Installation and Operation Manual ATTO ExpressPCI UL4S Single Channel Ultra320 SCSI, PCI-X Host Adapter ATTO ExpressPCI UL4D Dual Channel Ultra320 SCSI, PCI-X Host Adapter ATTO ExpressPCI UL5D Dual Channel Ultra320 SCSI, PCI Express Host Adapter ATTO ExpressPCI UL5D LP Dual Channel Ultra320 SCSI, Low-Profile PCIe Host Adapter © 2007 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks of their respective holders.
Contents 1 SCSI is a key technology for storage 1 SCSI advantages Glossary 2 ATTO ExpressPCI Ultra320 SCSI solutions 3 Ultra 320 SCSI features Common features UL4D, UL4S specific features UL4D specific features UL4S specific features UL5D, UL5D LP specific features UL5D specific features UL5D LP specific features SCSI host adapter selection guide 3 Hardware installation 5 System requirements Installation 3.1 Cabling and termination ......................................................
1 SCSI is a key technology for storage Ultra320 SCSI represents the seventh generation of SCSI technology, an I/O interface that increases performance while maintaining backward compatibility and legacy support. From its roots in 5 MB/sec. transfer rates, SCSI driving the unprecedented growth in storage that has evolved as the leading interface for disk drive pushes the I/O bandwidth, requiring more connections in high performance servers. It advanced interfaces to handle data transfer.
Term Definition double transition clocking Increases the data line frequency to equal that of the request signal, allowing sampling on both the leading and trailing edges of the request signal. Clocking can be set to ensure compatibility with legacy devices. flow control The target indicates to the initiator when the last packet of a data stream will be transferred so that the initiator can flush FIFOs and terminate pre-fetch sooner than previously possible.
2 ATTO ExpressPCI Ultra320 SCSI solutions The Ultra320 SCSI host adapter represents the seventh generation of SCSI technology, an I/O interface that is committed to increased performance while maintaining backward compatibility and legacy support. The ATTO ExpressPCI UL4S is a single channel Ultra320 SCSI, PCI-X host adapter, the ATTO ExpressPCI UL4D is a dual channel Ultra320 SCSI, PCI-X host adapter, and the ATTO ExpressPCI UL5D and UL5D LP are dual channel Ultra 320 SCSI PCI Express (PCIe) host adapters.
• UL5D, UL5D LP specific features Power • 0.75 typical/2.0 max. Amps @ + 5.0 /VDC • 0.05 Amps @ + 12.0 VDC • • UL4D specific features • • • Two external VHDCI and two internal highdensity 68-pin connectors Supports up to 30 SCSI bus IDs (15 per channel) Dimensions • Length: 6.521” • Height: 4.450” UL5D specific features • • UL4S specific features • • Supports up to 30 SCSI bus IDs (15 per channel) PCI Express (PCIe) bus management • PCI Bus master rate 2-GB/sec. • PCI Express 1.
3 Hardware installation Install the ATTO ExpressPCI Ultra320 host adapter and attach your SCSI devices to it using the instructions below. To get the best performance from your ATTO Express Ultra320 host adapters, use Ultra 320 SCSI devices. Devices in the middle of the bus, including the ATTO ExpressPCI adapter, must have termination removed or disabled. ATTO ExpressPCI SCSI adapters select the proper termination if left in auto termination mode.
6 Hardware installation
3.1 Cabling and termination Cables and devices must be chosen to maximize performance and minimize the electrical noise from the high-speed data transfers available with the SCSI protocol. Cabling and termination methods become important considerations. Exhibit 3.1-1 The following table lists the maximum number of devices you may connect at specific cable distances using differential and single-ended SCSI in various SCSI environments. Max. bus lengths, meters Bus speed Bus width MB/sec. max.
• A narrow terminator should be used on the last narrow device to terminate the rest of the SCSI bus. Use an LVD terminator if you are only using LVD devices. Although you can use a Single-Ended terminator, all devices will be limited to Ultra SCSI speeds. Single-Ended devices require a Single-Ended terminator. If you use an LVD terminator with SingleEnded devices, the system may hang or devices may not be seen on the SCSI bus.
4 Installing drivers After installing the ATTO ExpressPCI host adapter, you must configure your system to recognize and use it by installing drivers for your operating system. Note If you already have one or more ExpressPCI adapters installed and you are installing additional adapter(s), you do not need to perform any of these procedures unless you are updating a previously installed driver.
5 Updating hardware flash ATTO ExpressPCI adapters ship with the latest firmware installed. If you are performing a new adapter installation, you do not need to update the firmware. If you are upgrading a previously installed driver, update the adapter firmware to ensure proper operation. Visit the ATTO Technology website, Use the ExpressPCI BIOS Setup Utility www.attotech.com, for the latest drivers and Note firmware. BIOS utilities are not available on Itanium systems.
Appendix A Standards and compliances The equipment described in this manual generates and uses radio frequency energy. The Technical Specification sheet for a particular ATTO ExpressPCI host bus adapter list certifications for that model. FCC standards: radio and television interference This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Appendix B ATTO product guide Contact an ATTO Technology authorized sales representative to order. SCSI adapter selection guide Ultra 320 SCSI Product Features UL5D UL5D LP UL4D UL4S 640 640 640 320 • • • • • • • • Number of SCSI Channels 2/2 0/2 2/2 1/1 Number of SCSI IDs supported 30 30 30 30 Large file transfers • • • • • Cable distances (m) 12.5 12.5 12.5 12.5 • • • • • • • • • • Max. transfer rate (MB/sec.
SAS selection guide ATTO ExpressSAS RAID Adapters Product Features R348 R380 4 GB/sec. 4 GB/sec. x8 PCI Express • • Number of ports 8 8 4/8 user selectable 4/4 or 0/8 8/0 1 Max.transfer rate (full duplex) Port configuration external/internal Connector type Number of devices supported 1 mini SAS (x4) SFF-8088 external 2 mini SAS (x4) SFF-8088 external 2 mini SAS (x4) SFF-8087 internal 64 SAS/SATA targets 128 virtual devices 64 SAS/SATA targets 128 virtual devices • • • • • • 1.
Celerity FC adapter selection guide Product Features Fibre Channel Ports FC protocol Maximum Transfer Rate (half duplex) Maximum Transfer Rate (fullduplex) Bus Type 3 Bus Characteristics Optical Interface Maximum Cable Length Celerity FC-44ES Celerity FC-42ES FC-42EN Celerity FC-41ES FC-41EN Celerity FC-42XS Celerity FC-41XS Celerity FC-21PS 4 2 1 2 1 1 4-Gb 4-Gb 4-Gb 4-Gb 4-Gb 2-Gb 1.6 GB/sec 800 MB/sec 400 MB/sec 800 MB/sec 400 MB/sec 200 MB/sec 2 GB/sec 1 GB/sec (ES) 1.
Appendix C Contact ATTO Technology Inc. Customer service, sales information and technical support are available by phone Monday through Friday, Eastern Standard Time 8:00 a.m. to 8:00 p.m., or by e-mail and web site 24-hours a day. ATTO Technology, Inc. 155 CrossPoint Parkway Amherst, New York 14068 (716) 691-1999 • voice (716) 691-9353 • fax http://www.attotech.com ATTO Technology can also be reached via e-mail at the following addresses: Sales Support: Technical Support: sls@attotech.
vi
