Repair Kits

ManualsBrandsAttwood ManualsHardwareFaucet

Faucet/Hand Pump

Repair Kit

6127

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69254 Rev. B 03-11

FEATURES:

The Attwood Faucet/Hand Pump Repair Kit contains a knob pin,

two (2) flapper valves, stainless disk, upper seal and lower seal.

The correct location of these parts is shown in the diagram at

right. Extra repair parts are provided for your convenience.

TOOLS AND MATERIALS REQUIRED:

1. Phillips screwdriver

2. 1/8" or 3/32" pin punch

3. Small hammer

4. Large pliers or adjustable wrench

5. Petroleum jelly

INSTALLATION INSTRUCTIONS:

NOTE: All parts must be kept clean and free of scratches

(especially the shaft). A small bit of dirt caught under

a seal can cause a leak.

Replacement of Flapper Valve & Stainless Disk:

1. Turn off water. Open faucet halfway to drain (to keep shaft

nut in place). Disconnect the water line. Disconnect electrical

connections (Model 6142 only).

2. Unscrew and remove adapter.

3. Place new flapper valve into the adapter.

4. If the shaft nut is out of the base, replace it with the word “up”

facing the pump base.

5. Add a thin film of petroleum jelly to the surface of the new

stainless disk. Center and place the disk in the shaft nut

recess. It should stay in place.

6. Screw on the adapter and hand tighten. Close the faucet.

Reconnect water and electrical.

Attwood marine hardware, navigation lighting, interior lighting, bilge

pumps, and other marine accessories are specified more than any

other brand by America’s best-known boat manufacturers as original

equipment. Look to Attwood for quality replacement parts and add-on

marine accessories.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Replacement of Upper Seal, Lower Seal & Knob Pin:

NOTE: It will be easier to make installation of new parts if

faucet is removed from countertop.

1. Turn off water. Open faucet fully to drain. Disconnect the

water line. Disconnect electrical connections (Model 6142

only). Unscrew and remove adapter. Disk and shaft nut

should fall out.

2. Unscrew large nut. Remove faucet and gasket from

countertop.

3. Remove knob pin from knob: place pin punch at small end of

knob pin and gently drive out with hammer. Remove knob

shaft from assembly.

4. Push the shaft assembly out through the bottom of base.

Remove old lower seal and gently replace new (larger)

lower seal with groove upward. See diagram.

5. For Model 6142, it is not necessary to remove electrical

switch. Keep switch actuator in place. If it falls out, refer to

diagram for replacement.

6. Unfasten all screws holding cover to body. Remove cover.

7. Remove the upper seal from the base by prying gently.

Install (smaller) upper seal by lubricating it with a small

amount of petroleum jelly. Press it gently into the base with

groove down.

8. Replace cover and fasten it with the screws.

9. Apply a thin film of petroleum jelly to the shaft and shaft seal.

Insert the shaft back through the base applying slight pres-

sure. Make sure the lower seal is centered on the shaft. Do

not damage seal.

10. Replace knob. Align knob pin holes in knob to the shaft.

Insert knob pin flush to both sides of the knob.

11. Re-install pump into countertop. Keep base gasket in place

by aligning it with base pin and holes.

12. Install large nut and tighten it one-quarter turn past hand

tight. DO NOT use any sealant.

13. Refer to Flapper Valve & Stainless Disk Instructions numbers

3, 4, 5 and 6.

TROUBLESHOOTING CHART:

Problem Probable Cause

Faucet drips at spout • Bad flapper valve

• Valve disk missing

Faucet leaks around shaft • Seal damaged or installed

upside down

• Shaft worn or scored

Faucet will not turn on or • Bad flapper valve

water flow is minimal • Valve disk caught under shaft nut

• Kinked or plugged water line

Faucet will not pump as a • Bad flapper valve

hand pump • Valve disk caught under shaft nut

• Lower seal bad or installed upside

down

6142 Only:

Electric pump will not turn on • Defective switch

or turn off. A noticeable click • Switch actuator broken or out of

is heard when the switch place

turns on or off. • No electricity

Flapper valves fail rapidly • Faucet turned beyond the off

position

• Valve disk missing

FAUCET/HAND PUMP DIAGRAM

KNOB

SCREWS

COVER

PUMP BASE

SCREW

ON SOME MODELS

COUNTER TOP

SHAFT

LOWER SEAL

GROOVE UP

BASE GASKET

STAINLESS DISK

ADAPTER

KNOB PIN

SWITCH

ACTUATOR

(POSITION)

UPPER SEAL

GROOVE DOWN

BASE GASKET

LARGE NUT

SHAFT NUT

“UP” THIS SIDE

FLAPPER VALVE