ElmoTech Ltd. Version 1.0 STAR UNIT User MANUAL Version 1.
Version 1.0 ElmoTech Ltd. Prepared by: Elmo-Tech Ltd. Corporate Headquarters 2 Rehov HaBarzel P.O. Box 13236 Ramat HaChayal 61132 Tel Aviv Israel Tel: +972-3 – 6478871 Fax: +972-3 – 6478872 Visit us at: www.elmotech.com © 2001, Elmo Tech Ltd. All rights reserved.
ElmoTech Ltd. Version 1.
Version 1.0 ElmoTech Ltd.
ElmoTech Ltd. Version 1.0 Table of Figures Figure Page FIGURE 1 IDEAL HOME UNIT LOCATION ........................................................8 FIGURE 2 THE STAR UNIT ...........................................................................10 FIGURE 3 PROTRUDING SIDE OF TRANSMITTER DIRECTED UPWARDS ..........
Version 1.0 ElmoTech Ltd. THE MONITOR CENTER/ PROBATION AGENCY At the Monitor Center/Probation Agency: 1. Enter the Offender’s data in the monitoring application. This can be done well in advance, even before the actual equipment is allocated and installed. 2. Enter the following equipment data in the monitoring application. • STaR unit Serial No. - Check that the number entered matches the number on the STaR unit. • Transmitter Serial No.
ElmoTech Ltd. • Version 1.0 Screwdriver (to open a clip if necessary). It is recommended to use a 5 mm flat head screwdriver. It is always advisable to bring an extra set of strap clips to cater for the event in which the first set may be accidentally damaged during the installation.
Version 1.0 ElmoTech Ltd. THE OFFENDER’S PREMISES Monitoring System Location In order to install the Monitoring System, you will need to find the best location for the Home Unit. The ideal place for the Home Unit is in the center of the house, 3 feet off the ground and at least 1 foot away from the wall. Figure 1 Ideal Home Unit Location The Home Unit should be placed in an open area away from other electrical appliances, personal computers, laptops or metal objects.
ElmoTech Ltd. Version 1.0 The STaR unit should be placed in the proximity of not more than 15 feet from the Home Unit, and should be connected to the charger when at home. Activating the STaR Unit In order to activate the STaR unit: 1. Connect the charger (power adapter) to the wall socket. 2. Plug the appropriate end of the charger cord into the charger socket on right side of the STaR unit. 3.
Version 1.0 ElmoTech Ltd. Antenna LED Indicators LCD Panel Acknowledge and LCD Backlight Buttons Charger Socket Figure 2 The STaR Unit If, at the end of the start-up self test, audible beeping sounds are heard and both the LED’s flash for 10 seconds, it could indicate one of the following possible failures: ● Case open micro-switch malfunction ● Range threshold values lost (maximum reception range is used in this case).
ElmoTech Ltd. Version 1.0 Downloading the Curfew Schedule and Default Offender Parameters Downloading the curfew schedule and default offender parameters requires that the CMS (Central Monitoring System) telephones the STaR unit and transmits a series of signals to the STaR unit in order to allow it to monitor the Offender. After the STaR unit has been activated, perform the following: 1. Verify that the default message is displayed in the LCD panel, i.e. ‘STaR system is waiting for download’. 2.
Version 1.0 ElmoTech Ltd. • Sanity calls intervals • Events response configuration • GPS operational parameters (if different than default) Installing the Transmitter The officer should bring the following equipment for a Transmitter installation: • Transmitter • Male and female strap Clips • Electronic key • Strap holder • Locking tool • Flat-head screwdriver Calibrating the Transmitter Before any installation, the Transmitter has to be turned-on and calibrated.
ElmoTech Ltd. Version 1.0 matching the pair of metal pins on the Transmitter strap. Hold the Electronic key in this position while you do the next step. 5. Press the red button on the Electronic Key down for one second; the red light turns steadily on for two (2) seconds. 6. If the transmitter successfully receives the reset command, the red light, on the Electronic Key, will flash for two (2) seconds.
Version 1.0 ElmoTech Ltd. of the clip fits with the edge of the strap. Make sure the silver line is visible. 3. Wrap the Transmitter around the offender’s ankle at its narrowest point. Ensure that the protruding side of the Transmitter is directed upwards. Figure 3 Protruding side of Transmitter directed upwards It is important that the Transmitter fits tight around the offender’s ankle, but isn’t squeezing.
ElmoTech Ltd. Version 1.0 5. Ask the Offender to stand up and move around to insure that the Transmitter is comfortable. 6. Fasten the two Clips with the locking tool. Be sure to fasten all the four pins well. An audible clicking sound should be heard, indicating that the Clips are closed properly. Don’t install the Transmitter over a thick sock, since the transmitter will get too loose once the sock is removed.
Version 1.0 ElmoTech Ltd. • The LED indicator (right) on the STaR unit flashes for a while and then returns to its steady state. • After the LED indicator (right) on the STaR stops flashing, the left LED blinks 3 times in quick sequence accompanied by 3 audible beeping sounds. This means that range test has started. The STaR unit will be in the range test mode for approximately 15 minutes, unless the Monitor Center/Agency terminates it manually.
ElmoTech Ltd. 5. Version 1.0 Wait for up to two minutes in each checked location. During these two minutes four transmissions should be received from the PID. If four transmissions are received before two minutes have elapsed, you can move with the Offender to the next location to be checked. If less than four transmissions are received, phone the Monitor Center/ Agency and ask to change the range setting to a longer range.
Version 1.0 ElmoTech Ltd. General Rules for the Offender The following points describe the general rules for the Offender and also which appliances are prohibited in his\her premises.
ElmoTech Ltd. Version 1.0 REMOVING THE MONITORING SYSTEM Sometimes it is required to remove the Monitoring System before the defined confinement period is completed. Before deactivating the STaR unit, the End of Service procedure should be performed. Initiating an End of Service Phone the Monitor Center/Agency personnel and ask them initiate a STaR unit End of Service. Initiating an End of Service before deactivating the STaR unit is essential in order to preserve the STaR unit’s internal backup battery.
Version 1.0 ElmoTech Ltd. Removing the Transmitter It is recommended that only an Officer remove the Transmitter. To remove the Transmitter perform the following steps: 1. Check to see if the Clip has been tampered with. Be aware of the following signs: iCracks on the clips iBroken pins. iSign of adhesive or glue. 2. Use a screwdriver to break the disposable Clips. Be careful not to damage or cut the strap. 3. Collect all the fragments of the Clip. Do not leave any disposable items.
ElmoTech Ltd. Version 1.0 matching the pair of metal pins on the Transmitter strap. Hold the Electronic key in this position while you do the next step. 4. Press the Black button on the Electronic Key down for one second; the red light turns steadily on for two (2) seconds. 5. If the transmitter successfully receives the shut down command, the red light, on the Electronic Key, will flash for two (2) seconds.
Version 1.0 ElmoTech Ltd. TRANSMITTER CLEANING INSTRUCTIONS The Transmitter is made of a single mold, especially designed to protect the integrity of the electronic circuits during daily use and while it is being cleaned. A soft brush and an Alcohol based solution; soapy water or Lysol can be used to clean the Transmitter. For additional safety and user comfort it is recommended that after cleaning with any of the above, you wash and wipe the Transmitter with clear water before it is re-used.
ElmoTech Ltd. Version 1.0 TRANSMITTER STRAP REPLACEMENT After some time and depending on the wear and tear of the Transmitter, the Transmitter straps need to be replaced. Reasons for Strap Replacement The following points indicate possible reasons for replacing a Transmitter strap: • Visible damage to one or both straps • Unexplainable strap tamper alarms • Transmitter will not calibrate When testing the straps before changing them, make sure the clip is properly locked.
Version 1.0 ElmoTech Ltd. Equipment Needed for Strap Replacement The following list indicates equipment the Officer will need to complete a strap replacement: • 1 Transmitter “body” • 1 pair of replacement straps (long/medium non-pins side and long/medium pins side) • Screw driver • Extra screws • Extra strap clasps (male and • Electronic Key Replacing the Transmitter Straps Following are detailed instructions for replacing the Transmitter straps: 24 1.
ElmoTech Ltd. Version 1.0 6. Close the screw with the Phillips screwdriver. It has to be closed firmly, but not too tight since this can damage the strap (maximum allowed torque is 1 Newton x Meter). 7. Test the new strap by performing a calibration (see the section, Calibrating the Transmitter). If, after the calibration, the Transmitter does not reset, repeat steps 1-3 and make sure that the strap is positioned correctly over the pins. Then repeat steps 5-6 and perform another reset.
Version 1.0 ElmoTech Ltd. FCC NOTICES STaR Unit FCC Notices The STaR Unit Model 800 has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if installed and used in accordance with the instruction, may cause harmful interference to radio communications.
ElmoTech Ltd. Version 1.0 STaR Unit Customer Information The STaR Unit complies with FCC part 68 Rules. On the bottom panel of this equipment is a label that contains, among other information, the FCC Number and Ringer Equivalence Number (REN is 1.0 B). If the STaR Unit is not operating properly it may cause harm to the telephone network and the telephone company will notify you in advance that temporary discontinuance of service may be required.
Version 1.0 ElmoTech Ltd. This device has been tested and found to comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if installed and used in accordance with the instruction, may cause harmful interference to radio communications.
