Installation and Operation HIGH DEFINITION CAT 5 MULTIDRIVER POWER Model 1171 High Definition Cat 5 MultiDriver™
Installation and Operation Manual Model 1171 High Definition Cat 5 MultiDriver™ Audio Authority and the Double-A Symbol are registered trademarks of Audio Authority Corp. AutoSelect is a trademark of Audio Authority. Copyright November, 2006, all rights reserved.
Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Other Materials You May Need . .
Getting Started • • • • Read these instructions. Unpack the product and its accessories. Connect associated equipment (detailed instructions are found in the Installation Section). Connect the product to a suitable power outlet using only the power supply provided. General Information The Model 1171, when combined with Model 9878 Cat 5 HDTV Connection Plates (Wallplates), enables HDTV signals to be distributed to multiple locations from a single source.
Audio Authority Model 1171 User Manual 5 OUTPUT 1 B A OUTPUT 2 B A OUTPUT 3 B A OUTPUT 4 CAT 5 OUTPUT JACKS Two Cat 5 cables must be connected to each Model 9878 Wallplate POWER B A B A OUTPUT 6 B COMPONENT VIDEO INPUTS Connect the source’s YPbPr output cables here OUTPUT 5 Manufactured in the USA by Audio Authority Corporation, Lexington Kentucky • 800-322-8346 or 859-233-4599 • www.audioauthority.
Installation This product should be installed by a qualified custom electronics installer. 1. Stacking. Follow these steps if you are installing this product in a stack with one or more Model 1170s. a. Lay the Model 1171 upside down on a protective surface, such as a terrycloth towel. b. Remove the four feet and the bus port cover and save them and their attaching screws for later use. c.
b. Connect all the signals available from the source unit: Component Video, Digital Audio and Analog Audio. Use either, but NOT BOTH Optical and Coaxial Digital Audio. 5. Wallplate Hookup. Caution! Do not connect A and B cables incorrectly. Do not apply system power until cables are tested and A and B connections are verified. a. Pull two lengths of good quality Category 5e or 6 UTP cable from the main system to each Wallplate location.
Troubleshooting Guide Symptom Picture has artifacts or appears sparkly Digital audio inoperative Does not repeat an IR command One Wallplate inoperative Wallplates inoperative on one Model 1171 or 1170 Possible Cause(s) Excessive cable length compensation Neither or both optical and coaxial cables connected to source Some remotes cannot be processed by this sytem; IR Output not connected to IR system Cables swapped or plugs incorrectly pinned out Bus cable loose or power supply unplugged Operation The Mod
Model 1171 Specifications Subject to change without notice.
1171 and 1170 Combination Model 1171 Cat 5 MultiDriver provides input connections for an HDTV source such as a satellite box or DVD player, and up to six Wallplate outputs. To expand the number of outputs, up to six 1170 MultiDriver Expanders can be added for a total of 42 outputs. Connect stereo analog audio, and one type of digital audio, either optical or coaxial. See “Using Compatible IR Products” on the next page for infrared control pathway functionality.
Using Compatible IR Products Receiver Pinout Receivers are powered by 12 volts on the sleeve contact of the 9878 Wallplate IR jack. Infrared signals may be transmitted from any Wallplate location back to the 1171 IR output by connecting a compatible IR receiver to the Wallplate’s IR jack. The Wallplate provides 12V power to the IR receiver; do not use IR receivers that provide their own power or damage could result. Connect a compatible emitter to the 1171’s IR output.