Atrie DB-120 WL User Manual Atrie DB120-WL Wireless 4-port Ethernet DSL Gateway/Router User Manual ( V 1.
Atrie DB-120 WL User Manual CONTENTS 1 OVERVIEW....................................................................................................................................................... 4 1.1 ABOUT WIRELESS ADSL ..................................................................................................................... 4 1.2 ABOUT ADSL2/2+............................................................................................................................... 4 1.3 FEATURES......
Atrie DB-120 WL User Manual 5.4 WAN LED IS ALWAYS OFF.............................................................................................................. 23 6 ROUTER TERMS ........................................................................................................................................... 24 ANNEX: SHIPPING LIST ................................................................................................................................
Atrie DB-120 WL User Manual 1 OVERVIEW 1.1 ABOUT WIRELESS ADSL An ADSL MODEM is a broadband Internet access device, which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. ADSL data transfer adapts the asymmetry model.
Atrie DB-120 WL User Manual 2 INTRODUCTION 2.1 INTERFACE INTRODUCTION 2.1.1 INDICATOR AND INTERFACE Table 2.1 Item Indicator Name Introduction POWER Red, Indicates the status of the power connection. WAN Yellow, Shows DSL line status. PPPoE Green, Indicates the status of internal PPPoE. LAN Green, Indicates the status of Ethernet interface. LINE Connected with phone line or "ADSL" port of the splitter.
Atrie DB-120 WL User Manual Introduction: 1. Use a telephone cord to connect the LINE port of the splitter with the RJ-11 port (the phone jack) on the wall. 2. Use another telephone cord to connect the ADSL port of the splitter with the LINE port of the Gateway. 3. Use another telephone cord to connect the telephone set with the PHONE port of the splitter. 4. Connect Ethernet port of the Gateway with 10/100BASE-T port of the computer using the network cable that comes with the modem. 5.
Atrie DB-120 WL User Manual 3 CONFIGURATION 3.1 DEFAULT CONFIGURATION The default configuration is 1483 bridge LLC encapsulation. If you only use this mode, there is no need to configure. The Gateway has pre-configuration the follow PVCs: Table 3.1 Name VPI VCI pvc_0_32 0 32 pvc_8_35 8 35 pvc_0_35 0 35 pvc_8_81 8 81 pvc_0_100 0 100 pvc_14_24 14 24 3.2 CONFIGURATION OF COMPUTER The default IP address for the Gateway is: 192.168.1.1 and the subnet mask is: 255.255.255.0.
Atrie DB-120 WL User Manual 3.3.2 APPLY AND SAVE ALL Press "Apply" can apply the changes you make on the page. But the apply button temporarily saves that. To make the changes permanent you need to click the "Save All" in "System Commands". Notes: The WEB-UI maybe fresh showly when you submit the configuration. So please wait a moment and don’t refresh the web page many times in secends. Press "Save All" in "System Commands" to permanently save the current configuration of the Gateway.
Atrie DB-120 WL User Manual 2. 3. 4. 5. 6. RFC 2364 PPPoA RFC 2516 PPPoE Static Bridged CLIP 3.4.1 NEW CONNECTION A new connection is basically a virtual connection. Your Gateway can support up to 8 different (unique) virtual connections. If you have multiple different virtual connections, you man need to utilize the static and dynamic routing capabilities of the modem to pass data correctly. 3.4.
Atrie DB-120 WL User Manual configuration. Give your PPPoA connection a unique name; the name must not have spaces and cannot begin with numbers. In this case the unique name is called PPPOA1. Select the encapsulation type (LLC or VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL service provider or your ISP will supply these; in this case the DSL service provider is using 0,40. Following is a description of the different options: 1.
Atrie DB-120 WL User Manual field select PPPoE and the PPPoE connection setup page is displayed; Figure 3.4 illustrates a typical PPPoE configuration. Give your PPPoE connection a unique name; the name must not have spaces and cannot begin with numbers. In this case the unique name is called PPPOE1. Select the encapsulation type (LLC or VC); if you are not sure just use the default mode.
Atrie DB-120 WL User Manual 3.4.5 DHCP CONNECTION SETUP Dynamic Host Configuration Protocol (DHCP) allows the Gateway to automatically obtain the IP address from the server. This option is commonly used in situations where IP is dynamically assigned and is not known prior to assignment. To configure the Gateway for a DHCP connection, click on Setup and then click on New Connection. At the Type field select DHCP and the DHCP connection setup page is displayed; Figure 3.
Atrie DB-120 WL User Manual Figure 3.6 (Static IP Connection Setup) 3.4.7 CLASSICAL IP OVER ATM (CLIP, DEFINED IN RFC1577) CONNECTION SETUP The Classical IP over ATM (CLIP) support provides the ability to transmit IP packets over an ATM network, The CLIP support will encapsulate IP in an AAL5 packet data unit (PDU) frame using RFC1577and it utilizes an ATM aware version of the ARP protocol (ATMARP. The CLIP support only allows for PVC support; it does not support SVC.
Atrie DB-120 WL User Manual 3.4.8 MODIFY AN EXISTING CONNECTION To modify an existing connection, from the Home screen, click setup and then click the connection you want to modify. The connections are listed as its name. As a note, if you delete the connection, to make the change permanent you need to click "Save All" in "System commands". 3.5 WIRELESS CONFIGURATION Press “WIRELESS” on the top of web pages to enter wireless section. You can select to configure wireless setup, security and management. 3.
Atrie DB-120 WL User Manual 3.5.2 WIRELESS SECURITY Press “Security” on the left menu to construct wireless security. You can select to configure WEP encryption, 802.1x and WPA authentication. z Figure 3.9 (Wireless Security) WEP Encryption Select “WEP” to enter WEP encryption page. In the page, check “Enable WEP Wireless Security” box. Authentication Type: The method of authenticating wireless station.
Atrie DB-120 WL User Manual Figure 3.10 (WEP encryption) z 802.1x Authentication Select “802.1x” to enter 802.1x authentication page. The 802.1x authentication needs a Radius server in LAN. In this page, you can input Radius server IP address, port number and secret key. z WPA authentication Select “WPA” to enter WPA authentication page. For small office and home user, there is no Radius server in LAN. So they can use WPA-PSK( Pre-Shared Key ) authentication.
Atrie DB-120 WL User Manual Figure 3.11 (802.1x authentication) Figure 3.12 (WPA authentication) 3.5.3 WIRELESS MANAGEMENT Click “Management” to enter wireless management page. You can configure Access List and Multiple SSID functions.
Atrie DB-120 WL User Manual Access List In fact, the Access List function is just like MAC address filtering and selected to permit or forbid access of wireless station with specified MAC address. Method: click “Access List” button, check “Enable Access List” box and select “Allow” or “Ban”, then input MAC address. Note: MAC address should be split by character ‘-‘ z Figure 3.13(Access List) z Associated Stations In the page, you can see information about associated wireless stations to the AP.
Atrie DB-120 WL User Manual Figure 3.14(Associated Stations) Figure 3.
Atrie DB-120 WL User Manual 4 OTHER CONFIGURATION 4.1 LAN CONFIGURATION 4.1.1 CONFIGUR GATEWAY’S IP ADDRESS As a network device, the Gateway has its own IP address. The factory sets the MODEM, at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. The user can configure they in "LAN Setup". For example, to change IP address to "10.10.10.10". Click "LAN Setup", choice "Use the following Static IP address", then input "10.10.10.10" in "IP address" and "255.0.0.0" in "subnet mask".
Atrie DB-120 WL User Manual current dynamic IP address. hours). The amount of time is in units of minutes; the default value is 3600 minutes (60 Note: If you change the start or end values, make sure the values are still within the same subnet as the Gateways IP address. In other words, if the Gateway’s IP address is 192.168.1.1 (default) and you change the DHCP start/end IP addresses to be 192.128.1.2/192.128.1.100, you will not be able to communicate to the Gateway if your PC has DHCP enabled. 2.
Atrie DB-120 WL User Manual 5 TROUBLESHOOTING Below is a list of commonly asked questions. issues to see if they help solve your problem. Before calling technical support, please look through these 5.1 THE GATEWAY IS NOT FUNCTIONAL 1. 2. 3. 4. 5. 6. Check that the POWER LED is ON. Check that the network cables are installed correctly and the LAN LED is ON. Check that the WAN LED is ON. Check the settings on your PC. Check the Gateway’s settings.
Atrie DB-120 WL User Manual 5.4 WAN LED IS ALWAYS OFF 1. Make sure you have DSL service. You should get some kind of information from your ISP, which states that DSL service is installed. You can usually tell if the service is installed by listening to the phone line; you will hear some high-pitched noise. If you do not hear high-pitched noise, contact your ISP. 2. Verify that the phone line is connected directly to the wall and to the line input on the Gateway.
Atrie DB-120 WL User Manual 6 ROUTER TERMS What is a firewall? A firewall is protection between the Internet and your local network. It acts similarly to the firewall in your car, protecting the interior of the car from the engine. Your car's firewall has very small opening that allow desired connections from the engine into the cabin (gas pedal connection, etc), but if something happens to your engine, you are protected. The firewall in the router is very similar.
Atrie DB-120 WL User Manual ANNEX: SHIPPING LIST Item Quantity ADSL MODEM 1 Splitter 1 User Manual 1 Power Supply 1 Cable Cat5 RJ45 1 Telephone Line 2 Warranty Certificate 1 Atrie Technology Pvt. Ltd. Corporate office: Atrie House, # 591,3rd Block, Koramangala, Bangalore -560 034 India Registered office: #B-121,Ground Floor ,Kalkaji, New Delhi – 110019 Regional office (West): #C/312,3rd Floor, Gokul Arcade, Vile Parle(E) Subhash Road,Mumbai - 400057 Web: http://www.atrieindia.
