SBU2000 / 2Track base unit Installation and Operation Guide
Information in this documentation is subject to change without notice and does not represent a commitment on part of Elmo-Tech Ltd. The software described in this document is subject to the license agreement that is included with the product, which specifies the permitted and prohibited uses of the product. Any unauthorized duplication or use of this documentation, in whole or in part, in print, or in any other storage or retrieval system is prohibited.
Table of Contents 3
Installation Instructions for the Electronic Monitoring System 1. SBU2000 Monitoring Unit Placement In order to install the Electronic Monitoring System, you will need to find the best location for the SBU2000 Monitoring Unit. The ideal location for the SBU2000 Monitoring Unit is as close as possible to the center of the house.
The SBU2000 Monitoring Unit should be placed on a flat horizontal surface, at least 3 feet off the ground and at least 1 foot away from the wall. The SBU2000 Monitoring Unit should be in an open area away from other electrical appliances, personal computers, laptops or metal objects. 2. Installing the SBU2000 Monitoring Unit In order to install the SBU2000 Monitoring Unit, perform the following steps: 1.
5. After completing the initialisation tests successfully the SBU2000 Monitoring Unit beeps again and the left and right external LED indicators, located on the rear panel of the SBU2000 Monitoring Unit are turned on. This indicates that the SBU2000 Monitoring Unit is in a working state and has automatically switched to standby mode. 3. Installing the 2TRACK Installing the 2TRACK system involves: 1. Collecting the appropriate installation equipment and tools 2.
Warning: The Tracker unit’s battery must be fully charged. Verify the battery’s status by plugging the charger into the Tracker unit and removing it. The Tracker unit’s screen displays a power bar to indicate the charge level of the battery. b. Installation Tools You will also need the following installation tools: 1. Manual Reset Device (MRD) – for activating the Transmitter 2. Strap locking tool – for locking the Transmitter 3. 0.2” (5mm) flat head screwdriver – for opening the locking clip 4.
4. Place 2TRACK in SBU2000 Unit The SBU2000 unit device used to recharge the 2TRACK and transmit all GPS location information, violation information, and house arrest status. It also monitors the Ankle Bracelet when the 2TRACK is placed in the base unit (docked). 5. Installation Manual for bracelet unit Bracelet To Attach the Bracelet 1. Match the Bracelet serial number on the Bracelet case to the number on the Bracelet serial number in the hardware list in PCE.
2. Once you have the strap attached, push the locking pin through the holes on the bracelet and into the strap until it locks into place 3.
To Remove the Bracelet 1. Cut the strap 2. Using the screwdriver provided, turn the right locking pin counter clockwise and the left locking pin clockwise to remove 3. Lift each side of the pin up from the strap and remove. Slide both ends of the strap out of its channel. Dispose of the strap 4. Clean the bracelet with mild detergent. Rinse, dry, and return to your inventory. Downloading the Curfew Schedule Once the monitoring system has been installed, perform the following: 1.
6. FCC Notices The SBU2000 complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation. 3) Changes or modifications not expressly approved by Elmo Tech Ltd could void the user’s authority to operate the equipment.
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with the Smart Base Unit, model: SBU x000yyy, for repair or warranty information please contact: Pro Tech Monitoring, lnc., 1838 Gunn Highway, Odessa, FL 33556, Phone 888.67.SMART, FAX 813.