User manual

54
DW5065 All-in-one wall panel
Functions
TheDW5065istheadvancedAll-in-onewallpanelfortheM2.Thiswallpanelcontains
agraphicdisplayandcancontroltherouting,volume,bass,trebleandmuteformultiple
zones(upto8)ononeM2.Besidesthosecontrolfunctions,italsoprovidesthepossibility
toconnectamicrophoneandastereolineinputsource.TheDW5065wallpanelshould
beconnectedtotheM2usingUTP/FTPCat6(orbetter)cable.FirstreadthePIconnection
principlesinthebeginningofthischapterbeforemakinganyconnections.
ThefollowingfunctionsofmultiplezonesoftheM2canbecontrolled:
 -Volumewithinarangeof0dBto-70dB
 -Allinputscanbeselected
 -Mutecanbeactivated
 -Basswithinarangefrom-9dBto+9dB
 -Treblewithinarangefrom-9dBto+9dB
Configuration
BeforetheDW5065canoperate,theconfigurationshouldbemade.Firstofall,an
addressneedtobeassignedandtheavailableinputsneedtobedefined.
Followthesestepstoconfigure:
1)Gotothe‘Setup’menuandclick‘Peripheralconfiguration’.Toconfigurethesettings
fortheDW5065wallpanels,clickthecorrespondingbutton.Afterthisbuttonisclicked,
awindowwillbeshownwherealltheconfigurationsettingsfortheDW5065canbe
made.Ontheleftside,adropdownlistisshownwherebytheaddressfortheDW5065
canbeselected.Theaddresscanbeselectedbetween‘W001’to‘W008’.Logicallyis
startedwiththeaddress‘W001’forthefirstwallpanelandincreasestheaddressfor
everysubsequentwallpanel.Afterthedesiredaddressisselected,clickthe‘SetAddress’
buttonandthedisplayontheDW5065willstartblinking.Confirmtheaddressofthewall
panelbypushingthebigrotarybuttononthewallpanelandtheselectedaddresswillbe
assignedtothewallpanel.
2)Theoutputswhichshouldbecontrolledcanbeselectedusingthe‘Controlledoutputs’
dropdownlist.Whenselectinganoutputinthisdropdownlist,theoutputnamewillappear
inthelistboxbelow.Theoutputscanberemovedagainfromthislistboxbyselecting
them,andclickingthe‘Removeoutput’button.
3)Theinputswhichareselectablewiththewallpanelcanbechoseninthe‘Selectable
inputs’dropdownlist.Aftertheinputsareclicked,theywillappearinthelistboxshown
below.Theycanberemovedagainfromthislistboxbyselectingthem,andclickingthe
‘RemoveInput’button.
Thoseselectableinputsarenotlinkedwiththe‘Quickselectionmenu’liketheinputson
theDW3020/4020.
4)CertainactionssuchasVolumeChange,Inputchange,Mute,Tonecontrolandsettings
canbedisabledfromthewallpanelbycheckingthecheckboxes.
5)Themicrophoneinputhasthepossibilitytoprovide+15Vphantompowerforpowering
condensermicrophones.ThephantompowercanbeswitchedONandOFFbyclickingthe
‘EnableMicPhantom’checkbox.ThissettingcanalsobechangedintheDW5065settings
menu.(If‘Blocksettingsmenu’isnotchecked)