package you will find the following items:
Industrial Wireless Serial Device Server SW550xC
3dBi antenna
3-Pin 5.08mm Lockable Terminal Block
1 1
1
1
1
2
5-Pin 5.08mm Lockable Terminal Block
Descriptions DescriptionsQty
5-Pin 5.08mm Lockable Terminal Block
(for SW550C2-TB / SW550C2-Sis)
Din Rail Kit
(Already mounted to the device)
1
1
1
Qty
Installation Guide
Warranty Card
P2P Button
Pressing seconds
Working mode
1~3(s)
Restart connection
4~7(s)
AP
8~(s)
AP client