User's Manual

ManualsBrandsAttenti ManualsElectronicsANKLE WORN GPS TRACKING DEVICE

SMART

ACTIVE TRACKING

System Overview

Pro Tech’s Wearable Miniature Tracking Device (WMTD) utilizes GPS satellites to establish an

offender’s location by utilizing the cellular network to transmit the data.

Alert Button

Bracket

Serial Number

Charging Port

WMTD Communication and GPS Point Storage

• The standard WMTD call-in interval is once every hour while in compliance

• The WMTD will call Pro Tech as soon as a violation occurs, if a Contact is selected

• If the WMTD is not able to make a call because of poor cellular coverage, it will

continue trying to call in until it is successful

• The WMTD collects a GPS point every minute. If a Geographic Rule is in violation,

the WMTD will collect a GPS point every 15 seconds.

Summary of content (11 pages)

PAGE 1
SMART® ACTIVE TRACKING System Overview Pro Tech’s Wearable Miniature Tracking Device (WMTD) utilizes GPS satellites to establish an offender’s location by utilizing the cellular network to transmit the data.
PAGE 2
WMTD Indicator LEDs There are three LEDs on the top of the WMTD, identified as Power, GPS, and Zone. The three LEDs work separately and provide the offender with information. It is possible for any LED to be flashing Green or Red and it is acceptable for the LEDs to be off. The WMTD will vibrate to provide an indication that the offender must look at the LEDs. The LEDs function as follows: PWR Zone GPS PWR LED • This LED indicates the condition of the WMTD battery.
PAGE 3
Rule Definitions Hardware Rules WMTD Battery • The battery is getting low and the device needs to be charged. The device must be charged for a minimum of two hours daily (the hours do not have to be consecutive). When the battery needs to be charged, the device will vibrate three times consecutively and then once every ten minutes until connected to the charger. During this time, the Power LED will blink Red.
PAGE 4
Rule Definitions Cont. Geographic Rules Zone Rules- The offender has violated a Zone set up by the user. The device will vibrate three times consecutively and once every ten minutes while still in violation, if the Notify With Vibrate feature is checked. The Zone LED will blink in Red.
PAGE 5
Activating the WMTD Equipment 1. Press and hold the Alert Button on the front of the WMTD for 3 seconds. If the “PWR” LED is Green then proceed with activation. If the “PWR” LED is Red or does not light up at all, then the WMTD will need to be charged prior to activating. 2. Push tamper plugs into the back of the brackets of the WMTD. Be sure to insert the left side first. 3.
PAGE 6
Activating the WMTD Equipment Cont. 7. Using the strap cutters, cut the strap according to the measurement taken in step six. Wipe off any fiber optic cable residue left on the strap after cutting has been completed. 8. Place remaining pin tray on a flat surface and insert measured end of the underneath side (the bottom) of the strap into the pin tray. 9. Place the WMTD on the offender’s leg just below the ankle bone and insert the strap with attached pin tray into the bracket until it snaps in place.
PAGE 7
DEACTIVATING SYSTEM HARDWARE • In PCE, go to the Hardware Tab and click the Deactivate Hardware button. The following screen will appear. Check the items that you wish to deactivate and the reason for the deactivation. Click the Commit button at the bottom of the screen.
PAGE 8
Removing the WMTD Equipment 1. Cut the strap by using the strap cutters and remove the WMTD from the offender’s leg. 2. Using a Pro Tech flathead screwdriver, push on the tamper plugs to break them. 3. Use the screwdriver to remove the tamper plugs from the brackets. 4. Using the screwdriver, press down the latch attached to the pin tray. 5. While keeping the latch depressed, pull the strap with the attached pin trays out of each bracket . 6. Discard tamper plugs, pin trays and the straps.
PAGE 9
Enrolling an Offender Quick Reference Open PCE.
PAGE 10
Enrolling an Offender Quick Reference Cont.
PAGE 11
FCC Certification The Wearable Miniature Tracking Device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference and 2.) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: NC3WMTD3418, NC3WMTD3318, NC3WMTD3433, PRO TECH MONITORING IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.