ERGO PRO CORDLESS BACKPACK VACUUM OWNER’S MANUAL Model: VACBPAIC 26V, 300W Atrix 1350 Larc Industrial Blvd. Burnsville, MN 55337 www.atrix.com sales@atrix.com Telephone: 952.894.6154 Toll Free Telephone: 800.222.6154 Fax: 952.894.
Battery MUST be REMOVED from the Vacuum prior to charging. Failure to follow the warnings and instructions may result in shock, fire, property damage and or serious injury or death. IMPORTANT SAFETY INSTRUCTIONS Per CFR 49, Lithium Ion batteries are considered “hazardous goods.” As such, they are subject to SPECIAL handling and packaging regulations for ground and air shipping. Proper shipping procedures compliant with CFR 49 MUST BE FOLLOWED.
7. DO NOT put any objects into openings. Do not use with any opening blocked, keep free of dust, lint, hair, and anything that may reduce air flow. 8. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. 9. Use with extra care when cleaning on stairs. 10. DO NOT vacuum flammable or combustible materials or anything that is burning or smoking, such as cigarettes, matches, or hot ashes. 11.
GETTING TO KNOW YOUR ERGO PRO CORDLESS VACUUM 5 6a 12 6b 13 15 14 4 16 7 8 9 10 11 1. Replacement 1.5” Lid Grey (VACBPAILIDG) 2. Replacement Latch (BP34-38) 3. 3a & 3b Assembly - Replacement Handle, Webbing and Harness (BPAIHARN) 4. On/Off Power Switch 5. Replacement Hose 1.5” (VACBPAI39) 6. 7a - 1.5” Aluminum Wand Hose End (VACBPAI37) 7b - 1.5” Aluminum Wand Utensil End (VACBPAI38) 7. HEPA Bag (VACBP6- 10P) 8. Reusable Cloth Shake-Out Bag (VACBP8) 9. and 10.
OPERATING INSTRUCTIONS Assembling Your Vacuum 1. Push/press fit the hose into the lid opening. (Fig 1) (Fig. 1) 2. To connect the hose and attachment wand, slide the hose over the hose end wand attachment and over the bump by approx. ½”. (Fig. 2) (Fig. 2) 3. Take the hose end attachment wand and insert it into the lower attachment wand (utensil end). (Fig. 3) (Fig.
4. Secure the utensil to the end of wand. Align the copper ring with the groove on the tool to ensure a secure fit (Fig. 4) (Fig. 4) Using Your Vacuum 1. Ensure the battery pack is assembled and locked in the vacuum. 2. Connect hose to the lid of the vacuum. 3. Connect the Aluminum Wands together, then connect the hose to the assembled wand, and secure utensil for use. 4. Correctly place shoulder straps on each shoulder and secure the waist band (Fig.
Replacing the HEPA Bag 1. To open the canister lid, pull up the canister lid tabs on each side of the unit and remove canister lid. (Fig.1) Fig. 1 Fig. 2 2. Pull the tab on the HEPA bag holder out slightly and flip upwards. (Fig. 2) 3. Holding the HEPA bag in your hand, slide/pull it out of the bag holder and dispose. 4. Insert/slide new bag. Cardboard face should rest securely in the bag cover guides. (Fig. 3) Fig. 3 Fig. 4 Cleaning the Cloth Shake-Out Bag 1.
Cleaning or Replacing the HEPA Pre-Motor Filter Important Please Note: The HEPA pre-motor filter will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. Because of this incredible filtration performance, the HEPA premotor filter will accumulate many fine dust particles that are difficult to see. Be assured that the HEPA pre-motor filter is doing the job. Clean the HEPA pre-motor filter when dirty as described in this section. 1.
Cleaning the Exhaust Filter 1. Pull up and hold the exhaust tab and pull out the exhaust cover. (Fig. 7) 2. Remove the exhaust filter. 3. As necessary, hand wash or replace the cloth filter with tap water and let dry before reinserting it. (Fig.
HOW TO CHARGE THE BATTERY PACK When using the charger, basic precautions should always be followed, including the following: Battery and Charging Safety To reduce the risk of electric shock, fire, battery explosion, or injury: 1. Basic information and warning for ATRIX Battery and Charger are contained below. For detailed usage and warning information, read the HOW TO CHARGE THE BATTERY PACK carefully before using this unit. 2. Use only the ATRIX Charger and ATRIX Battery Pack. 3.
SPECIFICATIONS AND PARTS Charger Specification: Charger input: 100-240V 50/60Hz AC Charger output: 30V 4A Battery Specification: Lithium Polymer chemistry 26V Approximate charge time: 4 Hours Approximate run time: 60 Minutes 1. 26V Battery Pack (BPAIBAT) 2. Battery Charger (BPAICHG) 3.
OPERATION When using the charger, basic precautions should always be followed, including the following: Battery MUST be REMOVED from the Vacuum prior to charging. Failure to follow the warnings and instructions may result in shock, fire, property damage and or serious injury or death. CHARGING LITHIUM POLYMER BATTERY PACKS It is not necessary to drain the battery pack completely before recharging.
6. Plug the charger’s power cord into the charger. 7. Plug the round connector on the charger’s cord into the battery pack. 8. Plug the charger’s power cord into wall outlet. 9. The indicator light will turn red when charging and turn green when fully charged. The battery pack may require approximately 3.5 to 4 hours to fully charge. 10.
Atrix ERGO PRO Cordless Backpack Vacuum WARRANTY INFORMATION Warranty/Service Information, please contact Atrix. Atrix Ergo Pro Cordless Backpack Vacuum, Part no. VACBPAIC, Limited Warranty: To the original user purchasing the Atrix Ergo Pro Cordless Backpack Vacuum, Atrix warrants that the vacuum will be free of defects in material and manufacture for a period of one (1) year from the date of purchase. Should any failure to conform to this warranty appear within this period, contact Atrix.
