TRXS-830 Ankle Transmitter User Guide
Information in this documentation is subject to change without notice and does not represent a commitment on part of Elmo-Tech Ltd. The software described in this document is subject to the license agreement that is included with the product, which specifies the permitted and prohibited uses of the product. Any unauthorized duplication or use of this documentation, in whole or in part, in print, or in any other storage or retrieval system is prohibited.
Table of Contents 1 Introduction.................................................................... 2 2 Installing the Transmitter ............................................... 3 Activating the Transmitter .................................................. 3 Attaching the Transmitter .................................................. 5 3 Removing the Transmitter .............................................. 7 Deactivating the Transmitter ..............................................
E3 Receiver Unit and Transmitter Installation Guide 1 Introduction The TRXS-830 is an inconspicuous transmitter used in house arrest applications and is attached to the client's ankle or wrist by means of a tamper-detecting strap. The client's presence (or absence) is tracked constantly by radio transmissions between the Transmitter and the E3 Receiver Unit. When the client enters or leaves the defined home environment, the E3 Receiver Unit records the event.
2 Installing the Transmitter Once the E3 Receiver Unit has been connected and is working correctly, you can calibrate and install the Transmitter (Tx). Check that you have the following equipment items before you install the Transmitter: f Transmitter (Tx) and Strap holder f Locking clips (male and female) f Strap holder f Electronic key f Locking tool f Screwdriver (to open the clips if necessary).
E3 Receiver Unit and Transmitter Installation Guide 4. Hold the electronic key and the Transmitter strap in this position while you perform the next step. 5. Press the ‘ON’ on the electronic key for one second; the red LED light on the electronic key turns steadily on for two seconds. If the Transmitter successfully received the activate/calibrate commands the red light on the electronic key will flash for two seconds.
2 Installing the Transmitter Attaching the Transmitter To attach the Transmitter to the offender: 1. Place a strap holder over the short strap (strap with pin side) of the Transmitter. 2. Attach the female Clip to the underside of the Transmitter’s short strap (to lie against the Offenders skin). Check that the closed end of the clip fits with the edge of the strap. 3. Wrap the Transmitter around the Offender’s wrist/ankle at its narrowest point. 4.
E3 Receiver Unit and Transmitter Installation Guide 6. Cover the female clip with the male clip ensuring that the pins on the male clip fit correctly into the female clip (the grooves on the side of each clip must match). 7. Ask the Offender to stand up and move around to ensure that the Transmitter is comfortable. 8. Fasten the two clips using the specially designed locking tool. An audible clicking sound should be heard, indicating that the clips are closed properly.
3 Removing the Transmitter 3 Removing the Transmitter To remove the Transmitter: 1. Check the following signs to see if the clips have been tampered with: f Cracks on the clips f Broken pins f Sign of adhesive or glue 2. Being careful not to damage or cut the strap, use a screwdriver to break the disposable clips. Screwdriver Grooves 3. Collect all the fragments of the broken clip. Do not leave any disposable items.
E3 Receiver Unit and Transmitter Installation Guide Deactivating the Transmitter Deactivating the Transmitter is essential to preserving the unit’s internal battery. To deactivate (turn off) the Transmitter: 1. Hold the Transmitter in your hand with the metal pins (along the strap) pointing towards you. You will need to support the underside of the strap. 2. Hold the electronic key in your other hand, with the ‘OFF’ button pointing towards the open or free end of the strap.
4 Maintenance Cleaning the Transmitter The Transmitter is made of a single mold, especially designed to protect the integrity of the electronic circuits during daily use and while it is being cleaned. The following cleaning methods are approved by Elmo-Tech: f Manual Cleaning – using a soft brush and approved cleaning product. f Using a Dishwasher – together with an approved cleaning product. To clean the Transmitter manually: 1. Remove the Transmitter from its carrying case. 2.
E3 Receiver Unit and Transmitter Installation Guide 5. Using a dry cloth or towel, dry the outside of the Transmitter and place it on a towel with its inner side facing up. 6. Using a soft brush, gently brush the inner side of the Transmitter along the tracks. 7. After cleaning, wash the Transmitter in clean water. 8. Using a dry cloth or towel, dry the Transmitter thoroughly. 9. Place the strap holder back onto the short strap of the Transmitter. 10. Place the Transmitter back into its carrying case.
4 Maintenance Replacing the Transmitter Straps After some time and depending on the wear and tear of the Transmitter, the straps on the Transmitter will need to be replaced.
E3 Receiver Unit and Transmitter Installation Guide To replace the Transmitter straps: 1. Using the screwdriver, open the screw(s) that holds the strap clasp to the Transmitter and remove the strap clasp. 2. Gently shake the strap loose from the Transmitter body, being extra careful not to damage the metal pins on the Transmitter body. 3. Position the new strap over the Transmitter body. Notice that the two small holes on the strap have to lie exactly over the two metal pins. 4.
5 Specifications Transmitter Specifications f Transmitter size: f Transmitter weight: f Fully adjustable / reusable f Disposable locking clip f Shock resistant f Multi tamper protection f Battery operational life: f Battery shelf life: 2-3 years f Waterproof to 4.5 m (15 ft) f Frequency: 318MHz 5.5 x 4.2 x 1.5 cm (2.2 x 1.65 x 0.67 in) straps 18 / 36 months 50 g (1.
E3 Receiver Unit and Transmitter Installation Guide 6 FCC Information TRXS-830 FCC ID: LSQ-TRXS-830 FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
