BENUTZERHANDBUCH OWNER’S MANUAL VERS. 1.
INHALTSVERZEICHNIS SICHERHEITSHINWEISE 3 INSTALLATIONSHINWEISE 4 X-ONE 6 Funktionen und Bedienelemente 6 Anschlussbeispiel: Tiefpass-Modus (normaler Subwoofer-Betrieb) 7 Anschlussbeispiel: Master/Slave-Modus 8 TECHNISCHE DATEN 11 FEHLERBEHEBUNG 12 OWNER’S MANUAL IN ENGLISH FROM PAGE 13 Dieses Symbol weist Sie auf wichtige Hinweise auf den folgenden Seiten hin. Bei Nichtbeachtung besteht die Gefahr das zu installierende Gerät oder Teile des Fahrzeugs zu beschädigen.
SICHERHEITSHINWEISE BITTE BEACHTEN SIE DIE FOLGENDEN HINWEISE VOR INBETRIEBNAHME! DAS GERÄT NICHT AN STELLEN EINBAUEN, AN DENEN ES HOHER FEUCHTIGKEIT ODER STAUB AUSGESETZT IST. Bauen Sie das Gerät so ein, dass es vor hoher Feuchtigkeit und Staub geschützt ist. Wenn Feuchtigkeit oder Staub in das Gerät gelangen, kann es zu Betriebsstörungen kommen. Schäden am Gerät, welche durch Feuchtigkeit hervorgerufen wurden, unterliegen nicht der Garantie.
INSTALLATIONSHINWEISE HINWEIS! Bevor Sie mit der Installation des Soundsystems beginnen, trennen Sie unbedingt den Massepol der Fahrzeugbatterie ab, um Kurzschlüsse und Stromschläge zu vermeiden. MECHANISCHE INSTALLATION Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw.entfernt werden. Vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält.
INSTALLATIONSHINWEISE ELEKTRISCHE ANSCHLÜSSE 1 2 3 4 VOR DEM ANSCHLIESSEN Für den fachgerechten Anschluss des Soundsystems sind geeignete Kabelsets im Fachhandel erhältlich. Achten Sie beim Kauf auf einen ausreichenden Kabelquerschnitt (mind. 20 mm2), den passenden Sicherungswert sowie auf die Leitfähigkeit der Kabel. Säubern und entfernen Sie vorhandene Rost- und Oxidationsstellen an allen Kontaktpunkten der Batterie und an den Massepunkten.
X- ONE FUNKTIONEN UND BEDIENELEMENTE 1 2 3 4 5 6 7 8 1 Die SLAVE IN/MASTER OUT-Cinchanschlüsse dienen zum Anschluss eines weiteren Verstärkers im MASTER/SLAVE-Modus. Beachten Sie dazu den Abschnitt Anschlussbeispiel: MASTER/SLAVE auf Seite 8. 2 Die LINE INPUT Cinch-Audioeingänge müssen per Cinch-Kabel mit dem Steuergerät verbunden werden. Alle 2 Line-Eingänge müssen belegt sein. Sollten Sie nur einen Stecker zur Verfügung haben, verwenden Sie einen Y-Adapter zum Splitten des Signals.
X- ONE ANSCHLUSSBEISPIEL: Tiefpass-Modus mit einem Subwoofer Bass-Fernbedienung mittels beiliegendem Kabel mit dem Anschluss am Verstärker verbinden (REMOTE) Schalterstellung MASTER OUT Stereo Cinch-Audiokabel (R/L oder SUB OUT) vom Steuergerät mit dem LINE INPUT R/L verbinden L R Subwoofer 1 – 8 Ohm VERKABELUNG • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cinch-Eingängen (LINE INPUT) des Verstärkers mittels • geeigneten hochwertigen Cinch-Audiokabeln.
X- ONE ANSCHLUSSBEISPIEL: Master/Slave-Modus mit zwei Verstärker Verbinden Sie das Stereo Cinch-Audiokabel (L/R od. SUB OUT) vom Steuergerät mit LINE INPUT L/R des MASTER- Verstärkers. L MASTER R Verbinden Sie den Cinch-Anschluss MASTER OUT vom MASTERVerstärker mit dem Cinch-Anschluss SLAVE IN des SLAVE-Verstärkers.
X- ONE ANSCHLUSSBEISPIEL: Subwoofer mit Single-Schwingspule MASTER MASTER/SLAVE Link wie auf Seite 8 beschrieben. SLAVE Die Impedanz des Subwoofers von 2 Ohm darf nicht unterschritten werden. Subwoofer 2 – 8 Ohm ANSCHLUSSBEISPIEL: Subwoofer mit Dual-Schwingspule MASTER MASTER/SLAVE Link wie auf Seite 8 beschrieben. Subwooferschwingspule 1 1 – 8 Ohm SLAVE Subwooferschwingspule 2 1 – 8 Ohm Beim Verstärker SLAVE muss die Subwooferschwingspule mit umgekehrter Polung angeschlossen werden.
TECHNISCHE DATEN MODELLE X-ONE KANÄLE SCHALTUNGSPRINZIP 1 CLASS D Digital AUSGANGSLEISTUNG RMS 13,8 V Watt an 4 Ohm Watt an 2 Ohm Watt an 1 Ohm 1 x 300 1 x 500 1 x 750 AUSGANGSLEISTUNG MAX. 13,8 V Watt an 4 Ohm Watt an 2 Ohm Watt an 1 Ohm 1 x 600 1 x 1000 1 x 1500 Dämpfungsfaktor Signal-Rauschabstand Klirrfaktor (THD&N) Eingangsempfindlichkeit Eingangsimpedanz >200 >95 dB <0,1% 6 - 0.
FEHLERBEHEBUNG STATUSANZEIGE & SCHUTZSCHALTUNG Die STATUSANZEIGE (ESX LOGO) befindet sich auf der Oberseite des Verstärkers. 1. Leuchtet die STATUSANZEIGE ist der Verstärker betriebsbereit. Auf der Kabel-Fernbedieung befindet sich zudem eine POWER LED, welche die gleiche Funktion hat. 2. Beginnt die STATUSANZEIGE zu blinken liegt eine Fehlfunktion vor. Auf der Kabel-Fernbedieung befindet sich zudem eine PROTECT LED, welche die gleiche Funktion hat.
FEHLERBEHEBUNG Fehler: keine Funktion Ursache: Lösung: 1. Die Stromversorgungskabel sind nicht korrekt angeschlossen. Erneute Überprüfung 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. Erneute Überprüfung 3. Die Remote-Steuerleitung des Steuergeräts (Autoradio) ist nicht korrekt am Verstärker angeschlossen. Erneute Überprüfung 4. Sicherungen defekt. Im Falle des Austauschs achten Sie bitte auf den korrekten Wert der Sicherungen.
TABLE OF CONTENT SAFETY INSTRUCTIONS 14 INSTALLATION INSTRUCTIONS 15 X-ONE 17 Features and operational controls 17 Interconnection example Low Pass-Mode (standard subwoofer operation) 18 Interconnection example Master/Slave-Mode 19 SPECIFICATIONS 21 TROUBLE SHOOTING 22 This symbol adverts you an important reference note on the following pages. Attend these reference notes by any means, otherwise damage of the device or the vehicle may be caused.
SAFETY INSTRUCTIONS PLEASE OBSERVE THE FOLLOWING ADVICES BEFORE THE FIRST OPERATION! DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE EXPOSED TO HIGH HUMIDITY AND DUST. Install the device at a location, where it will be protected from high humidity and dust. If humidity and dust attain inside the device, malfunctions may be caused. THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE.
INSTALLATION INSTRUCTIONS REFERENCE NOTE Before you start with the installation of the sound system, disconnect by any means the GROUND connection wire from the battery, to avoid any risk of electric shock and short circuits. MECHANICAL INSTALLATION Avoid any damage removing of the components of the vehicle like wires, cables, board computer, seat belts, gastank or the like. Ensure that chosen location provide sufficient air circulation for the amplifier.
INSTALLATION INSTRUCTIONS ELECTRICAL INTERCONNECTION 1 2 3 4 BEFORE THE CONNECTION For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient profile section (at least 20 mm2), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
X- ONE FUNCTIONS AND OPERATIONAL CONTROLS 1 2 3 4 5 6 7 8 1 The MASTER OUT / SLAVE IN RCA jacks are suitable to connect an additional amplifier in MASTER/SLAVE mode. Attend therefor the chapter Interconnection Example: MASTER/SLAVE on page 19. 2 The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit. Both jacks must be used. If your headunit provide only one RCA jack, you need to split the signal with a y-connector.
X- ONE INTERCONNECTION EXAMPLE Low Pass-Mode (Standard Subwoofer Operation) Connect the bass remote controller and the remote terminal on the amplifier with the enclosed cable. Switch position MASTER OUT Connect stereo RCA output (R/L or SUB OUT) of the headunit with LINE INPUT R/L of the amplifier R L Subwoofer 1 – 8 Ohms INTERCONNECTION • Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
X- ONE INTERCONNECTION EXAMPLE Master/Slave Mode Connect Stereo RCA output (L/R or SUB OUT) of the headunit with the LINE INPUT L & R of the MASTER amp L R MASTER Connect Stereo RCA output MASTER OUT of the MASTER amp with the RCA input SLAVE IN of the SLAVE amp. Switch position MASTER OUT SLAVE Switch position SLAVE IN Connect the bass remote controller and the remote terminal at the amplifier (MASTER) with the enclosed cable.
X- ONE INTERCONNECTION EXAMPLE 1 Subwoofer with a Single-Voicecoil MASTER MASTER/SLAVE Link like described on page 19. SLAVE The Impedance may not be lower than 2 ohms. Subwoofer 2 – 8 Ohms INTERCONNECTION EXAMPLE 1 Subwoofer with a Dual-Voicecoil MASTER MASTER/SLAVE Link like described on page 19. Subwoofer Voice Coil 1 1 – 8 Ohms SLAVE Subwoofer Voice Coil 2 1 – 8 Ohms The subwoofer voice coil on the SLAVE amp needs to be connected with a converse polarity.
SPECIFICATIONS MODELS X-ONE CHANNELS CIRCUIT 1 CLASS D Digital OUTPUT POWER RMS 13,8 V Watts @ 4 Ohms Watts @ 2 Ohms Watts @ 1 Ohm 1 x 300 1 x 500 1 x 750 OUTPUT POWER MAX. 13,8 V Watts @ 4 Ohms Watts @ 2 Ohms Watts @ 1 Ohm 1 x 600 1 x 1000 1 x 1500 Damping Factor Signal-to-Noise Ratio THD&N Input Sensitivity Input Impedance >200 >95 dB <0,1% 6 - 0.
TROUBLE SHOOTING STATUS INDICATOR & PROTECTION CIRCUIT The STATUS INDICATOR (ESX LOGO) is located on the top side of the amplifier. 1. If the STATUS INDICATOR lights up, the amplifier is turned on and is ready for operation. You find also a POWER LED on the remote controller which owns the same function. 2. If the STATUS INDICATOR starts flashing, a malfunction occurs on the amplifier. You find also the a PROTECT LED on the remote controller which owns the same function.
TROUBLE SHOOTING Malfunction: no function Reason: Remedy: 1. The power supply connection of the device is not correct. Recheck 2. The cabels have no mechanical or electrical contact. Recheck 3. The remote turn-on connection from the headunit to the amplifier is not correct. Recheck 4. Defective Fuses. In case of replacing the fuses, attend by any means the correct fuse rating. Replace Fuses Malfunction: no signal on loudspeakers, but STATUS INDICATOR is on Reason: Remedy: 1.
CAR AUDIO SYSTEMS Audio Design GmbH · www.audiodesign.de Am Breilingsweg 3 · D-76709 Kronau (Germany) Tel.